POSIFLEX DT-207 series User Manual
POSIFLEX DT-207 series User Manual

POSIFLEX DT-207 series User Manual

Desktop terminal

Advertisement

Quick Links

DT-207 / 208 Series
Desktop Terminal
User's Manual
Rev. A0
FCC Notes:
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions manual, may cause interference
to radio communications. It has been tested and found to comply with limits for a Class
A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to
provide reasonable protection against interference when operated in a commercial
environment. Operation of this equipment in a residential area is likely to cause
interference in which case the user at his own expense will be required to take whatever
measures to correct the interference.
Warranty Limits:
Warranty terminates automatically when any person other than the authorized
technicians opens the machine. The user should consult his/her dealer for the problem
happened. Warranty voids if the user does not follow the instructions in application of
this merchandise. The manufacturer is by no means responsible for any damage or
hazard caused by improper application.
About This Manual:
Posiflex Technologies, Inc. has made every effort for the accuracy of the content in this
manual. However, Posiflex Technologies, Inc. will assume no liability for any technical
inaccuracies or editorial or other errors or omissions contained herein, nor for direct,
indirect, incidental, consequential or otherwise damages, including without limitation
loss of data or profits, resulting from furnishing, performance, or use of this material.
This information is provided "as is" and Posiflex Technologies, Inc. expressly
disclaims any warranties, expressed, implied or statutory, including without limitation
implied warranties of merchantability or fitness for particular purpose, good title and
against infringement.
The information in this manual contains only essential hardware concerns for general
user and is subject to change without notice. Posiflex Technologies, Inc. reserves the
right to alter product designs, layouts or drivers without notification. The system
integrator shall provide applicative notices and arrangement for special options utilizing
this product. The user may find the most up to date information of the hardware from:
http://www.posiflex.com or http://www.posiflex.com.tw or http://www.posiflexusa.com
All data should be backed-up prior to the installation of any drive unit or storage
peripheral. Posiflex Technologies, Inc. will not be responsible for any loss of data
resulting from the use, disuse or misuse of this or any other Posiflex product.
All rights are strictly reserved. No part of this documentation may be reproduced,
stored in a retrieval system, or transmitted in any form or by any means, electronic,
mechanical, photocopying, or otherwise, without prior express written consent from
Posiflex Technologies, Inc. the publisher of this documentation.
© Copyright Posiflex Technologies, Inc. 2009
All brand and product names and trademarks are the property of their respective holders.
Part 1
P/N: 13300900020

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DT-207 series and is the answer not in the manual?

Questions and answers

Summary of Contents for POSIFLEX DT-207 series

  • Page 1 About This Manual: Posiflex Technologies, Inc. has made every effort for the accuracy of the content in this manual. However, Posiflex Technologies, Inc. will assume no liability for any technical inaccuracies or editorial or other errors or omissions contained herein, nor for direct, indirect, incidental, consequential or otherwise damages, including without limitation loss of data or profits, resulting from furnishing, performance, or use of this material.
  • Page 2 ALERT TO OUR HONORABLE CUSTOMERS: l Please always read thoroughly all the instructions and documents delivered with the product before you do anything about it. Don’t take any premature action before you have a full understanding of the consequences. l This product contains inside a Lithium battery. Please always follow local environmental protection laws / regulations for disposal of used batteries and always replace only with battery of same type.
  • Page 3: Product Pictures

    INTRODUCTION PRODUCT PICTURES Front View Inside Front Door Front Top View Rear Top View I Left Side View Rear Top View II Rear View Bottom View Part 3...
  • Page 4: Parts Identification

    PARTS IDENTIFICATION Display unit (7” LCD panel for DT-207 / 8” LCD + Touch panel for DT-208) Keyboard area (stroke type in the picture) Front door Power indicator Power switch Front door latch CF memory card reader slot MSR slot Display unit back cover 10.
  • Page 5 Durable resistive type touch panel that endures 35 million touches min. at same spot for DT-208 Touch control functions: left/right button, double click, drag & draw Spill proof water resistant structure allowing easy cleaning Easy maintenance construction m) Support WinCE, WEPOS and Linux environment Various I/O ports supported, including: 1.
  • Page 6: Opening Cable Cover

