Related Manuals for Advantech UNO-3072LA
Summary of Contents for Advantech UNO-3072LA
- Page 1 UNO-3072LA Intel Atom Embedded Automation Computer with Two PCI Slot Extensions User Manual...
-
Page 2: Copyright Notice
No part of this man- ual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reli- able. - Page 3 Product Warranty (2 years) Advantech warrants to you, the original purchaser, that each of its prod- ucts will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products which have been repaired or...
- Page 4 This product has passed the CE test for environmental specifications when shielded cables are used for external wiring. We recommend the use of shielded cables. This kind of cable is available from Advantech. FCC Class A This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
- Page 5 Safety Instructions Read these safety instructions carefully. Keep this User's Manual for later reference. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for clean- ing. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible.
- Page 6 The sound pressure level at the operator's position according to IEC 704- 1:1982 is no more than 70 dB (A). DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech disclaims all responsibility for the accuracy of any statements contained herein. Safety Precaution - Static Electricity Follow these simple precautions to protect yourself from harm and the products from damage.
-
Page 7: Table Of Contents
Figure 1.1:Chassis Dimensions ........5 Packing List............... 6 Chapter 2 Hardware Functionality ....... 10 Introduction ..............10 Figure 2.1:Front Panel of UNO-3072LA ..... 10 RS-232/422/485 Interface (COM1~COM2) ....11 2.2.1 16C950 UARTs with 16-byte FIFO Standard ..... 11 2.2.2 RS-422/485 Jumperless Detection ....... 11 2.2.3... - Page 8 Rubber Foot Installation..........34 Appendix A System Settings and Pin Assignments ..36 System I/O Address and Interrupt Assignments ..36 Table A.1:UNO-3072LA System I/O Port ....36 Table A.2:UNO-3072LA Interrupt Assignments ..37 Board Connectors and Jumpers........38 Figure A.1:Backplane Connector & Jumpers ....38 Figure A.2:Mainboard Connector &...
- Page 9 Table of Contents...
- Page 10 UNO-3072LA User Manual...
- Page 11 Overview This chapter provides an overview of UNO-3072LA specifications. Sections include: • Introduction • Hardware specification • Safety precautions • Chassis dimensions...
-
Page 12: Chapter 1 Overview
The Gigabit LAN supports the teaming function with fault tolerance, link aggregation, and load balancing. Different from general industrial PCs, UNO-3072LA is more compact and reliable with a fanless and cableless design. It was designed with an open platform which can fulfill demand- ing requirements, and it is an ideal solution for industrial automation and control. - Page 13 • Compact Flash Slots: Two type I/II CompactFlash Slots, One internal and one external • HDD: SATA HDD extension kit for one standard 2.5" HDD One external eSATA device (Does not support hot swap) • LEDs: Power, Standby, HDD, 4 COM ports Tx /Rx, LAN (Active, Status) (Optional: 4x Programmable LED while COM ports Tx/Rx disable) •...
-
Page 14: Safety Precautions
Note: Always ground yourself to remove any static elec- tric charge before touching UNO-3072LA. Modern electronic devices are very sensitive to static elec- tric charges. Use a grounding wrist strap at all times. Place all electronic components on a static- dissipative surface or in a static-shielded bag. -
Page 15: Chassis Dimensions
1.4 Chassis Dimensions 238.00 139.60 Figure 1.1: Chassis Dimensions Chapter 1... -
Page 16: Packing List
1.5 Packing List The accessory package of UNO-3072LA contains the following items: (A) SATA signal cable and power cable (B) Warranty card (C) Driver and Utility CD-ROM (D) 2 x Anti-vibration rubber (E) Mini Jumper (F) Paper menu (G) Power connector... - Page 17 Chapter 1...
- Page 18 UNO-3072LA User Manual...
- Page 19 Hardware Functionality This chapter shows how to setup the UNO-3072LA hardware functions, including connecting peripherals, and setting switches and indicators. Sections include: • Introduction • RS-232 Interface • RS-232/422/485 Interface • LAN / Ethernet Connector • Power Connector • LED and Buzzer •...
