Table of Contents
Advertisement
PART NUMBER (s):
0000-8F-N02B
NOTE: BOTH VEHICLE IGNITION KEYS ARE REQUIRED AT TIME OF
INSTALLATION. DO NOT BEGIN INSTALLATION WITHOUT BOTH
KEYS.
HOOD SAFETY SWITCH KIT CONTENTS
P/N: 0000-8F-H03
Hood Safety
Switch
(QTY 1)
Locking
Washer
(QTY 2)
Wire Tie
IDC Wire Tap
(QTY 2)
IMMOBILIZER INTERFACE KIT CONTENTS
P/N: 0000-8F-H05A
Immobilizer Interface
Adhesive Primer
Module and Harness
(QTY-1)
TOOLS REQUIRED
SAFETY GLASSES
ELECTRICAL TAPE
WIRE CUTTERS
PLIERS
ALCOHOL or GLASS CLEANER
#2 PHILLIPS SCREWDRIVER
POWER DRILL
9/32" DRILL BIT
FIBER STICK
10 mm SOCKET AND RATCHET
1/4" SOCKET AND DRIVE
3/8" DRIVE TORQUE WRENCH
3/8" DRIVE 10mm SOCKET
HI-TEMPERATURE SILICONE
GENUINE ACCESSORIES
INSTALLATION INSTRUCTIONS
REMOTE START SYSTEM
1/4" Self
Remote Start
Drilling Screws
Control Module
(QTY 2)
(QTY-1)
P/N: 0000-8F-Z01
MAZDA
GENUINE ACCESSORIES
Vehicle Remote Start System
Owner's Manual
Featuring PowerCode Technology
TM
TM
For the Ultimate in Comfort, Convenience and Security
Owners
Manual
(QTY 2)
(QTY 1)
2- Sided Tape
(QTY-1)
(QTY-1)
0
1. CLEAN HANDS
2. OPEN DRIVER'S DOOR WINDOW
3. RECORD RADIO STATION PRESETS
4. SET PARKING BRAKE
5. ENSURE VEHICLE WILL START UTILIZING THE IGNITION KNOB & VALET
KEY (SMART-KEY EQUIPPED VEHICLES ONLY)
6. DISCONNECT AND ISOLATE NEGATIVE BATTERY TERMINAL
7. VEHICLE MUST BE AT ROOM TEMPERATURE
KIT CONTENTS
DNA Card
Remote Start
(QTY-1)
Transmitters
(QTY-2)
P/N: 0000-8F-M21
P/N: 0000-8F-Z02
WARNING: / AVERTISSEMENT
This vehicle is equipped with a remote controlled engine starter.
To reduce the risk of serious Injury or death, switch engine starter
system into service mode and disconnect the vehicle battery
before performing any service on the vehicle.
Ce véhicule est doté d'un démarreur à distance. Pour réduire les
risques de blessures graves ou mortelles, mettre le démarreur à
distance en mode service et débrancher la batterie du véhicule
2 sec.
avant d'effectuer des travaux d'entretien sur celui-ci.
5X
2 sec.
30
sec.
Underhood
Wallet
Sticker
Card
(QTY 1)
(QTY 1)
P/N: 0000-8F-Z12
Programming
Button
(QTY 1)
P/N: 0000-8F-Z03
PARTS BAG CONTENTS
Wire Tie
(QTY-10)
1
®
APPLICABLE MODELS:
2007 > MAZDA CX-9
ALL MODELS
Dipole Antenna
(QTY-1)
P/N: 0000-8F-Z10
(QTY - (1) 5 AMP)
(QTY - (7) 15 AMP)
Long Wire
Tie
(QTY 4)
IDC Wire Tap
(QTY-8)
4280159 Rev. A 10/10
Remote Start
Wire Harness
(QTY-1)
P/N: 0000-8F-N18A
Mini Fuses
Advertisement
Table of Contents
Related Manuals for Mazda 0000-8F-N02B
Summary of Contents for Mazda 0000-8F-N02B
- Page 1 GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS PART NUMBER (s): REMOTE START SYSTEM APPLICABLE MODELS: 0000-8F-N02B 2007 > MAZDA CX-9 ALL MODELS NOTE: BOTH VEHICLE IGNITION KEYS ARE REQUIRED AT TIME OF INSTALLATION. DO NOT BEGIN INSTALLATION WITHOUT BOTH KEYS. KIT CONTENTS HOOD SAFETY SWITCH KIT CONTENTS P/N: 0000-8F-H03 1/4”...
