About The Transverter Output Terminal - Yaesu FTDX9000MP Operation Manual

You may connect an after-market transverter to the rear panel's TRV (Transverter) jack. The output, at 28 MHz, is approxi-
mately –20 dBm (0.01 mW) at 50 Ohms.
Pin 2 (TX GND) of BAND DATA 1Jack or
Pin 2 (TX GND) of BAND DATA 2 Jack
S
ETUP
1. Press the [ MNU ] key to enter the Menu mode (the
LCD will change to Menu display).
2. Rotate the [ MAIN Tuning Dial ] knob to choose Menu
item "TUNING 142 MY BAND".
3. Rotate the [ CLAR/VFO-B ] knob to find the Menu
parameter "TRV OFF" (this is the factory default set-
ting).
4. Press the [ ENT ] key to change the parameter to "TRV
ON" (this will add this condition to your "My Band"
list; see page 56.
5. Press and hold in the [ MNU ] key for at least two sec-
onds to save the new setting and exit to normal opera-
tion.
You may set up the frequency display so that it shows the actual band on which your transverter is operating (instead
of the "IF" used by the transverter, which is the 28 MHz band on your FT
E E E E E
: Setting Up the FT
XAMPLE XAMPLE XAMPLE
XAMPLE XAMPLE
1. Connect the 144 MHz transverter to the transceiver.
2. Use the Menu mode to confirm that Menu item
"GENERAL 041 TRV OFFSET" is set to "44"
(the factory default setting).
3. Press the [ BAND/MHz ] key momentarily, then ro-
tate the [ CLAR/VFO-B ] knob so as to select
"44.000000" on the display.
4. Press and hold in the [ MNU ] key for at least two
seconds to save the new setting and exit.
FT 9000MP O
DX PERATION
A A A A A
BOUT THE BOUT BOUT
BOUT BOUT
TRV Jack
Setting the Transverter Frequency Offset
9000MP Display for Use with a 144 MHz Transverter
DX
M
ANUAL
T T T T T
THE THE THE RANSVER TER RANSVER RANSVER TER TER TER TER
THE RANSVER RANSVER
Coaxial Cable (50 Ohm)
同軸ケーブル（ 50 Ω）
O
PERATION
1. Set up the frequency offset for transverter use, as de-
scribed previously.
2. Rotate the [ MAIN Tuning Dial ] knob to set the de-
sired operating frequency. Operation is basically un-
changed from normal transceiver operation.
A A A A A
When the "TRV" mode is turned on, power output
will not be allowed to pass to the [ANT1] ~ [ANT4]
main antenna jacks. So one of these may be con-
nected to your transverter's "RX" jack. Just be cer-
tain to disconnect the transverter when returning to
HF operation, as the selected Antenna jack will now
be capable of passing RF power.
9000MP).
DX
The "100 MHz" digit of the frequency is not displayed,
so when you are operating on 2 meters and see "45
MHz" on the frequency readout, this indicates "145
MHz" instead.
A A A A A
:
D D D D D VICE VICE VICE VICE VICE
With the setup described above, tuning the operating
range 28-29 MHz will correspond to an actual operat-
ing frequency of 144-145 MHz, with "44-45" being
displayed on the front panel of the transceiver.
O O O O O T T T T T
UTPUT UTPUT UTPUT ERMIN ERMIN AL AL AL AL AL ERMIN
UTPUT UTPUT ERMIN ERMIN
Transceiver V/U ANT
RF IN TX GND
D D D D D VICE VICE VICE VICE VICE
Page 141