-
Page 20: Chapter 2 Hardware Functionality
Chapter 2 Hardware Functionality 2.1 Introduction The two figures below show the connectors on UNO-3072LA, and follow- ing sections give you detailed information about function of each periph- eral. 139.60 Figure 2.1: Front Panel of UNO-3072LA UNO-3072LA User Manual... -
Page 21: Rs-232/422/485 Interface (Com1~Com2)
RS-422 or RS-485 networks. (Refer to section 2.2.5) 2.2.3 Automatic Data Flow Control Function for RS-485 In RS-485 mode, UNO-3072LA automatically detects the direction of incoming data and switches its transmission direction accordingly. So no handshaking signal (e.g. RTS signal) is necessary. This lets you easily build an RS-485 network with Data+, Data- and Ground. - Page 22 Jumper setting for RS-422/485 interface: (Default setting). Figure 2.2: RS-422/485 Jumper Setting Jumper setting for RS-232 interface: Figure 2.3: RS-232 Jumper Setting UNO-3072LA User Manual...
-
Page 23: Terminal Resistor Setup For Rs-422/485
2.2.5 Terminal Resistor Setup for RS-422/485 The onboard termination resistor (120 Ohm) for COM1/COM2 can be used for long distance transmission or device matching (Default Open). Each terminal resistor responds to different channels for RS-422/485. Usually, these resistors are needed for both ends of the communication wires and the value of the resistors should match the characteristic imped- ance of the wires used. -
Page 24: Rs-485 Auto Flow/Rs-422 Master/Slave Selection
Then no handshaking is necessary. UNO-3072LA can also allow user to adjust "Master/Slave" mode of RS- 422 by changing setting in BIOS for each RS-422/485 port COM1 &... -
Page 25: Optional Rs-232 Interfaces (Com3~Com4)
2.3 Optional RS-232 Interfaces (COM3~COM4) UNO-3072LA offers two optional RS-232 serial communication inter- faces: COM3 and COM4. Please refer to Appendix A.4 for their pin assignments. The default of these two COM ports is "Disabled". In order to use these two COM ports, follow these steps: Purchase the UNO-IO80-AE optional cable kit. - Page 26 Change the IRQ and IO address from Disablde to the above setting. Press F10 or Back to "Save and Exit Setup" to finish setup change. Fasten the COM port bracket on the UNO-3072LA system . The IRQ and I/O address range of COM3 and COM4 are listed below:...
-
Page 27: Lan: Ethernet Connector
2.4 LAN: Ethernet Connector The UNO-3072LA is equipped with a Intel 82574L Ethernet LAN con- troller that is fully compliant with IEEE 802.3u 10/100Base-T CSMA/CD standards. The Ethernet port provides a standard RJ-45 jack on board, and LED indicators on the front side to show its Link (Green LED) and Active (Y ellow LED) status. - Page 28 LED". Press F10 or Back to "Save and Exit Setup" to finish setup change. Table 2.2: LED Control Register 212H Diagnostic / Programmable LED Register Note: Px: = 0, DIAG LED disable = 1, DIAG LED enable UNO-3072LA User Manual...
-
Page 29: Usb Connector
A.10. 2.7.1 VGA Support and Hotkey UNO-3072LA support VGA interface: CRT mode: 1280 x 1024 @ 32bpp (60Hz), 1024 x 768 @ 32bpp (85Hz) and supports 8 MB frame buffer with system memory. You can set the hotkey and other configuration for the VGA Graphics. -
Page 30: Multiple Video Output Option
"CTRL+ALT+F1" in order to manually switch video output. 2.7.2 Multiple Video Output Option UNO-3072LA provides a single DVI-I connector, which lets users have multiple video output configurations: Single Display:... -
Page 31: Reset Button
Dual Display: In order to support Dual display, you will need to purchase the DVI-I con- vertion cable to DVI-D and VGA (p/n:1700004713). You could link you DVI or VGA monitor through DVI-I to DVI and VGA cable. Note: Be sure to check the resolution that monitor support first and only use the resolution support by monitor. -
Page 32: Power Button
2.9 Power Button UNO-3072LA standard power is ATX type. Please press the "Power" but- ton to power on or power off. The power switch bottom featured "safety switch" which user need to use finger tip to continue press 4 second to shut the system down. - Page 33 Initial Setup This chapter introduces how to initialize the UNO-3072LA. Sections include: • Introduction • Inserting a CompactFlash Card • Chassis Grounding • Connecting Power • Connecting a Hard Disk • BIOS Setup and System Assignments...
