MAC 2000 Wash Service Manual the wires to the junction print. Secure 5 Pull the belt tension pulley forward Zoom motor, replace the bundle under the flexible tie. and loop the new belt over it as shown in Fig. 12.
MAC 2000 Wash Service Manual screw through the first hole in the rail. Zoom lens assembly, replace CMYC module, install Fasten with an M3 nut. 1 Lock the head in the horizontal, top When removing the zoom car, do up position.
MAC 2000 Wash Service Manual 3 Remove the color module attach- 4 Unhook the spring from the motor Color wheel 2 belt, replace ment screws and separate the color bracket. (Fig. 28) wheel module from the zoom module. 5 Transfer the gear (or install a new 1 Remove the color wheel module.
MAC 2000 Wash Service Manual Fasten with 4 M3x6 mm countersunk leads, cut the leads to length, and Head side covers, remove screws. Plug in the wires. install a 2-pole plug. and install 1 Remove the screws that fasten the cover: each cover has two screws.
MAC 2000 Wash Service Manual switch clear of the fan to maintain maxi- 7 Remove the old fan from the heat Heat filter assembly, remove mum airflow. shield and install the new fan. & install 1 Remove the zoom module (p. 3) and CMYC module (p.
MAC 2000 Wash Service Manual 5 Place the top frame over the glass Heat filter, replace Starter, replace and fasten with four screws (4.2x13 self-tap, Torx, black). 1 Remove the heat filter assembly. (p. 1 Remove the zoom module (p. 3), CMYC module (p.
MAC 2000 Wash Service Manual 8 Unscrew, unplug, and remove the 14 Gather white lamp wires Dimmer blades, replace & starter. together with the black and blue starter adjust wires and tie them to the chassis at point 1 in Fig. 51 Tie the wires that lead to the back at point 2.
MAC 2000 Wash Service Manual motors, and the microswitches on the Dimmer motor, replace dimmer half of the module. 1 Remove the dimmer blade as described under “Dimmer blades, replace & adjust” on page 10. 2 Unplug and remove the motor.
MAC 2000 Wash Service Manual 6 If you need to remove the bottom ule with the X filter on top. Skip to step CMYC belts and flags, set of filters (magenta or CTC), first replace remove the idle rail for the top filters.
MAC 2000 Wash Service Manual 15 Clamp the belt in the outside slot 6 Reassemble the fixture. of the slide for the bottom filter. Fig. 76 Cyan motor Fig. 73 Clamp belt in outside slot 16 Verify that the flags slide smoothly in opposite directions and that the bot- tom flag engages the microswitch.
MAC 2000 Wash Service Manual the axle. Remove the old belt and place Tilt belt, right, replace the new one over the large gear. On the right side, the wiring is easiest to disconnect at the yoke. 1 Remove the inside and outside cov- ers from the right arm of the yoke.
MAC 2000 Wash Service Manual inside face of the shaft adaptor. Tighten Tilt motors, synchronize a set screw slightly to fix the position. 7 Fasten the motor bracket to the new 1 Remove the outer arm cover from motor as shown using 3 new M5 x 16 the left or right side of the yoke.
MAC 2000 Wash Service Manual the control panel) and connect it to wires so you can get to the nuts at the Main PCB, replace PL57. Connect the left base fan to bottom of the power supply. PL55. Connect the 4-pin lead from the 5 Remove 2 nuts from the top and 3 control panel to PL33.
MAC 2000 Wash Service Manual mains wire to the neutral terminal (X2) Electronic ballast, replace Base fans, replace on the replacement ballast. 1 Verify that the fixture is discon- 1 Remove the top base covers. nected from AC power. Remove the left or right side cover and handle.
MAC 2000 Wash Service Manual 9 Move the bracket out of the way and Right pan motor, replace Left pan motor, replace remove the motor. 10 Remove the gear from the shaft of 1 Remove the top base covers and The pan lock bridge must be removed in the old motor.
MAC 2000 Wash Service Manual 6 Loosen the hex socket screw that the motor bracket screws so that the 4 Loosen the set screws on either the fastens the power supply mounting motor is securely fastened and does not left or right pan motor gear. The right plate to the chassis.