YASKAWA VS?616G5 Owner's Manual page 78

Name
Constant
(Digital Operator Display)
No.
E4−01 Motor 2 max. output frequency
(V/F2 Max Freq)
E4−02 Motor 2 max. voltage
:
(V/F2 Max Voltage)
E4−03 Motor 2 max. voltage frequency
(V/F2 Base Freq)
E4−04 Motor 2 mid. output frequency 1
(V/F2 Mid Freq)
E4−05
Motor 2 mid. output frequency voltage 1
(V/F2 Mid Voltage)
E4−06
Motor 2 min. output frequency
(V/F2 Min Freq)
E4−07 Motor 2 min. output frequency voltage
(V/F2 Min Voltage)
E5−01 Motor 2 rated current :
(Motor 2 rated FLA)
E5−02 Motor 2 rated slip
:
(Motor 2 Slip Freq)
E5−03 Motor 2 no−load current
(Motor 2 No−load I)
E5−04
Motor 2 number of poles
(Motor 2 # Poles)
E5−05 Motor 2 line−to−line resistance
(Motor 2 term Ohms)
E5−06 Motor 2 leak inductance
(Motor 2 Leak)
F1−01 PG constant
(PG Pulse/Rev)
F1−02 Operation selection at PG open circuit
(PG Fdbk Loss Sel)
F1−03 Operation selection at overspeed
(PG Overspeed Sel)
F1−04 Operation selection at deviation
(PG Deviation Sel)
F1−05 PG rotation
(PG Rotation Sel)
F1−06 PG division rate (PG pulse monitor)
(PG Output Ratio)
F1−07 Integral value during accel/decel enable/disable
(PG Ramp PI/I Sel)
F1−08 Overspeed detection level
(PG Overspd Level)
F1−09 Overspeed detection delay time
(PG Overspd Time)
F1−10 Excessive speed deviation detection level
(PG Deviate Level)
F1−11 Excessive speed deviation detection delay time
(PG Deviate Time)
F1−12 Number of PG gear teeth 1
(PG# Gear Teeth 1)
F1−13 Number of PG gear teeth 2
(PG# Gear Teeth 2)
F1−14 PG open−circuit detection time
(PGO Time)
F2−01 Bi−polar or uni−polar input selection
(AI−14 Input Sel)
F3−01 Digital input option
(DI Input)
F4−01 Channel 1 monitor selection
(AO Ch1 Select)
F4−02 Channel 1 gain
(AO Ch1 Gain)
Table A−4 Constants List (Cont'd)
Initial
Setting
: 60
575
: 60.0
3.0
:
[
31.6
:
[
0.5
:
[
: 5.7
[
22
]
1.6
]
6.6
:
]
4
:
0.896
:
]
17.2
:
]
600
1
1
3
0
1
0
115
0.0
[
10
0.5
0
0
2.0
:
0
0
2
1.00
: Not displayed for some models depending on software version No.
[
Differs depending on the control method selection (A1−02).
]
Setting unit and initial setting differ depending on inverter capacity.
# Initial settings in the parentheses are values obtained at 3−wire initialization.
User
Constant
Setting (Digital Operator Display)
No.
F4−03 Channel 2 monitor selection
(AO Ch2 Select)
F4−04 Channel 2 gain
(AO Ch2 Gain)
F5−01 Channel 1 output selection
(DO−02 Ch1 Select)
F5−02 Channel 2 output selection
(DO−02 Ch2 Select)
F6−01 Output mode selection
(DO−08 Selection)
F7−01 Frequency multiple selection
(PO−36F Selection)
H1−01 Multi−function input (terminal 3)
(Terminal 3 Sel)
H1−02 Multi−function input (terminal 4)
(Terminal 4 Sel)
H1−03 Multi−function input (terminal 5)
(Terminal 5 Sel)
H1−04 Multi−function input (terminal 6)
(Terminal 6 Sel)
H1−05 Multi−function input (terminal 7)
(Terminal 7 Sel)
H1−06 Multi−function input (terminal 8)
(Terminal 8 Sel)
H2−01 Multi−function input (terminal 9−10)
(Terminal 9 Sel)
H2−02 Multi−function input (terminal 25−27)
(Terminal 25 Sel)
H2−03 Multi−function input (terminal 26−27)
(Terminal 26 Sel)
H3−01 Signal level selection (terminal 13)
(Term 13 Signal)
H3−02 Gain (terminal 13)
(Terminal 13 Gain)
H3−03 Bias (terminal 13) bias
(Terminal 13 Bias)
H3−04 Signal level selection (terminal 16)
(Term 16 Signal)
H3−05 Multi−function analog input (terminal 16)
(Terminal 16 Sel)
H3−06 Gain (terminal 16)
(Terminal 16 Gain)
H3−07 Bias (terminal 16)
(Terminal 16 Bias)
H3−08 Signal level selection (terminal 14)
(Term 14 Signal)
H3−09 Multi−function analog input (terminal 14)
(Terminal 14 Sel)
H3−10 Gain (terminal 14)
(Terminal 14 Gain)
H3−11 Bias (terminal 14)
(Terminal 14 Bias)
H3−12 Analog input filter time constant
(Filter Avg Time)
H4−01 Monitor selection (terminal 21)
(Terminal 21 Sel)
H4−02 Gain (terminal 21)
(Terminal 21 Gain)
H4−03 Bias (terminal 21)
(Terminal 21 Bias)
H4−04 Monitor selection (terminal 23)
(Terminal 23 Sel)
APPENDIX 4 CONSTANTS LIST
Name Initial
Setting
3
0.50
0
1
0
1
24
14
3(0)
#
4(3)
#
6(4)
#
8(6)
#
0
1
2
0
100.0
0.0
0
0
100.0
0.0
2
1F
100.0
0.0
0.00
2
1.00
0.0
3
User
Setting
79