- Page 2 ELECTRICAL SYSTEM GENERAL PROCEDURES W ire color code C onnector diagrams Two-color wires are indicated by a two-letter Connector diagrams show connectors on the harness symbol.The first indicates the base color of the side. The terminal indicates the view from the harness wire, the second the color of the stripe.
- Page 3 ELECTRICAL SYSTEM GENERAL PROCEDURES; continued Wire Tie Procedure 4.Trim wire tie end 2.Insert the Tapered 3.Pull the Tapered End 1.Wrap wire tie around after tightening. through the Wire Tie Head the harnesses you End of the wire tie into the Wire Tie until the wire tie is snug.
- Page 4 VEHICLE PREPARATION; continued b. Remove the driver’s side kick panel by removing the plas- tic nut. (FIGURE C) Partially peel back the rubber weatherstrip away from the kick panel. Insert a fiber stick Plastic Nut Plastic Nut between the body and kick panel to disengage the re- taining clip.
- Page 5 REMOTE START CONTROL MODULE PREPARATION 1. Insert the supplied fuses into the remote start control module as shown below. (FIGURE F) The fuses fit tightly, so use the flat tip of a fiber stick to push them in place, if necessary. 2.
- Page 6 DIPOLE ANTENNA MOUNTING A-PILLAR UPPER TRIM 1. Driver’s A-Pillar Trim Removal/Installation a. Partially peel back the rubber weatherstrip away from the A-pillar trim. b. Pull the A-pillar trim, then disengage clips A. (FIGURE K) CLIP B CLIP A c. Pull the A-pillar trim, then disengage clip B (Picture 1). GROMMET d.
- Page 7 HOOD SAFETY SWITCH MOUNTING 1. Using (2) supplied, 1/4” self drilling screws and (2) supplied lock washers, secure the hood safety switch to the drivers side of the vehicle’s hood 105 mm above the top of the hood mounting bracket and 70 mm from the side edge of the hood.
- Page 8 HOOD SAFETY SWITCH MOUNTING, continued 4. Using fish wire, pull the hood safety switch wiring and WHITE/BLACK tach wire from the re- mote start harness through the main wire harness grommet: a. From inside of the vehicle, bend approximately three (3) inches of tach wire at wire end. b.
- Page 9 HOOD SAFETY SWITCH WIRE CONNECTIONS 1. Locate the BLACK and GRAY/RED wires from the remote start harness. 2. Using the (2) supplied IDC wire taps (in hood safety switch parts bag), connect the wires listed below together and crimp the IDC wire taps in place using pliers. Ensure that a complete and secure connection is made.
- Page 10 WIRE HARNESS CONNECTIONS - STEERING COLUMN IGNITION SWITCH CONNECTOR 1. Route the remote start ignition harness with 6-pin male and fe- male ignition connectors over the factory harness, along the left side of the steering column. Do not secure harness at this time.
- Page 11 WIRE HARNESS CONNECTIONS - STEERING COLUMN, continued KEY-IN-SENSE & PUSH WIRE ROUTING 1. Route the remote start harness YELLOW/BLUE and BROWN/BLACK wires along with the im- mobilizer interface ribbon cable behind the vehicle’s steering column harness to protect the wires from any potential damage from the steering column cover and tilt and telescopic steer- ing wheel mechanism.
- Page 12 WIRE HARNESS CONNECTIONS - STEERING COLUMN, continued KEY-IN-SENSE CONNECTION 1. Locate the 12-pin (Smart-Key equipped) or 2-pin (Retractable Key equipped) WHITE key-in-sense connector under the igni- tion switch. (FIGURE AA) 2. Using a razor knife carefully cut back 1”-2” of the electrical tape to expose the wiring.
- Page 13 IMMOBILIZER INTERFACE RIBBON CABLE MOUNTING 1. Route the immobilizer interface ribbon cable to the ignition switch. 2. Following the instructions on the supplied adhesive primer stick, apply a thin coating to the outer surface of the immobilizer antenna coil (black plastic ring around ignition switch) and to the ribbon cable.
- Page 14 WIRE HARNESS CONNECTIONS - SECURING 1. Using (2) supplied, short wire ties, secure the remote start harness and immobilizer interface harness to the vehicle’s factory ignition wire harness. (FIGURE KK) NOTE: IT IS EXTREMELY IMPORTANT THAT THE WIRING IS SECURED IN A MANNER THAT WILL ALLOW THE TILT AND TELESCOPIC STEERING WHEEL TO MOVE FREELY AND STILL ALLOW FOR REASSEMBLY OF THE STEERING COLUMN SHROUD.
