Martin MAC 2000 Profile User Manual
  1. Manuals
  2. Brands
  3. Martin Manuals
  4. Lighting Equipment
  5. MAC 2000 Wash XB
  6. User manual

Martin MAC 2000 Profile User Manual

Hide thumbs Also See for MAC 2000 Profile:
Table of Contents

Advertisement

Quick Links

See also: Service Manual , User Manual
MAC 2000 Profile
user manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MAC 2000 Profile and is the answer not in the manual?

Questions and answers

Related Manuals for Martin MAC 2000 Profile

Summary of Contents for Martin MAC 2000 Profile

  • Page 1 MAC 2000 Profile user manual...
  • Page 2 270° 270° © 2000-2002 Martin Professional A/S, Denmark. All rights reserved. No part of this manual may be reproduced, in any form or by any means, without permission in writing from Martin Professional A/S, Denmark. Printed in Denmark. P/N 35000090 Rev. I...

  • Page 3: Table Of Contents

    MAC 2000 Profile II PCB ........

  • Page 4: Introduction

    If you have questions about how to operate the fixture safely, please contact your Martin dealer or call the Martin 24-hour service hot line at +45 70 200 201.

  • Page 5: Transportation

    RANSPORTATION Important! Release the transport locks before operating the fixture. Included items The MAC 2000 Profile is shipped in a 1 or 2 unit flight case that contains the following items. • User manual • 2 clamp attachment brackets Transport locks The head and yoke may be locked for transportation and service.

  • Page 6: Double Flight Case

    2 Pull the test arms all out. Tilt the fixture up and over the slide arms so that the handle cross-braces that are second from the back rest on the arms. The fixture should rest at an angle. 3 Push the transport drawer into the flight case. MAC 2000 Profile...

  • Page 7: Lamp

    About the HMI 1200 W/S lamp The MAC 2000 Profile comes with a double-ended OSRAM HMI 1200 W/S discharge lamp installed. This highly-efficient short-arc source provides an exceptionally stable 6000K color TO P temperature, a color rendering index greater than 90, and an average life of 750 hours.
  • Page 8 16. Aligning the lamp 1 Switch on the MAC 2000 Profile and allow it to reset. Using either a controller or the control module, turn on the lamp and project an open white beam on a flat surface.

  • Page 9: Ac Power

    MAC 2000 Profile II (magnetic and electronic ballast versions) The MAC 2000 Profile II (identified as such by the label on the side of the product) comes with an auto-sensing, auto-ranging switch-mode power supply. Manual adjustments to the transformer or ballast are not necessary as the MAC 2000 Profile II automatically adapts to the mains voltage and frequency.
  • Page 10 MAC 2000 Profile (magnetic ballast version) In the MAC 2000 Profile with magnetic ballast, both the transformer and the ballast must be tapped correctly for the local AC voltage and frequency. The wrong setting can cause overheating, damage, and poor performance. The factory settings are printed on the serial number label.

  • Page 11: Power Connection

    MAC 2000 Profile (electronic ballast version) In the MAC 2000 Profile with electronic ballast, the transformer must be tapped correctly for the local AC voltage. The electronic ballast automatically adapts to the line voltage and frequency. The wrong transformer setting, though, can cause overheating, damage, and poor performance.

  • Page 12: Data

    Important! Never connect more than 1 data input and 1 data output. The MAC 2000 Profile has both 3-pin and 5-pin XLR sockets for DMX input and output. The pin-out on all sockets is pin 1 to shield, pin 2 to cold (-), and pin 3 to hot (+). There is no connection to pins 4 and 5.

  • Page 13: Rigging

    IGGING The MAC 2000 Profile can be placed on stage or clamped to a truss in any orientation. The Fast-Lock system enables quick and easy fastening of the clamp brackets in 4 positions as shown Figure 11. Figure 11: Clamp bracket positions Warning! Always use 2 clamps to rig the fixture.

  • Page 14: Control Panel

    Navigation The DMX address and any messages (see page 36) are displayed when the MAC 2000 Profile is turned on. To enter the menu, press [Menu]. Press [Up] and [Down] to move within the menu. To select a function or submenu, press [Enter].

