Related Manuals for Thinklogical DCS StudioPRO
Summary of Contents for Thinklogical DCS StudioPRO
- Page 1 DCS StudioPRO USB and Video Extender Product Manual Thinklogical Inc. 100 Washington Street Milford, Connecticut 06460 U.S.A. Telephone (203) 647-8700 Fax (203) 783-9949 www.thinklogical.com MAN-000018 REVISION A...
- Page 3 Thinklogical, a subsidiary of Logical Solutions, Incorporated 100 Washington Street Milford, Connecticut 06460 U.S.A. Telephone (203) 647-8700 All trademarks and service marks are property of their respective owners. Document ID: MAN-000018 Subject: DCS StudioPRO USB and Video Extender Revision: Rev A, August 2007 MAN-000018 REVISION A...
-
Page 4: Table Of Contents
Transmitter ........................12 3.4.2. Receiver ......................... 12 3.5. General Button Usage – DDC Select..................13 3.5.1. Operation of the Thinklogical DDC Modes ..............13 Regulatory and Safety........................15 4.1. Safety Requirements ......................15 4.1.1. Symbols Found on Product..................... 15 4.1.2. - Page 5 Appendix A Ordering Information ...................... 21 StudioPRO Extenders ......................21 Related Products - DCS StudioPRO Matrix Switch..............21 Appendix B Enclosure Dimensions ......................22 MAN-000018 REVISION A...
-
Page 7: Introduction
1. Introduction 1.1. Intended Application The StudioPRO Extender (SPE) is a fiber optic extender designed to extend USB 1.1 or USB 2.0 and DVI video signals up to 1000 meters (3280 feet) over standard duplex multimode fiber. With the SPE, all USB 1.1 or USB 2.0 peripherals can be conveniently located while operating at optimal speed. -
Page 8: Laser Information
1.3. Laser Information LASER RADIATION DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS CAUTION: In order to avoid possible exposure to laser energy, it is good practice to attach the fiber optic cables prior to applying power to the StudioPRO EXTENDER. If the fiber optic cable should become disconnected, DO NOT attempt to look into the cable or the panel mounted connector. -
Page 9: System Features
2. System Features 2.1. General System Features The SPE systems are designed for high-resolution video and USB extension applications, such as remote projection centers, theaters and assembly halls, and for secure computer installations. The ability to remotely locate the CPU away from the monitor and peripherals allow more control of your computer environment. -
Page 10: Transmitter
2.2.1. Transmitter Figure 2: Front and Back Views of the SPE Transmitter Models 2.2.2. Receiver Figure 3: Front and Back Views of the SPE Receiver Models MAN-000018 REVISION A... -
Page 11: Technical Specifications
2.3. Technical Specifications Each Logical Solutions StudioPRO Extender system is designed to the following specifications: Electrical Cable USB Type A to USB Type B Cable, 6FT (supplied with system) DVI-I Male to DVI-D Male Cable, 2M (Single Link Model Only) DVI-D Male to DVI-D Male Dual-Link Cable, 2M (Dual Link Model Only) Connectors Single-Link Receiver:... - Page 12 Two fibers for USB; Two fibers for video All Fiber is multi-mode, 50 micron or 62.5 micron. (Fiber Cable is either customer-supplied or can be ordered from Thinklogical.) Operating Temperature 0 to 50 °C (32 to 122 °F), 5 to 95% RH, non-condensing...
-
Page 13: Connecting The Spe System
3. Connecting the SPE System 3.1. Overview StudioPRO Extender Connection Diagrams SPE-SL2.0 5 VDC 5 V DC 3 fibers receiver P OWER POWER DVI FROM CPU DVI LOCAL DIS PLAY US B2 .0 DVI TO DISP LAY USB 2 .0 S INGL E L INK SINGLE LINK SINGLE LINK... -
Page 14: Contents
3.2. Contents When you receive your Thinklogical StudioPRO Extender system, you should find the following items: StudioPRO Extender – Transmitter StudioPRO Extender – Receiver AC Power Supply (PWR-000022-R) – Quantity 2 USB Cable, 6 Feet (for the Transmitter unit) ... -
Page 15: Fiber Optic Cables
Fiber Optic cables for the SPE system are not included, but are available for purchase. Please contact thinklogical for a quotation on your required cable length. A fiber optic cable must be run between the location of the SPE Transmitter (near your CPU or other DVI-D video source) and the SPE Receiver (near the monitor, projector, etc.). - Page 16 Connect your fiber cable to the ST-type connector on each SPE pair (one Transmitter and one Receiver). Dress the cable so it will not get crushed, pinched or otherwise damaged. When connecting the fiber optic cables, you must be sure to: ...
