Roland EGX-350 User Manual page 2

For the USA
FEDERAL COMMUNICATIONS COMMISSION
RADIO FREQUENCY INTERFERENCE
STATEMENT
NOTE:
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules.These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment.
This equipment generates, uses, and can radiate radio frequency en-
ergy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to cor-
rect the interference at his own expense.
Unauthorized changes or modification to this system can void
the users authority to operate this equipment.
Use only I/O cables that have been designed and manufactured
specifically for this device.
NOTICE
Grounding Instructions
In the event of a malfunction or breakdown, grounding provides
a path of least resistance for electric current to reduce the risk of
electric shock. This tool is equipped with an electric cord having an
equipment-grounding conductor and a grounding plug. The plug
must be plugged into a matching outlet that is properly installed
and grounded in accordance with all local codes and ordinances.
Do not modify the plug provided - if it will not fit the outlet,
have the proper outlet installed by a qualified electrician.
Improper connection of the equipment-grounding conductor
can result in a risk of electric shock. The conductor with in-
sulation having an outer surface that is green with or without
yellow stripes is the equipment-grounding conductor. If repair
or replacement of the electric cord or plug is necessary, do not
connect the equipment-grounding conductor to a live terminal.
Check with qualified electrician or service personnel if the
grounding instructions are not completely understood, or if in
doubt as to whether the tool is properly grounded.
Use only 3-wire extension cords that have 3-prong grounding
plugs and 3-pole receptacles that accept the tool's plug.
Repair or replace damaged or worn out cord immediately.
For Canada
NOTICE
This Class A digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.
AVIS
Cet appareil numérique de la classe A respecte toutes les
exigences du Règlement sur le matériel brouilleur du Canada.
For California
WARNING
This product contains chemicals known to cause cancer,
birth defects and other reproductive harm.
For EU Countries
Manufacturer:
ROLAND DG CORPORATION
1-6-4 Shinmiyakoda, Kita-ku, Hamamatsu-shi, Shizuoka-ken, 431-2103 JAPAN
The authorized representative in the EU:
Roland DG Corporation, German Office Halskestrasse 7, 47877 Willich, Germany
For EU Countries
WARNING
This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
Operating Instructions
KEEP GUARDS IN PLACE and in working order.
REMOVE ADJUSTING KEYS AND WRENCHES. Form habit
of checking to see that keys and adjusting wrenches are removed
from tool before turning it on.
KEEP WORK AREA CLEAN. Cluttered areas and benches invite
accidents.
DON'T USE IN DANGEROUS ENVIRONMENT. Don't use
power tools in damp or wet locations, or expose them to rain.
Keep work area well lighted.
KEEP CHILDREN AWAY. All visitors should be kept safe dis-
tance from work area.
MAKE WORKSHOP KID PROOF with padlocks, master switch-
es, or by removing starker keys.
DON'T FORCE TOOL. It will do the job better and safer at the
rate for which it was designed.
USE RIGHT TOOL. Don't force tool or attachment to do a job for
which it was not designed.
USE PROPER EXTENSION CORD. Make sure your extension
cord is in good condition. When using an extension cord, be sure
to use one heavy enough to carry the current your product will
draw. An undersized cord will cause a drop in line voltage result-
ing in loss of power and overheating.
WEAR PROPER APPAREL. Do not wear loose clothing,gloves,
neckties, rings, bracelets, or other jewelry which mayget caught in
moving parts. Nonslip footwear is recommended.
Wear protective hair covering to contain long hair.
USE SAFETY GLASSES, face or dust mask if cutting or cleaning
operation is dusty. Everyday eyeglasses only have impact resistant
lenses, they are NOT safety glasses.
SECURE WORK. Use clamps or a vise to hold work when practical.
DON'T OVERREACH. Keep proper footing and balance at all times.
MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean
for best and safest performance. Follow instructions for lubricat-
ing and changing accessories.
DISCONNECT TOOLS before servicing; when changing
accessories,such as blades, bits, cutters, and the like.
REDUCE THE RISK OF UNINTENTIONAL STARTING.
Make sure switch is in off position before plugging in.
USE RECOMMENDED ACCESSORIES. Consult the owner's
manual for recommended accessories. The use of improper
accessories may cause risk of injury to persons.
NEVER STAND ON TOOL. Serious injury could occur if the tool
is tipped or if the cutting tool is unintentionally contacted.
CHECK DAMAGED PARTS. Before further use of the tool, a
guard or other part that is damaged should be carefully checked
to determine that it will operate properly and perform its intended
function - check for alignment of moving parts, binding of mov-
ing parts, breakage of parts, mounting, and any other conditions
that may affect its operation. A guard or other part that is damaged
should be properly repaired or replaced.
NEVER LEAVE TOOL RUNNING UNATTENDED. TURN
POWER OFF. Don't leave tool until it comes to a complete stop.
USE POWER SUPPLY CORD WHICH IS ATTACHED WITH
PRODUCTS. Do not use other power supply cord.