    INSTALLATION GUIDES CAUTION: Before any installation or cable connection to the set, please always make certain that the system is turned off and the external power source to the set is removed to prevent electric hazard! Never touch any metal pin in the connectors or circuits to avoid high voltage hazard or electrostatic discharge damage unless the operator is well grounded.
  • Page 7 DC + 5V support to the COM port that the PD-201 is to be connected to according to Posiflex technical information. Please then open the cable cover and push at the 2 latches toward the...
  • Page 8 Have a qualified technician to set a DC + 5V support to the COM port that the PD-309 is to be connected to according Posiflex technical information if it is the RS232 interface model PD-309. The LCD customer display PD-309 or PD-309U can be attached to either rear corner of bottom plate.
  • Page 9: Cash Drawer Connection

    The RJ11 connector in connection area of the DT system can be used for controlling most of the common cash drawers available on the market. However, it is most recommended that the Posiflex CR-xxx0 (the fourth digit of the model number being “0” in each cash drawer series) be used for best compliance.
  • Page 10: Connecting Cables

    For DT systems preloaded with WEPOS on HDD, Posiflex provides recovery CD or DVD delivered with the desktop terminal for the preloaded operating system. The System Integrator shall take care of software restoration after OS recovered. A Posiflex supplied USB interface CDROM or COMBO Part 10...
  • Page 11: Operating System Installation

    PC veterans to accomplish such a task. Therefore, OS installation into a system without preloaded OS is highly discouraged. Posiflex Technologies, Inc. shall not be responsible for any technical support to questions arisen due to non- preloaded OS.
  • Page 12: Application Environment

    UPS function module option is installed. Battery replacement: In the preloaded WEPOS OS for a DT system, there is a built in utility Posiflex Power Switch Manager that will indicate the UPS battery status of the battery. When an installed UPS battery...
  • Page 13: Power On/Off

    is found to be disabled or when pop up warning message like this picture appears, please replace the used up UPS battery at power off as soon as possible. Emergency treatment: The battery is constructed maintenance free and leakproof. Its storage space in DT system also provides very good protection as long as the ambient temperature remains below 30°C and the ventilation of the DT system remains free.
  • Page 14 (the forced power off feature will not work in this mode). When using this feature, please make sure that the software application has the ability to power off the machine. In preloaded Windows, “Posiflex Power Switch Manager” in “Posiflex Tools” in the Program Files helps managing these functions.
  • Page 15: Display Issues

    “Power Management Setup” to prepare the system ready to respond to a COM port MODEM Ring or wake up call from an operating caller system connected through LAN to the system. It requires a qualified networking technician to check the LAN chip ID of the system for the caller system to wake the destination system up.
  • Page 16: Rfid (Option)

    MSR (OPTION) The MSR option if installed is located in between the programmable keyboard and the display unit. There is a mark aside the MSR slot indicating that the magnetic stripe of the card to be read should be facing the display unit. For card reading operation, be sure to insert the card to the bottom of the slot with magnetic stripe of the card near the bottom edge.
  • Page 17 Posiflex Touch Terminal Manager A program named “Posiflex Touch Terminal Manager” and a right- click sticky button tool in the program group “Posiflex Tools” is installed in the preloaded Windows system with a PS/2 interface touch panel controller except in WinCE or Linux environment. This program can also be obtained by download from the POSIFLEX web site.
  • Page 18 Part 18...
  • Page 19 Part 19...
  • Page 20 ĵ§i¨Ï¥ÎªÌ T31454 ³o¬O¥ÒÃþªº¸ê°T²£«~ ¡A ¦b©~¦íªºÀô ¹ Ò ¤ ¤ ¨ Ï ¥ Î ® É ¡A ¥ i ¯ à · | ³ y ¦ ¨ ® g À W ¤ z ÂZ ¡A ¦b³oºØ±¡ªp¤U ¡A ¨Ï¥ÎªÌ·|³Q-n ¨D±Ä¨ú¬Y¨Ç¾A·íªº¹ïµ¦ ¡C ĵ§i Part 20 ¥»¹q¦À¦pªG§ó´«¤£¥¿½T·|¦³Ãz¬µªº¦MÀI ½Ð¨Ì»s³y°Ó»¡©ú®Ñ³B²z¥Î¹L¤§¹q¦À...

This manual is also suitable for:

Dt-208 series

Table of Contents