-
Page 34: Chapter 3 Initial Setup
Screw back the top cover with four screws. 3.2 Connecting Power Connect the UNO-3072LA to a 9 ~ 36 VDC power source. The power source can either be from a power adapter or an in-house power source. UNO-3072LA User Manual... -
Page 35: Installing A Hard Disk
3.3 Installing a Hard Disk The procedure for installing a hard disk is listed below. Please follow these steps carefully. Remove the power cord. Unscrew the six screws from the bottom cover (as shown below) Unscrew the HDD bracket from the upper cover. Chapter 3... - Page 36 SATA hard drive connector like below. SATA HDD Installation Install HDD into HDD bracket and fix with screw Connect SATA cable and SATA power cable on HDD side and motherboard side. The correct connection way is shown below. UNO-3072LA User Manual...
- Page 37 Re-fasten the upper cover with the six screws. Chapter 3...
-
Page 38: Installing A Pci-Bus Card
3.4 Installing a PCI-bus Card The procedure for installing a PCI-bus card into the UNO-3072LA is listed below. Please follow these steps carefully. Remove the power cord. Remove the upper cover of UNO-3072LA. Unscrew the screw of a PCI bracket, and remove it. - Page 39 Plug-in PCI-bus card in a PCI-slot of UNO-3072LA. Chapter 3...
- Page 40 Screw back the upper cover with the eight screws. 7. Unscrew the two screws and take the PCI Anti-vibration support ki from accessory box UNO-3072LA User Manual...
- Page 41 8. Insert the PCI Anti-Vibration support kit through the hole shown till it insert tight. Cut the overhang part and fasten screws. Chapter 3...
-
Page 42: Mounting Uno-3072La
3.6 Installing Power Cable UNO-3072LA provides an internal backup power source so that it can provide power for a PCI Blower, external video card that required addi- tional power or other external devices. You can use the power cable from accessory package (see section 1.5). -
Page 43: Bios Setup And System Assignments
SOM-6761. Y ou can find this manual on the driver and utility DVD of UNO-3072LA in the accessory package. Please note that you can try to “LOAD BIOS DEFAULTS” from the BIOS Setup manual if the UNO-3072LA does not work properly. Chapter 3... - Page 44 3.8 Rubber Foot Installation UNO-3072LA provides Rubber Foot for two purpose: <1> Anti-Shock/ Vibration purpose and <2> protect the surface of Chassis from scratch. Please find the rubber foot in accessory box shown below. Please peel the non-stick paper and put the rubber foot on the location that has been circled in red.
- Page 45 System Settings and Pin Assignments...
-
Page 46: Appendix A System Settings And Pin Assignments
Appendix A System Settings and Pin Assignments A.1 System I/O Address and Interrupt Assignments Table A.1: UNO-3072LA System I/O Port Address Device Range Device 0000 - 0CF7 PCI bus 0000 - 000F Direct memory access controller 0020 - 0021 Programmable interrupt controller... - Page 47 Intel SCH Family USB Universal Host Controller - 8114 FF00 - FF07 Intel Corporation US15 Embedded Graphics Watchdog timer DC000-DFFFF Battery backup resource Table A.2: UNO-3072LA Interrupt Assignments Interrupt Number Interrupt source Parity error detected IRQ 0 System timer IRQ 1...
-
Page 48: Board Connectors And Jumpers
A.2 Board Connectors and Jumpers There are several connectors and jumpers on the UNO-3072LA board. The following sections tell you how to configure the UNO-3072LA hardware setting. Figures A.1 to A.5 show the location of the connectors and jump- ers. - Page 49 Table A.3: Connector and Jumper Descriptions Location Label Function Backplane FS1, FS2 Fuse for input DC power Dry Contact Selection Jumper CN15 Wet Contact Selection Jumper Hardware AT selection Jumper PCI frequency Selection (closed: 66MHz) CN13 3P Fan Power On (Closed: Always On) CN11, CN12 SATA power connector CN18...
