Table of Contents
Advertisement
GENUINE Mazda Mobile Start
INSTALLATION INSTRUCTIONS
Thank you for purchasing a genuine Mazda accessory.
Before removal and installation, be sure to thoroughly read these instructions. Please read the contents of this
booklet in order to properly install and use the Mazda Mobile Start. Your safety depends on it.
Keep these instructions with your vehicle records for future reference.
•
There are several
Warning and
removing the Mazda Mobile Start. Always read and follow them in order to prevent injuries, accidents, and possible
damage to the vehicle.
WARNING:
Indicates a situation in which serious injury or death could result if the warning is ignored.
CAUTION:
Indicates a situation in which bodily injury or damage to the vehicle could result if the caution is ignored.
•
For areas indicating the tightening torque in this instruction manual, tighten to the specified torque using a torque wrench. For
areas in which the tightening torque is indicated inside parentheses ( ), the tightening torque is indicated as a reference value,
however tightening using a torque wrench is not necessary.
•
Do not modify the Mazda Mobile Start.
•
Do not install the Mazda Mobile Start in any way other than described in the following instructions.
•
If in any doubt, please ask your Mazda dealer to install the accessory in order to prevent errors in installation.
•
If you have any questions about the use of the accessory, ask your Mazda dealer for proper advice before using it.
•
Mazda and its suppliers are not responsible for injuries, accidents, and damage to persons and property that arise from the
failure of the dealer or installer to follow these instructions.
•
To ensure safety and reliability of the work, installation, removal and disposal work must carried out by an Authorized Mazda
Dealership.
•
Be careful not to lose removed parts, and be sure that they are kept free from scratches, grease or other dirt.
NOTE
To the dealer
• Please turn over these instructions to the customer after installation.
To the customer
• Keep these instructions after installation. The instructions may be necessary for
installing other optional parts or removal of this accessory.
• Should the vehicle or this accessory be resold, always leave these instructions
with it for the next owner.
WARNING
CAUTION sections in this booklet concerning safely when installing or
PART NAME :
VEHICLE :
PART NUMBER :
1
Mazda Mobile Start (MMS)
Mazda CX-3 / Mazda2
0000-8F-Z80 (MMS ECU Kit)
0000-8F-P07 (MMS Harness Kit)
[KD53-V7-629 (Hood Switch)]
090003-33280700
Advertisement
Table of Contents
Related Manuals for Mazda 0000-8F-Z80
Summary of Contents for Mazda 0000-8F-Z80
- Page 1 If in any doubt, please ask your Mazda dealer to install the accessory in order to prevent errors in installation. • If you have any questions about the use of the accessory, ask your Mazda dealer for proper advice before using it. •...
- Page 2 1. INSTALLATION VIEW (Sold separately) Hood switch (Only for vehicles without theft-deterrent or without i-ELOOP system) GPS Antenna TEL Antenna GPS & TEL Antenna Cables Harness (GND) MMS Harness MMS ECU RES Diagnostic Connectors MMS 2P Connector Connector...
- Page 3 2. PARTS Note • Verify that the kit includes all the following parts and that they are free of dirt, scratches, or damage. MMS ECU KIT (Part no. 0000-8F-Z80) Part Part Name Qty. Part Part Name Qty. Part Part Name Qty.
-
Page 4: Required Tools
3. BEFORE INSTALLATION REQUIRED TOOLS • 10mm Socket Wrench • Scissors • Torque Wrench • Taped Flathead Screwdriver • Mat • Electrical Tape • Panel Removal Tool • Soft clean cloth • Squeegee • Glass Cleaner • Nipper • Pliers •... - Page 5 RES Connector RDIG GND (M6) Connector to Connector VEHICLE CONNECTOR MMS Wire 20XX- MAZDA MAZDA MOBILE START (MMS) Vehicle Wire CONNECTORS Scotch lock connection MMS or Vehicle Terminal Insert (TERMINAL PIN) ( FEMALE PIN ) (FEMALE PIN) ( FEMALE PIN )
- Page 6 6. VEHICLE DISASSEMBLY Note • Be careful not to damage or lose any parts removed from the vehicle since they will be reused. Place the vehicle in park with the parking brake set. Negative battery terminal Disconnect negative battery terminal and wrap tape around it to insulate.
- Page 7 Glove box removal Push both sides of the Glove box then pull to dislodge 2 Hooks (B). Remove the Glove box by pulling to dislodge 2 bottom Hook B Hooks (C). Hook C Vehicle Front Vehicle front Remove Glove box under cover in order of arrows (1-3). Hook A Guide C Pin B...
- Page 8 Passenger side lower panel removal Remove 3 Screws and 1 Bolt. Screws Bolt tightening torque: 2.0 - 6.0 N•m (1.5 - 4.4 ft•lbf) Vehicle front Screw Vehicle Front Bolt Remove lower panel by pulling in the order of arrows (1-4). Clips Clip Clips Clip Vehicle front Vehicle Front A-Pillar trim removal Clip B Clip B Partially peel back the seaming welt.