  • Page 15: Tailoring Performance

    Tracking Response The MAC 2000 Profile has a filter algorithm that looks at several position updates in tracking control mode and calculates the ideal response for smooth movement. Tracking response is adjustable to compensate for variations in controller performance.

  • Page 16: Readouts

    An on-the-fly position correction system monitors the color wheel, gobo wheels, gobos, rotating effects, and effect wheel. If a position error is detected, the shutter closes while the effect resets. This feature can be disabled by turning U T IL / EF Fb effects feedback ( ) off. MAC 2000 Profile...
  • Page 17 The automatic pan/tilt position correction system may be temporarily turned off under U T I L / F E b A . The off setting, however, is not saved and the system will be re-enabled the next time the fixture starts. If the system cannot correct the pan/tilt position within 10 seconds, feedback is automatically disabled.
  • Page 18 UT IL / CA L/ F OO F Adjust the offset to focus the image. Press [Enter] to save the setting. Software upload The software update mode is normally engaged automatically by the upload device. See Software installation on page 25. MAC 2000 Profile...

  • Page 19: Optical Configuration

    PTICAL CONFIGURATION Gobos Specifications All gobo slots including the seven color/gobo wheel positions accept round theatrical size-E glass gobos. Aluminum gobos are suitable for short-term use only. For best results, custom gobos should meet the following criteria. Outside diameter: ..........37.5 +0/-0.3 mm (1 15/32 +0/-0.01 in.) Maximum image diameter: .

  • Page 20: Replacing Rotating Gobos

    Access gobos from the bottom of the head. Tilt out and remove the holder. coated side The narrow end is on the inside when the spring is pressed flat. Insert spring with narrow end against gobo. Figure 17: Replacing rotating gobos MAC 2000 Profile...

  • Page 21: Effect Wheel

    2 Lock the head in the upside down position and remove the bottom cover. Turn the color/gobo wheel as required to access the desired position. 3 To remove, press the filter or gobo from the lamp side to release it. Remove from wheel. 4 To insert, work the filter or gobo under the retention spring and position it between the pins.

  • Page 22: Effects

    FFECTS The MAC 2000 Profile is compatible with USITT DMX512 controllers. The fixture has two DMX operating modes, 8-bit and 16-bit.16-bit mode requires four more DMX channels than 8-bit mode but provides more precise gobo indexing and pan/tilt positioning. All other functions are identical. The complete DMX protocol begins on page 26.

  • Page 23: Effect Wheel

    Effect wheel The effect wheel provides a variable frost filter and two rotating slots that house a beam shaper and a three-facet prism. The position and velocity of the rotating slots are selected on the effect wheel’s Position / Velocity Channel. The effect wheel channel also provides eight preprogrammed effect combinations.

  • Page 24: Routine Maintenance

    OUTINE MAINTENANCE The MAC 2000 Profile requires routine cleaning. The schedule depends heavily on the operating environment; please consult a Martin service technician for recommendations. Refer all service not described here to a qualified Martin technician. Important! Excessive dust, smoke fluid, and particulate buildup degrades performance and causes overheating and damage to the fixture that is not covered by the warranty.

  • Page 25: Software Installation

    Preventing software updates on a MAC 2000 Profile II Software updates are enabled by default, but on a MAC 2000 Profile II you can disable this by setting the Write jumper (see MAC 2000 Profile II PCB on page 39) to disable.

