Yaesu FTDX9000MP Operation Manual page 36

F F F F F P P P P P C C C C C
R R R R R ONT ONT ONT ONT ANEL ANEL ANEL ONTR ONTR ONTR OLS
ONT ANEL ANEL ONTR ONTR
MCH/GRP Switch
MCH Switch
Pressing this button momentarily allows you to select
the memory channel using the [ CLAR/VFO-B ] knob
(# , described later).
GRP Switch
Pressing and holding in this button for 2 seconds al-
lows you to select the memory group using the [ CLAR/
VFO-B ] knob (#
, described later).
CLAR/VFO-B Knob
Depending on the status of the [ A/B ] switch (#
described later) the [ CLAR/VFO-B ] knob is used for
functions associated with the Main (VFO-A) or Sub
(VFO-B) frequency control registers.
FAST/RX Switch
FAST Switch
When the [ A/B ] switch (#
pushed, and the Umber lamp to the right of the [ CLAR/
VFO-B ] knob (#
, described previously) lights up,
the [ CLAR/VFO-B ] knob will be controlling the Sub
(VFO-B) frequency; pressing the [ FAST/RX ] switch
will change the tuning step of the [ CLAR/VFO-B ]
knob to 100 Hz.
RX Switch
When the [ CLAR ] switch (#
is pressed (and its imbedded LED is illuminated),
pressing the [ FAST/RX ] switch applies the pro-
grammed Clarifier offset to the Main (VFO-A) receive
frequency. Press the [ FAST/RX ] switch once more to
return the Main receiver to the frequency shown on
the main frequency display field; the Clarifier offset
will still be present, though, in case you want to use it
again. To cancel the Clarifier offset, press the
[ B.MODE/CLEAR ] switch (see details in #
low).
Page 34
OLS OLS OLS
OLS
,
, described later) is
, described previously)
be-
VDD BIAS TEMP
BAND/MHz / TX Switch
BAND/MHz
When the [ A/B ] switch (#
pressed, and the Orange lamp to the right of the
[ CLAR/VFO-B ] knob (#
lights up, pressing the [ BAND/MHz ] switch allows
you to rotate this knob for selection of the Amateur
band to be used for the Sub band (VFO-B).
TX Switch
When the [ CLAR ] switch (#
is pressed (and its imbedded LED is illuminated),
pressing the [ BAND/MHz / TX ] switch applies the
programmed Clarifier offset to the Main (VFO-A)
transmit frequency. Press the [ FAST/RX ] switch (#
described previously) once more to return the trans-
mitter to the Main (VFO-A) frequency shown on the
main frequency display field; the Clarifier offset will
still be present, though, in case you want to use it again.
To cancel the Clarifier offset, press the [ B.MODE/
CLEAR ] switch (see details in #
B.MODE/CLEAR Switch
B.MODE Switch
When the [ A/B ] switch (#
the Orange lamp to the right of the [ CLAR/VFO-B ]
knob (# , described previously) lights up, pressing
the [ B.MODE/CLEAR ] switch allows you to rotate
this knob for selection of the operating mode to be
used on the Sub band (VFO-B).
CLEAR Switch
When the [ CLAR ] switch (#
is pressed (and its imbedded LED is illuminated),
pressing the [ B.MODE/CLEAR ] switch clears out any
frequency offset you have programmed into the Clari-
fier register (thereby setting the offset to "Zero").
FT 9000MP O
DX
SWR
, described later) is
, described previously)
, described previously)
,
below).
below) is pressed, and
, described previously)
M
PERATION ANUAL