Advertisement
Quick Links
NOTE: BOTH PROGRAMMED
IGNITION KEYS ARE REQUIRED
AT TIME OF INSTALLATION
PART NUMBER (s):
& L10A
0000-8F-L10
HOOD SAFETY SWITCH KIT CONTENTS
(P/N: 0000-8F-H03)
Hood Safety
1/4" Self
Switch
Drilling Screws
(QTY 1)
(QTY 2)
Tie Wrap
IDC Wire Tap
(QTY 2)
(QTY 2)
IMMOBILIZER INTERFACE KIT CONTENTS
(P/N: 0000-8F-H05)
Immobilizer Interface
Adhesive Primer
Module and Harness
(QTY-1)
TOOLS REQUIRED
SAFETY GLASSES
ELECTRICAL TAPE
WIRE CUTTERS
PLIERS
ALCOHOL or GLASS CLEANER
PHILLIPS SCREWDRIVER
POWER DRILL
9/32" DRILL BIT
FIBER STICK
10mm SOCKET AND RATCHET
1/4" SOCKET AND DRIVE
3/8" DRIVE TORQUE WRENCH
3/8" DRIVE 10mm SOCKET
1
VEHICLE PREPARATION
1. Disconnect negative battery terminal:
a. Remove relay cover by grasping rear of cover and pulling upwards.
Disengage locking tabs and remove cover. (FIGURE A)
b. Disengage locking tabs and remove cover the battery cover.
c. Disconnect negative battery terminal and isolate.
GENUINE ACCESSORIES
INSTALLATION INSTRUCTIONS
REMOTE START SYSTEM
WITH VEHICLE SECURITY
AND KEYLESS ENTRY
Remote Start
Locking
Control Module
Washer
(QTY-1)
(QTY 2)
P/N: 0000-8F-Z01
MAZDA
GENUINE ACCESSORIES
Vehicle Remote Start System
Owner's Manual
Featuring PowerCode Technology
For the Ultimate in Comfort, Convenience and Security
TM
Owners
Manual
(QTY 1)
2- Sided Tape
(QTY-1)
(QTY-1)
0
KIT CONTENTS
DNA Card
(QTY-1)
P/N: 0000-8F-L16
2 sec.
5X
2 sec.
30
TM
sec.
Wallet
Card
(QTY 1)
(QTY 1 / 0000-8F-Z12)
PARTS BAG CONTENTS
Tie Wrap
(QTY-10)
PRE INSTALLATION
1. CLEAN HANDS
2. OPEN DRIVER'S DOOR WINDOW
3. RECORD RADIO STATIONS
4. SET PARKING BRAKE
5. DISCONNECT AND ISOLATE
NEGATIVE BATTERY TERMINAL
6. VEHICLE MUST BE AT ROOM
TEMPERATURE
1
®
APPLICABLE MODELS:
2004>MAZDA3
All Models With
Power Door Locks
LOCK
UN
LOCK
START
Remote Start
Dipole Antenna
Transmitters
(QTY-1)
(QTY-2)
P/N: 0000-8F-F06
P/N: 0000-8F-Z10
WARNING: / AVERTISSEMENT
This vehicle is equipped with a remote controlled engine starter.
To reduce the risk of serious Injury or death, switch engine starter
system into service mode and disconnect the vehicle battery
before performing any service on the vehicle.
Ce véhicule est doté d'un démarreur à distance. Pour réduire les
risques de blessures graves ou mortelles, mettre le démarreur à
distance en mode service et débrancher la batterie du véhicule
avant d'effectuer des travaux d'entretien sur celui-ci.
Underhood
Long Tie
Wrap
Sticker
(QTY 1)
(QTY 3)
0000-8F-D19
LED
(QTY-1)
FIGURE A
1031012 Rev.A 09/05
Remote Start
Wire Harness
(QTY-1)
P/N: 0000-8F-L02
Mini Fuses
(QTY - (1) 5 AMP)
(QTY - (7) 15 AMP)
IDC Wire Tap
(QTY-7)
Advertisement
Related Manuals for Mazda 3 2004
Summary of Contents for Mazda 3 2004
- Page 1 P/N: 0000-8F-Z01 P/N: 0000-8F-L16 P/N: 0000-8F-F06 P/N: 0000-8F-Z10 P/N: 0000-8F-L02 MAZDA GENUINE ACCESSORIES WARNING: / AVERTISSEMENT Vehicle Remote Start System This vehicle is equipped with a remote controlled engine starter. To reduce the risk of serious Injury or death, switch engine starter Owner's Manual 2 sec.
- Page 2 VEHICLE PREPARATION, continued 2. Remove the following components: a. Using a fiber stick remove the driver’s side scuff plate. b. Remove the driver’s side kick panel by using a fiber stick FIGURE B pull the plastic center button of the plastic fastener out to dis- engage (FIGURE B).