- Page 9 Remove the Grommet from the A-pillar by using a flat Grommet Grommet Hook A-pillar head screwdriver by following sequence (1) - (3). inner panel Grommet Install the new supplied A-pillar tether clip into A-pillar trim before proceeding. Caution Tape-wrapped flathead screwdriver Tape-wrapped athead screwdriver • Ensure the new supplied tether clip is used in step 6.
- Page 10 While pressing the tab, lift the relay and fuse block cover to remove it. Vehicle Front Relay and fuse block cover Install the Hood switch to the hood latch and secure it using the supplied Screw. Hood Latch Wire Tie (Black) Hook the Hood switch harness to the Hood latch and Vehicle Front secure it using a wire tie (black).
- Page 11 CX-3 CX-3 Hood switch harness Route the hood switch harness along the vehicle wiring harness and secure it with 3 wire ties (black). Vehicle wiring harness clip 3 x Wire Ties (Black) Vehicle wiring harness clip Vehicle Front Shroud panel Mazda2 Mazda2 Hood switch harness...
- Page 12 2 x Wire Ties (Black) Vehicle wiring harness Vehicle Front 8. MAZDA MOBILE START INSTALLATION GPS and TEL Antenna Installation Place the Antenna template face down on the windshield outside the vehicle, aligning to the passenger side A-pillar and the top right corner with the headliner temporarily secure it with electrical tape.
- Page 13 Caution Blue Tab GPS Film • Use glass cleaner to clean the inside windshield attachment Antenna Headliner Headliner surface indicated by the template before attaching the GPS/ TEL Film Antennas. Green Tab Use the Blue tab to remove the partial protective backing GPS Film Antenna from the GPS Film Antenna.
- Page 14 Use no. 2 tab to slowly peel off the remaining protective backing while using a squeegee to attach the TEL Film Squeegee Squeegee Protective Backing Protective Backing Antenna on the windshield. No. 2 Tab Caution • Make sure to use a squeegee when attaching the GPS Film Antenna on the windshield to eliminate any air bubbles.
- Page 15 15. Cut another 1/2 piece of urethane foam tape, then wrap the TEL Connector Cable 50mm away from the TEL Connector. TEL Connector 1/2 Urethane Foam tape 50mm 50mm 16. Peel the protective backing off the TEL Connector. 17. Attach the TEL Connector making sure to align to the TEL Film Antenna line guide.
- Page 16 20. Cut the FH Protection sheet in half. 1/2 FH Protection sheet 21. Wrap the Antenna cables starting from the bottom of the A-pillar using the 2 pieces of 1/2 FH Protection sheet. 22. Secure the FH Protection sheet using electrical tape. 1/2 FH Protection sheet 23.
- Page 17 29. Plug in MMS harness 2P connector to Vehicle Harness 2P Pre-connector. Note • The 2P Pre-connector is located either in front or back of the vehicle harness depending on vehicle specs. MMS 2P MMS 2P Connector Connector 2P Pre-connector in 2P Pre-connector in back of Vehicle harness front of Vehicle harness...
- Page 18 36. Plug in the MMS harness 24P connector, TEL and GPS connectors to the MMS ECU. GPS 1P Connector TEL 1P Connector MMS Harness 24P Connector Vehicles without protective pad on glove box undercover 3 x Double-sided (Steps 37 to 41) adhesive tapes (25 x 25 mm) 37.
- Page 19 Vehicles with protective pad on glove box undercover Protective Pad (Steps 42 to 50) 3 x Double-sided adhesive tapes (25 x 25 mm) 42. Peel off part of the protective pad and clean off adhesive residue from the glove box undercover. Caution •...
- Page 20 51. Bundle up the excess Antenna Cables and secure with Electrical tape. 52. Secure the bundled up Antenna Cable to the vehicle harness using 2 wire ties (white). GPS & TEL Vehicle Antenna Cables harness 2 x Wire Ties (White) Electrical tape 53.
- Page 21 9. MMS REGISTRATION PROCEDURE Make sure of the following conditions: In possession of 2 Advanced Keys that are already registered to the vehicle. Do not open any doors during MMS registration procedure. Response Response Steps MMS Registration Procedure when when it fails successful Connect the negative battery cable and close the hood.
- Page 22 10. MMS CHECK MODE The following procedure is performed to verify MMS operation after MMS registration. Make sure that MMS Registration was successful prior to proceeding. MMS check mode preparations: Place 1 Advanced Key at least 5 feet away from the vehicle and keep 1 Advanced key in your possession. Close the hood, enter the vehicle's passenger side and leave the door open.
- Page 23 11. REINSTALLATION / INSPECTION Disconnect the LED from the MMS Harness and discard MMS harness Secure MMS harness LED connector to the vehicle harness with 1 wire tie (white). Secure the RES Diagnostic connectors to the vehicle harness with 1 wire tie (white). RES Diagnostic 2 x Wire Ties (White) Connector...
- Page 24 Date: VIN: Mazda Mobile Start (MMS) INSTALLATION Mazda CX-3 0000-8F-Z80 (MMS ECU Kit) INSPECTION Mazda2 0000-8F-P07 (MMS Harness Kit) SHEET KD53-V7-629 (Hood Switch) Perform the following inspections. WARNING • Before starting the engine, make sure there are no persons in front of or behind the vehicle, or around the engine compartment.