- Page 15 WIRE HARNESS CONNECTIONS - DRIVER’S KICK PANEL, continued DOME LIGHT CONNECTION 1. Locate the 6-pin WHITE connector at the Body Control Module mounted in the left kick panel area. (FIGURE PP) 6-pin 2. Using a razor knife carefully cut back 1”-2” of the electrical tape to expose the wiring.
- Page 16 WIRE HARNESS CONNECTIONS - ENGINE COMPARTMENT TACHOMETER CONNECTION 1. Locate the upper 66-pin BLACK (2007 - 2010 Models) or the middle 70-pin BLACK (2011 Models) connector at the Powertrain Control Module mounted to the backside of the driver’s side strut tower in the engine compartment. (FIGURE TT) 2.
- Page 17 EMERGENCY OVERRIDE/PROGRAMMING BUTTON MOUNTING 1. Locate the previously removed driver’s side kick panel cover. 2. Drill a 9/32” hole at the top of the panel, exactly 12 mm down and 95 mm from the far edge. 3. Route the emergency override/programming button from the remote start harness down to the kick panel.
- Page 18 RE-ASSEMBLY, continued f. Re-install the driver’s side scuff plate by engaging all three clips. (FIGURE ZZ) FIGURE ZZ 2. Re-install and Reconnect Battery: a. Carefully re-install battery into vehicle’s battery tray. b. Re-install battery hold-down bracket by engaging lower retainers into battery tray, away from vehicle dashwall and tightening both 10 mm nuts to 78-121 inch/pounds.
- Page 19 TACHOMETER PROGRAMMING 1. Tachometer Programming - Make sure engine hood is closed! a. Turn the ignition key to the RUN position. b. Press and hold the programming button. After 10 seconds the horn will beep 3 times. c. Release the programming button. d.
- Page 20 IMMOBILIZER INTERFACE PROGRAMMING NOTE: THE TACHOMETER SIGNAL MUST BE PROGRAMMED TO THE DNA CARD FOR THE REMOTE ENGINE START FUNCTION TO OPERATE. (READ ENTIRE PROGRAMMING PROCEDURE PRIOR TO PROGRAMMING.) 1. Transponder interface programming: NOTE: Two programmed ignition keys are required for this step and engine hood must be closed. For Smart-Key equipped vehicles, remove keys from Smart-Key transmitters and place transmit ters at least 10 feet away from vehicle during programming.
- Page 21 FUNCTION TEST Car Find 1. Press and hold START button - Horn should beep six times and parking lights should flash six times. Remote Engine Start Functions 1. REMOTE ENGINE START - Make sure the key is removed from the ignition switch and the engine hood is closed.
- Page 22 TROUBLESHOOTING GUIDE 1. Horn honks 4 times & vehicle does not remote start - No tachometer signal learned to DNA card. a. Ensure good connection and correct vehicle wire at PCM in engine compartment (See Section 13). b. Re-program tachometer signal (See Section 18). 2.
- Page 23 TROUBLESHOOTING GUIDE, continued 9. Vehicle’s Perimeter Alarm sounds during remote start operation. a. Ensure remote start dome light fuse is placed in the (+) positive position (See Section 2). b. Ensure the Yellow/Blue remote start wire is routed properly and is not cut or shorted on any vehicle components (See Section 8).
- Page 24 Hood Safety Switch Kit Service Part 0000-8F-H05A Mazda Immobilizer Interface Service Part 0000-8F-M21 Mazda CX-7/CX-9 DNA Card Software Service Part 0000-8F-N18A Mazda CX-9 Remote Start Wire Harness Service Part 0000-8F-Z01 Remote Start Control Module Service Part 0000-8F-Z02 Mazda 1-Button Remote Start Transmitter Service Part 0000-8F-Z03...
- Page 25 4280159 Rev. A 10/10...
- Page 26 FINAL INSPECTION • Inspect the installed / reinstalled parts for the following items: Inspection Items ( ) Installation / Inspection Parts Scratches / Dirt / Clearance / Fit Tightening / Operation Check Harness Interference Engagement Negative battery terminal and battery hold downs Driver-side scuff plate Driver-side door seal...