  • Page 26: Dmx Protocol

    Yellow limit for random CMY color At least 0 ! 100% 0 - 127 0 - 50 At most 0 ! 100% 128 - 255 50 -100 Cold ! Warm (0-178 mireds) 0 - 255 0 - 100 Table 5: DMX protocol MAC 2000 Profile...
  • Page 27 DMX channel Start code = 0 8-bit 16-bit Value Percent Function Color/Gobo Wheel Continuous scroll White ! Position 1 0 - 20 0 - 7 Position 1 ! Position 2 20 - 40 7 - 16 Position 2 ! Position 3 40 - 60 16 - 23 Position 3 ! Position 4...
  • Page 28 CW, fast ! slow 128 - 252 50 - 98 253 - 255 99 - 100 No rotation Gobo Wheel 2, Fine Position Fine Position (LSB), Min ! Max 0 - 255 0 - 100 Table 5: DMX protocol MAC 2000 Profile...
  • Page 29 DMX channel Start code = 0 8-bit 16-bit Value Percent Function Effect Wheel Selection and Macros Effect selection Open Variable frost, 0 ! 100% 1 - 175 1 - 68 176 - 183 69 - 72 Effect 1, indexed rotation Set position / velocity 184 - 191 72 - 75...

  • Page 30: Control Menu

    Return all personality settings (not calibrations) to factory defaults F AC T LO AD Load custom configuration d FS E LO Ad C US 1, C US 2, C US 3 Save current configuration SA VE Table 6: Control menu MAC 2000 Profile...
  • Page 31 V ER Decimal value of the DMX start code. The start code must be 0 for ST CO the MAC 2000 Profile to function properly. d MX L DMX value (from 0 - 255) received for each channel. dI M. . E SP...
  • Page 32 CC WM Gobo wheel 1. Clockwise rotation - slow CW S Gobo wheel 1. Counter clockwise rotation - slow CC WS Clockwise rotation of gobo wheel 1. Slow→fast. I /S 1 0- 25 5 Table 6: Control menu MAC 2000 Profile...
  • Page 33 Menu Item Options Notes (Default settings in bold print) Gobo wheel 2. Open position OP EN Gobo wheel 2. Indexed gobos 1→5 g1 I - g5 I Gobo wheel 2. Rotating gobos 1→5 g1 g - g5 R Gobo wheel 2. Indexed gobo shake 1→5 g1 IS - g5 IS Gobo wheel 2.
  • Page 34 Displayed when lamp hours exceed average life (750 hours) R ep la c e la m p S MS G Displayed if head temperature exceeds 120° C (248° F) F ix tu r e ov e rh e at in g Table 6: Control menu MAC 2000 Profile...

  • Page 35: Adjustment Submenu

    DJUSTMENT SUBMENU UT IL / Ad j This menu is located under Menu Item Options Notes Reset fixture RS T Strike lamp L ON Douse lamp Lo FF Turn dimmer to adjustment position (closed mechanical stop) Ad j Open dimmer OP EN d IM Close dimmer...

  • Page 36: Display Messages

    (Lamp error) and frequency settings match the local reasons are a missing or defective lamp, or supply. insufficient AC voltage. Contact Martin service personnel for ME RR (Memory error) ...the EEPROM memory cannot be read. assistance..the fixture detects the lamp is ON but no ‘Lamp ON’...

  • Page 37: Troubleshooting

    2 and 3 in the fixture that behaves 2 and 3 reversed). erratically. Magnetically indexed effect resets correctly but wanders Disable effects feedback (page 16). Contact Martin Effect wheel requires mechanical adjustment. after fixture reaches operating technician for service. temperature.

  • Page 38: Circuit Board Connections

    IRCUIT BOARD CONNECTIONS MAC 2000 Profile PCB F902 F901 FUSE FUSE 6.3 AT 4.0 AT PL214 PL212 PL905 24V AC RED 24V AC RED 24V AC BLACK 24V AC BLACK BROWN PL904 PL901 12V AC ORA. 12V AC ORA. BLACK 12V AC YEL.

  • Page 39: Mac 2000 Profile Ii Pcb

    MAC 2000 Profile II PCB Circuit board connections...

  • Page 40: Specifications

    Wiring options, MAC 2000 Profile magnetic ballast ....208, 230, 245 V / 50 Hz; 208, 230 V / 60 Hz Wiring options, MAC 2000 Profile electronic ballast ..... . 100, 120, 210, 230, 250 V / 50-60 Hz Main fuses (x 2 - when local AC supply is 200 - 250 V) .
  • Page 41 2 MAC 2000 Profile II Es in a 2-unit flight case ......

Table of Contents