Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ANTAIRA FCU-1802Px
Summary of Contents for ANTAIRA FCU-1802Px
- Page 1 100Base-FX to 10/100Base-TX Media Converter FCU-1802Px User’s Manual...
- Page 2 Antaira has made every effort to ensure that this User’s Manual is accurate; Antaira disclaims liability for any inaccuracies or omissions that may have occurred.
-
Page 3: Fcc Warning
FCC Warning This equipment has been tested and found to comply with the regulations for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. - Page 4 Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately. Revision User’s manual for Antaira 100Base-FX to 10/100Base-TX PoE Media Converter Rev 1.1 (April 2013) Part No. 2350-AA3540-470...
-
Page 5: Table Of Contents
7. PoE function ..............14 8. LED indication ..............15 9. Cable Connection Parameter ..........16 10. FCU-1802Px Technical Specifications ....... 17 APPENDIX A ............... 18 A.1 Device's RJ-45 Pin Assignments ......... 18 A.2 RJ-45 cable pin assignment ........18... -
Page 6: Overview
Moreover, upon any IEEE 802.3af device installation, the FCU-1802Px or PD can make the connection while migrating the Ethernet digital packets, such as connecting the FCU-1802Px to an IEEE 802.3af complied devices, AP or IP Camera. -
Page 7: Model List
2. Checklist Your FCU-1802Px package should contain the following items: ● 100Base-FX to 10/100Base-TX PoE Media Converter x 1 ● AC-DC Power Adapter (Input: 48V DC, 0.4A max.) x 1 ● User’s Manual x 1 If any items are missing or damaged, please consult the dealer... -
Page 8: Product Outlook
3. Product Outlook Overview Layout of the FCU-1802Px. Rear Panel Bottom TOP Panel Front Panel... - Page 9 Left View There are one RJ-45 Twisted-Pair jack (Auto-MDI/MDI-X), one fiber-optic connector (vary by model) and four LED indicators. LNK/ PoE Media Converter 10/100Base-TX In Use 10/100Base-TX to 100Base-FX Right View One DIP switch for Link Fault Pass Through (LFP) feature, “ON”...
-
Page 10: Link Fault Pass Through (Lfp)
FL/TP ports do not transmit a link signal until they receive a link signal from the opposite port. The diagram below shows a typical network configuration with a good link status using the FCU-1802Px for remote connectivity. Management Switch/Hub... - Page 11 ° LED unlit = no link *Units are shipped with the LFP function disable (OFF). Link Loss Return (LLR) The fiber ports of the FCU-1802Px have been designed with an LLR function for troubleshooting a remote connection. LLR works in conjunction with LLCF.
- Page 12 LFP ON LFP OFF Fiber Cable l LED lit = established link ° LED unlit = no link If one of the optical conductors is bad (as shown in the diagram box below), the converter with LLR function will return a no-link condition to its link partner.
-
Page 13: Installing The Converter
FCU-1802Px will be attached. ● Ensure that there is no activity in the network. ● Attach fiber cable from the FCU-1802Px to the fiber network. TX, RX must be paired at both ends. ● Attach a Cat. 5 UTP cable from the 10/100Base-TX network to the RJ-45 port on the FCU-1802Px. -
Page 14: Poe Function
Before your installation, it is recommended to check your network environment. If there is any IEEE 802.3af devices that need to power on, the FCU-1802Px can provide a way to supply power for this Ethernet device conveniently and easily. The... -
Page 15: Led Indication
7. LED indication • System Color Function Green Lit: Indicate the device is powered. • 10/100Base-TX Port Color Function Indicate that the Media Converter Blink is actively sending or receiving data over that port. LNK/ACT Green Indicate that the port is link up. Indicate that the port is link down. -
Page 16: Cable Connection Parameter
8. Cable Connection Parameter The limitations are as below: Duplex Connection Limitation (max.) Twisted Pair Node to Node Half / Full 100 meters Node to Switch/Hub Multi-Mode Converters Node to Node MM Half 412 meters Node to Switch Node to Node MM Full 2 kilometers Node to Switch... -
Page 17: Fcu-1802Px Technical Specifications
9. FCU-1802Px Technical Specifications The FCU-1802Px comes with the following standard features: ● Standard: IEEE 802.3u, 10/100Base-TX ,100Base-FX IEEE 802.3af Power over Ethernet ● Connectors: • One RJ-45 (Auto-MDI/MDI-X) Twisted Pair, EIA568 with PoE • One Fiber-optic, 1310nm wavelength, connector-type vary with model ●... -
Page 18: Appendix A
APPENDIX A A.1 Device's RJ-45 Pin Assignments • 10/100Mbps, 10/100Base-TX Contact MDI-X 1 (TX +) 2 (TX -) 3 (RX +) 6 (RX -) 4, 5, 7, 8 Not used Not used Implicit implementation of the crossover function within a twisted-pair cable, or at a wiring panel, while not expressly forbidden, is beyond the scope of this standard. -
Page 19: Fiber Optical Cable Connection Parameter
Figure A-1: Straight-Through and Crossover Cable Please make sure your connected cables are with the same pin assignment and color as the above picture before deploying the cables into your network. A.3 Fiber Optical Cable Connection Parameter The wiring details are as below: •... - Page 20 This page is intentionally left blank...
Need help?
Do you have a question about the FCU-1802Px and is the answer not in the manual?
Questions and answers