POSIFLEX PD – 2600 User Manual

POSIFLEX PD – 2600 User Manual

Customer display

Advertisement

PD – 2600 / 2601 / 2602 / 2603 Series
User's Manual
Rev. D0
FCC Notes:
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions manual, may cause interference to radio
communications. It has been tested and found to comply with
limits for a Class A digital device pursuant to subpart J of Part
15 of FCC Rules, which are designed to provide reasonable protection against
interference when operated in a commercial environment. Operation of this equipment
in a residential area is likely to cause interference in which case the user at his own
expense will be required to take whatever measures to correct the interference.
Warranty Limits:
Warranty terminates automatically when any person other than the authorized
technicians opens the machine. The user should consult his/her dealer for the problem
happened. Warranty voids if the user does not follow the instructions in application of
this merchandise. The manufacturer is by no means responsible for any damage or
hazard caused by improper application.
About This Manual:
Posiflex has made every effort for the accuracy of the content in this manual. However,
Posiflex will assume no liability for any technical inaccuracies or editorial or other
errors or omissions contained herein, nor for direct, indirect, incidental, consequential
or otherwise damages, including without limitation loss of data or profits, resulting
from the furnishing, performance, or use of this material.
This information is provided "as is" and Posiflex Technology, Inc. expressly disclaims
any warranties, expressed, implied or statutory, including without limitation implied
warranties of merchantability or fitness for particular purpose, good title and against
infringement.
The information in this manual contains only essential hardware concerns for general
user and is subject to change without notice. Posiflex reserves the right to alter product
designs, layouts or drivers without notification. The system integrator shall provide
applicative notices and arrangement for special options utilizing this product. The user
may find the most up to date information of the hardware from web sites:
http://www.posiflex.com or http://www.posiflex.com.tw
All data should be backed-up prior to the installation of any drive unit or storage
peripheral. Posiflex will not be responsible for any loss of data resulting from the use,
disuse or misuse of this or any other Posiflex product.
All rights are strictly reserved. No part of this documentation may be reproduced,
stored in a retrieval system, or transmitted in any form or by any means, electronic,
mechanical, photocopying, or otherwise, without prior express written consent from
Posiflex Inc. the publisher of this documentation.
© Copyright Posiflex Technology, Inc. 2011
All brand and product names and trademarks are the property of their respective holders.
Part 1
P/N: 19460901150

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PD – 2600 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for POSIFLEX PD – 2600

  • Page 1 About This Manual: Posiflex has made every effort for the accuracy of the content in this manual. However, Posiflex will assume no liability for any technical inaccuracies or editorial or other errors or omissions contained herein, nor for direct, indirect, incidental, consequential or otherwise damages, including without limitation loss of data or profits, resulting from the furnishing, performance, or use of this material.
  • Page 2 Posiflex HT series POS terminals and also the PB series discrete systems. The PD-2602 is a pole mount customer display option designed for Posiflex KS or TP series touch POS terminals. The PD-2603 is a pole mount customer display option designed for Posiflex FT series touch POS terminals.
  • Page 3 INSTALLATION GUIDES HOST SYSTEM PREPARAION For serial interface (RS232) PD-2601or PD-2602 or PD-2603 to be used in HT or PB or KS or TP or FT series, you have to adjust during power off the internal jumper of the host system to supply 5 V DC to the COM port selected for the serial interface pole display.
  • Page 4 “+24 V DC Out” jack in the connector area and insert the other end to the power connector of Posiflex POS printer if needed. Be sure to hear a click at each connection to obtain a firm contact. You may now place the base on a horizontal surface and prepare to power on and adjust the direction of the display head for best viewing effect in application.
  • Page 5 INSTALLING PD-2601 Opening the back cover on system For ease of PD-2601 installation operation, the HT main unit or PB system has to be opened with sufficient precautions. First push in the circled knobs on both sides as in Pix. 1 to remove the back cover.
  • Page 6 Take PD-2601 out of its box and refer to Pix. 3 that is a picture of the pole display base unit (lowest part of the PD) with 2 enlarged portions to the right and a slightly enlarged side view picture to the left to find 2 bottom locking lugs A’;...
  • Page 7 B+B’ B+B’ A’ Pix. 5 Please note the importance of keeping the leftward pressure on bottom end of pole display during the process of turning the pole upright and inserting the locating bosses B’ or even when you want to release the locating bosses B’ away from I/O plate B and turn the upper end of pole display to left to remove the locking lugs A’...
  • Page 8 Fixing pole display base to system To fix the PD-2602 to base of KS or TP systems, please connect the interface cable of PD-2602 through the cable exit in base as in Pix. 9 a peeping view of pole display joint base bottom to the appropriate port in main unit passing Pix.
  • Page 9 With interface cable connection well installed (and with COM port power set for serial models), turn on the HT or KS or TP Posiflex POS system, a firmware identifier as power on sign will appear on the pole display screen for a while to indicate that pole display is self-tested O.K.
  • Page 10 OPOS or JPOS programs and the PD-260X would have to be set to “Epson” command mode. These drivers are available from page: http://www.posiflex.com.tw/Download%20list.asp?Status=1&Series_Name=U POS&Model_Name=OPOS and execute the file “SETUP.EXE” to install the OPOS Control Manager. To add the customer display under OPOS control please set in OPOS Control Manager device name “PD2x-Line Display”...
  • Page 11 WARNING: If the user opens the pole display housing to make any modification, all the product warranty will be voided. NOTE: Please refer to Posiflex Product Information CD or DVD or visit our web http://www/posiflex.com.tw for further information when needed.

This manual is also suitable for:

Pd – 2601Pd – 2602Pd – 2603

Table of Contents