-
Page 3: Dipole Antenna Mounting
DIPOLE ANTENNA MOUNTING 1. Clean mounting spot with an alcohol pad prior to mounting. Mount the dipole antenna to the windshield 210mm to the right of center on the windshield, directly below the black windshield trim material. (FIG- URE J) FIGURE J 2. - Page 4 HOOD SAFETY SWITCH MOUNTING CONTINUED 5. Locate the hood release cable grommet from inside the occupant compartment. (FIGURE R) 6. Pull the hood release cable and grommet approximately 20” into the driver’s side footwell. (FIGURE S) 7. Using fish wire, pull the hood safety switch wiring through the hood release cable opening: a.
- Page 5 REMOTE START CONTROL MODULE PREPARATION 1. Insert the supplied fuses into the remote start control module as shown in below (FIGURE W). the fuses fit tight so use a tool handle to seat them in place if necessary. 2. Install DNA card into the remote start control module as shown below. (FIGURE X) NOTE: Use care to assure that both rows of the multipin connectors are aligned and seated properly.
- Page 6 HOOD SAFETY SWITCH MOUNTING WIRE CONNECTIONS 1. Locate the BLACK/ORANGE and GRAY/RED wire from the remote start system harness. 2. Locate the wires listed below. If the hood safety switch wire has a ground ringlet terminal or a stripped end on either wire then cut the ends of the wires so they are blunt.
- Page 7 1031012 Rev.A 09/05...
- Page 8 WIRE HARNESS CONNECTIONS- STEERING COLUMN IGNITION SWITCH CONNECTOR 1. Spot tape the immobilizer interface ribbon cable wiring to the ignition harness making sure to leave enough slack to route over to the igni- tion switch on the right side of the steering column. 2.
- Page 9 IMMOBILIZER INTERFACE RIBBON CABLE MOUNTING 1. Route the immobilizer interface (previously installed) ribbon cable to the ignition switch, making sure to keep it away from any moving parts. 2. Following the instructions on the supplied ampule of adhesive primer, apply a thin coating to the entire transceiver antenna ring (black plastic ring around key switch, FIGURE II) and to the ribbon cable.
- Page 10 WIRE HARNESS CONNECTIONS- BRAKE SAFETY 1. Locate the brake switch connector mounted to the brake pedal assembly. 2. Temporarily unplug the connector from the brake switch and carefully remove 1”-2” inches of tape covering the harness. 3. Place (1) supplied IDC wire tap on to the vehicle wire (using the side of the IDC wire tap that is open on both ends).
- Page 11 WIRE HARNESS CONNECTIONS- PASSENGER UNDERDASH, continued BLUE (J-04) CONNECTOR-TOP OF PJB 1. Locate the blue (J-04) connector on the top side of the PJB. (FIGURE OO) 2. Place one (1) IDC wire tap on each of the vehicle wires listed below (using the side of the IDC wire tap that is open on both ends).
- Page 12 LED MOUNTING 1. Locate a blank knockout switch panel on the lower dashboard panel. 2. Drill a 9/32” hole in the knockout switch panel, making sure the hole is centered approximately 10mm from side edge and 5mm from top. (FIGURE RR) 4.
-
Page 13: System Power-Up
RE-ASSEMBLY 2. Re-install the following components: a. Re-install the lower center console kick panels on both driver and passenger sides. Re-secure the plastic fas- tener on both. (FIGURE TT) FIGURE TT b. Re-install the steering column shroud by first securing the ignition key light in place and then snapping the (2) FIGURE UU halves of the steering column shroud together. -
Page 14: Function Test
IMMOBILIZER INTERFACE PROGRAMMING NOTE: IF YOU DID NOT START THE CAR WITH THE IGNITION KEY AS INSTRUCTED TO IN SECTION 15 STEP 5 THEN THE VEHICLE WILL NOT ATTEMPT TO START, INSTEAD YOU WILL GET THREE ADDITIONAL BEEPS FROM THE HORN. THE VEHICLE HAS TO BE STARTED AT LEAST ONCE WITH THE KEY FOR THE REMOTE ENGINE START FUNCTION TO OPERATE. - Page 15 FUNCTION TEST, continued Progressive Car Find® 1. Press the PANIC BUTTON once - Horn should beep five times and parking lights should flash five times. 2. Press the PANIC BUTTON a second time - Horn should beep five times but sound a little louder and parking lights should flash five times.
-
Page 16: System Programming
SYSTEM PROGRAMMING NOTE: THE FOLLOWING STEPS ARE ONLY NECESSARY IF YOU NEED TO PROGRAM ADDITIONAL TRANSMITTERS OR TO ENTER THE OPTION MODE TO TURN ON AND SET THE SENSITIVITY OF THE SHOCK SENSOR. 1. Transmitter Programming: NOTE: The transmitters shipped with the remote start system are pre-programmed to the DNA card, and do not need to be reprogrammed. - Page 17 Shock Sensor Testing Rearm the security system and test the shock sensor. This system is equipped with a two stage shock sensor which has a lite-touch (warn away) trigger and a full trigger. The lite-touch trigger senses for non-damaging shock to the vehicle and beeps the horn, the full trigger senses for potential damaging shock to the vehicle and triggers the security system.
- Page 18 1031012 Rev.A 09/05...
- Page 19 1031012 Rev.A 09/05...