-
Page 17: Ac Power Supply - Pwr-000022-R (Quantity 2)
3.3.4. USB Type B – Transmitter Connect your PC to the location on the Transmitter unit using the USB Type A to USB Type B Cable (CBL000015-006FR) that was provided with your SPE system. Figure 7: USB Type B Connector 3.3.5. -
Page 18: Led Status
3.4. LED Status 3.4.1. Transmitter LED Label Status DDC Pass LED is ON (solid green) for DDC Pass thru mode. In this mode, the CPU communicates directly with the connected monitor for DDC information. DDC Dynamic LED is ON (solid green) for DDC Dynamic mode. In this mode, the DDC of the monitor is read from the receiver and stored in the transmitter. -
Page 19: General Button Usage - Ddc Select
(EDID) and provide video acceptable to the monitor. Due to the Thinklogical TX emulating a monitor it must provide a DDC table to the video card in order for the video card to provide images for transport. Some video cards are very un-forgiving of DDC data. An un-forgiving video card will shut off video output if the DDC is not present at boot up (missing monitor), hot-plugged or the DDC information does not match expected parameters (digital or analog). - Page 20 3.5.1.2. Static Mode Static DDC mode is typically used in DCS switched situations. In some switched situations the customer may be using multiple monitors that are all capable of handling the same video resolution but for one reason or another, some of the monitors in the system cause some video cards issues that cause the video card to turn off the video output.
-
Page 21: Regulatory And Safety
4. Regulatory and Safety Regulatory and Safety Testing are pending at this time. 4.1. Safety Requirements 4.1.1. Symbols Found on Product Markings and labels on the product follow industry-standard conventions. Regulatory markings found on the products comply with requirements. 4.1.1.1. Class 1M LASER Labeling CLASS 1M LASER PRODUCT 4.1.2. -
Page 22: North America
Logical Solutions Inc. 100 Washington Street Milford, Connecticut 06460 USA Telephone (203) 647-8700 Product Name Model: DCS StudioPRO USB and Video Extender These products comply with the requirements of the Low Voltage Directive 72/23/EEC and the EMC Directive 89/336/EEC. MAN-000018 REVISION A... -
Page 23: Standards With Which The Products Comply
4.5.2. Standards With Which the Products Comply Safety • IEC60950:1992+A1, A2, A3, A4, A11 LASER Safety • IEC60825-1/2 • Class 1 LASER Product Electromagnetic Emissions • EN55022: 1994 (IEC/CSPIR22: 1993) • EN61000-3-2/A14: 2000 • EN61000-3-3: 1994 Electromagnetic Immunity • EN55024: 1998 Information Technology Equipment-Immunity Characteristics •... - Page 24 __________________________________________________________________________________ This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe A respecte toutes les exigencies du Règlement sur le matérial brouilleur du Canada. __________________________________________________________________________________ WARNING This is a Class A product. In a domestic environment this product may cause radio interference, in which case the user may be required to take adequate measures.
-
Page 25: How To Contact Us
Acrobat reader needed to view PDF files, visit www.adobe.com for a download. 5.1.2. Email Thinklogical is staffed Monday through Friday from 8:30am to 5:30pm, Eastern Time Zone. We will try to respond to your email inquiries promptly, use the following email addresses for your different needs: info@thinklogical.com –... -
Page 26: Fax
5.2.1. Warranty Thinklogical Inc. products carry a one year warranty, with longer term available at time of purchase on most products. Please refer to your product invoice for your products Warranty Terms & Conditions. 5.2.2. Return Authorization If, for some reason you need to return your thinklogical product to us, please get a Return Authorization Number (RA# or RMA#) from thinklogical’s Product Support department before... -
Page 27: A.1 Studiopro Extenders
SPE-DL1.1-SCRX StudioPRO Receiver, Dual-Link DVI, USB 1.1, SC SPE-DL1.1-LCRX StudioPRO Receiver, Dual-Link DVI, USB 1.1, LC A.2 Related Products - DCS StudioPRO Matrix Switch SPS-000001 StudioPRO Chassis, Fully Loaded, Dual Power Supplies SPC-000001 StudioPRO Chassis, Including CPU, Fans, Dual Power Supplies... -
Page 28: Appendix B Enclosure Dimensions
Appendix B Enclosure Dimensions MAN-000018 REVISION A...