Advertisement
Quick Links
Download this manual
See also:
Owner's Manual
BOTH PROGRAMMED IGNITION
KEYS ARE REQUIRED AT TIME
OF INSTALLATION
PART NUMBER (s):
0000-8F-H13
HOOD SAFETY SWITCH KIT CONTENTS
(P/N: 0000-8F-H03)
Hood Safety
1/4" Self
Switch
Drilling Screws
(QTY 1)
(QTY 2)
Tie Wrap
IDC Wire Tap
(QTY 2)
(QTY 2)
IMMOBILIZER INTERFACE KIT CONTENTS
(P/N: 0000-8F-H05)
Immobilizer Interface
Adhesive Primer
Module and Harness
(QTY-1)
TOOLS REQUIRED
SAFETY GLASSES
ELECTRICAL TAPE
WIRE CUTTERS
PLIERS
ALCOHOL or GLASS CLEANER
PHILLIPS SCREWDRIVER
POWER DRILL
1
VEHICLE PREPARATION
1. Remove the driver's side lower dash panel.
a. Unclip the hood release by inserting a fiber stick between the
hood release and the dash panel. There is a center tab the
stick must push down while pulling hood release towards the
rear of the vehicle.
b. Remove (2) 8mm bolts behind the hood release cable.
(FIGURE A)
c. Unsnap lower dash panel using a fiber stick starting at the
bottom.
d. Unplug the trunk release connector after removing the lower
dash panel.
2. Remove the driver's side lower dash kneeblocker bracket (4) phil-
lips head screws and remove bracket. (FIGURE B)
GENUINE ACCESSORIES
INSTALLATION INSTRUCTIONS
REMOTE START SYSTEM
Remote Start
Locking
Control Module
Washer
(QTY-1)
(QTY 2)
P/N: 0000-8F-Z01
MAZDA
GENUINE ACCESSORIES
Vehicle Remote Start System
Owner's Manual
Featuring PowerCode Technology
For the Ultimate in Comfort, Convenience and Security
TM
Owners
Manual
(QTY 1)
2- Sided Tape
(QTY-1)
(QTY-1)
9/32" DRILL BIT
FIBER STICK
10mm SOCKET AND RATCHET
8mm SOCKET AND RATCHET
1/4" SOCKET AND DRIVE
3/8" DRIVE TORQUE WRENCH
3/8" DRIVE 10mm SOCKET
KIT CONTENTS
DNA Card
(QTY-1)
P/N: 0000-8F-H16
2 sec.
5X
2 sec.
30
TM
sec.
Wallet
Card
(QTY 1 / 0000-8F-Z12)
QTY 1, P/N 0000-8F-Z12
(QTY 1)
PARTS BAG CONTENTS
Tie Wrap
(QTY-10)
0
PRE INSTALLATION
1. CLEAN HANDS
2. OPEN DRIVER'S DOOR WINDOW
3. RECORD RADIO STATIONS
4. SET PARKING BRAKE
5. DISCONNECT AND ISOLATE
NEGATIVE BATTERY TERMINAL
6. VEHICLE MUST BE AT ROOM
TEMPERATURE
1
®
APPLICABLE MODELS:
2006>MAZDA6
ALL MODELS
Remote Start
Dipole Antenna
Transmitters
(QTY-1)
(QTY-2)
P/N: 0000-8F-Z02
P/N: 0000-8F-Z10
WARNING: / AVERTISSEMENT
This vehicle is equipped with a remote controlled engine starter.
To reduce the risk of serious Injury or death, switch engine starter
system into service mode and disconnect the vehicle battery
before performing any service on the vehicle.
Ce véhicule est doté d'un démarreur à distance. Pour réduire les
risques de blessures graves ou mortelles, mettre le démarreur à
distance en mode service et débrancher la batterie du véhicule
avant d'effectuer des travaux d'entretien sur celui-ci.
Underhood
Long Tie
Sticker
Wrap
(QTY 1)
(QTY 4)
IDC Wire Tap
FIGURE A
FIGURE B
1030832 Rev.A 10/05
Remote Start
Wire Harness
(QTY-1)
P/N: 0000-8F-H17
Mini Fuses
(QTY - (1) 5 AMP)
(QTY - (7) 15 AMP)
(QTY-4)
Advertisement
Related Manuals for Mazda 6 2006
Summary of Contents for Mazda 6 2006
-
Page 1: Kit Contents
P/N: 0000-8F-Z01 P/N: 0000-8F-H16 P/N: 0000-8F-Z02 P/N: 0000-8F-Z10 P/N: 0000-8F-H17 MAZDA GENUINE ACCESSORIES WARNING: / AVERTISSEMENT Vehicle Remote Start System This vehicle is equipped with a remote controlled engine starter. To reduce the risk of serious Injury or death, switch engine starter Owner's Manual 2 sec. - Page 2 VEHICLE PREPARATION, continued 3. Using a fiber stick, remove the driver’s side scuff plate and driver’s side kick panel cover. (FIGURE 4. Remove the lower steering column shroud. a. Remove (3) phillips head screws (1 dark machine head, 2 gold coarse thread). Note that the (2) course screws go in the (2) holes closest to the steering wheel.