- Page 50 DO status after reset Jumper CN28, COM port RS-232/RS-422&485 selection CN29 CN30 COM1/COM2 DB-9 connector CN33 3P Fan power connector CN39 Video detect Jumper for Dual DVI-D selection (Close:Disable VGA) CN41 Optional Cable Wired USB pin header CF1/CF2 Master selection (Reserved) UNO-3072LA User Manual...
-
Page 51: Rs-232 Standard Serial Port (Com3~Com4)
A.3 RS-232 Standard Serial Port (COM3~COM4) Table A.5: RS-232 Serial Port Pin Assigns RS-232 Signal Name Appendix A... -
Page 52: Rs-232/422/485 Serial Port (Com1~Com2)
A.4 RS-232/422/485 Serial Port (COM1~COM2) Table A.6: RS-232/422/485 Serial Port Pin Assigns RS-232 RS-422 RS-485 DATA- DATA+ A.5 Ethernet RJ-45 Connector (LAN1~LAN2) Table A.7: Ethernet RJ-45 Connector Pin Assigns 10/100Base-T Signal Name XMT+ XMT- RCV+ RCV- UNO-3072LA User Manual... -
Page 53: Ps/2 Keyboard And Mouse Connector
A.6 Power Connector (PWR) Table A.8: Power connector pin assignments V+ (9~36V Field Ground A.7 PS/2 Keyboard and Mouse Connector Table A.9: Keyboard & Mouse Connector Pins Signal Name KB DATA MS DATA KB Clock MS Clock Appendix A... -
Page 54: Usb Connector (Usb1~Usb4 & Cn7)
A.8 USB Connector (USB1~USB4 & CN7) Table A.10: USB Connector Pin Assignments Signal Name Cable Color DATA- White DATA+ Green Black UNO-3072LA User Manual... -
Page 55: Vga Display Connector
A.9 VGA Display Connector DVI-I to DVI & VGA Cable or Converter Table A.11: VGA Adaptor Cable Pin Assignmen Signal Name Green Blue H-SYNC V-SYNC Appendix A... - Page 56 A.10 DVI-I Connector Table A.12: DVI-I connector pin assignment Signal Name TMDS_C2# TMDS_C2 CRT_DDC_CLK CRT_DDC_DATA MDVI_CLK MDVI_DATA VGAVSY TMDS_C1# TMDS_C1 VCC_DVI VGA Detect HP_DET TMDS_C0# TMDS_C0 TMDS_CK# TMDS_CK VGAR VGAG VGAB VGAHSY UNO-3072LA User Manual...
- Page 57 A.11 Clear CMOS (CN3) This jumper is used to erase CMOS data and reset system BIOS informa- tion. Follow the procedures below to clear the CMOS. 1. Turn off the system. 2. Close jumper CN3 (1-2) to clear CMOS . 3, Remove jumper CN3(1-2) 3.
- Page 58 A.12 External & Internal SATA Connectors Table A.14: External SATA connector pin assignment Signal name Table A.15: Internal SATA DATA Connectors (CN40) Signal name UNO-3072LA User Manual...
- Page 59 Table A.16: Internal SATA Power Connectors (CN41) Signal name +12V +12V Appendix A...
- Page 60 UNO-3072LA User Manual...
- Page 61 Programming the Watchdog Timer...
-
Page 62: Appendix B Programming The Watchdog Timer
After data entry, your program must refresh the watchdog timer by rewrit- ing the I/O port 443 (hex) while simultaneously setting it. When you want to disable the watchdog timer, your program should read I/O port 443 (hex). UNO-3072LA User Manual... - Page 63 The following example shows how you might program the watchdog timer in BASIC: 10 REM Watchdog timer example program 20 OUT &H443, data REM Start and restart the watchdog 30 GOSUB 1000 REM Y our application task #1, 40 OUT &H443, data REM Reset the timer 50 GOSUB 2000 REM Y our application task #2, 60 OUT &H443, data REM Reset the timer 70 X=INP (&H443) REM, Disable the watchdog timer...
- Page 64 UNO-3072LA User Manual...