- Page 3 DIPOLE ANTENNA MOUNTING, continued 3. Route the antenna wire down the A-pillar securing it to the exist- ing wiring using (3) of the supplied tie wraps. Do not secure it directly to the sunroof drain tube or airbag. (FIGURE I) 4.
- Page 4 HOOD SAFETY SWITCH MOUNTING, continued 3. Remove (2) push pins from driver’s side of hood insulation (FIGURE M). Tuck the wiring from the hood safety switch under the hood insulation and route towards the driver’s side of the hood. (FIGURE N) FIGURE N FIGURE M 4.
- Page 5 REMOTE START CONTROL MODULE PREPARATION 1. Insert the supplied fuses into the remote start control module as shown in below (FIGURE R). The fuses fit tight so use a tool handle to seat them in place if necessary. 2. Install DNA card into the remote start control module as shown below. (FIGURE S) 3.
- Page 6 REMOTE ENGINE START MODULE AND IMMOBILIZER INTERFACE MOUNTING REMOTE ENGINE START MOUNTING, VEHICLE’S EQUIPPED WITH V-6 ENGINE 1. Route the 2-pin dipole antenna connector (previously installed in step 2) to the remote engine start control module and plug into the 2-pin port on the back side of the module. 2.
- Page 7 1030832 Rev.A 10/05...
- Page 8 WIRE HARNESS CONNECTIONS- STEERING COLUMN 1. Route the immobilizer interface (previously installed) ribbon cable to the ignition switch, making sure to keep it away from any moving parts. 2. Following the instructions on the supplied ampule of adhesive primer, apply a thin coating to the entire transceiver antenna ring (black plas- tic ring around key switch, FIGURE CC) and to the ribbon cable.
- Page 9 WIRE HARNESS CONNECTIONS- STEERING COLUMN, continued 11. Loosely secure the remote start harness to the left side of the steering column harness using (2) supplied tie wraps. Verify mo- bility of the steering column by moving the tilt and telescoping features of the steering column making sure that the remote start harness and ignition connector is placed so that it will not inter- fere or come into contact with any of the moving parts.
- Page 10 WIRE HARNESS CONNECTIONS-HOOD SAFETY SWITCH 1. Locate the (2) isolated wires (GRAY/RED & BLACK/ORANGE) at the remote start harness. 2. Locate the wires listed below. If the hood safety switch wire has a ground ringlet terminal or a stripped end on either wire then cut the ends of the wire so they are blunt. 3.
- Page 11 WIRE HARNESS CONNECTIONS-DRIVER’S KICK PANEL, continued BRAKE SAFETY SWITCH INPUT CONNECTION 8. Locate the 8-pin connector on the back of the BCM/fusebox as- sembly (FIGURE JJ) and locate the wire listed below. 9. Place one of the supplied IDC wire tap on each the vehicle wire (using the side of the IDC wire tap that is open on both ends).
- Page 12 EMERGENCY OVERRIDE/PROGRAMMING BUTTON MOUNTING 1. Locate the previously removed driver’s side kick panel cover. 2. Drill a 9/32” hole at the top of the panel, approximately 50mm down and 75mm from leading edge. 3. Route the emergency override/programming button from the remote start harness down to the kick panel. 4.
- Page 13 REASSEMBLY, continued 4. Re-install the driver’s side kneeblocker panel with the (4) phillips screws. (FIGURE SS) 5. Re-install the driver’s side lower dash panel. a. Plug the trunk release connector into the switch on the panel (sedan only) and carefully snap the driver’s side dash panel into place.
- Page 14 IMMOBILIZER INTERFACE PROGRAMMING NOTE: IF YOU DID NOT START THE CAR WITH THE IGNITION KEY AS INSTRUCTED TO IN SECTION 10 STEP 5 THEN THE VEHICLE WILL NOT ATTEMPT TO START, INSTEAD YOU WILL GET THREE ADDITIONAL BEEPS FROM THE HORN. THE VEHICLE HAS TO BE STARTED AT LEAST ONCE WITH THE KEY FOR THE REMOTE ENGINE START FUNCTION TO OPERATE.
- Page 15 FUNCTION TEST - continued Remote Engine Start Functions 1. REMOTE ENGINE START; Make sure the key is removed from the ignition switch and the engine hood is closed. Press the START button (2) times - The parking lights should flash three times, the horn should beep once the driver’s door should unlock and then re-lock then the vehicle should crank and start.
- Page 16 SYSTEM PROGRAMMING NOTE: THE FOLLOWING STEPS ARE ONLY NECESSARY IF YOU NEED TO PROGRAM ADDITIONAL TRANSMITTERS. 1. Transmitter Programming NOTE: The transmitters shipped with the remote start system are pre-programmed to the DNA card, and do not need to be reprogrammed. a.
- Page 17 1030832 Rev.A 10/05...
- Page 18 1030832 Rev.A 10/05...