Summary of Contents for Vicon Roughneck V920D Series
Page 1
24-Hour Technical Support: 800-34-VICON (800-348-4266) UK: 44/(0) 1489-566300 Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your requirements or that the operation will be entirely error free or perform precisely as described in the documentation. This system has not been designed to be used in life-critical situations and must not be used for this purpose.
Page 2
V920D Series of Camera Domes. These units should only be installed by a qualified technician using approved materials in conformance with federal, state, and local codes. Read these instructions thoroughly before beginning an installation. Always refer to Vicon’s website to assure you have the most up-to-date manual, www.vicon-security.com.
Page 3
V920D Series Quick Installation Guide • Package Component The system comes with the following components: Camera unit Installation CD Installation Guide Template Sheet Accessory Kit Optional OSD Controller Check your package to make sure that you received the complete system, including all components shown above.
V920D Series Quick Installation Guide Quick Installation For complete detailed instructions on how to install the V920D, read the Installation section. Installation Diagram...
Note: Failure to thoroughly coat threads will result in moisture entering the housing and eventual failure of the unit. Note: For outdoor installations, Vicon recommends that the vent plug should only be used if fogging conditions exist. Additionally, if the side cable access hole is used, the base must be...
Page 6
V920D Series Quick Installation Guide 2.1 Connection For the operation of the network camera, it is necessary to connect a network cable for data transmission (IP version) and power connection from customer-supplied power adapter. Depending on operation methods, it is possible to additionally connect an alarm cable. Refer to the full User's manual. ...
Page 7
V920D Series Quick Installation Guide External devices can be used to signal the network camera to react on events. Mechanical or electrical switches can be wired to the AI (Alarm In) and G (Ground) connectors. G (Ground): Connect the ground side of the alarm input and/or alarm output to the G (Ground) connector. Alarm Out: The network camera can activate external devices such as buzzers or lights.
V920D Series Quick Installation Guide ▶ ID & IP assignment To make changes in the OSD menu, use the OSD controller (provided optionally). You can set Camera Title and IP Address. 1. Connect the OSD Controller to the Service Monitor port of the network camera. 2.
Page 9
V920D Series Quick Installation Guide If DHCP is enabled and the product cannot be accessed, run the “Smart Manager” utility on the CD to search and allocate an IP address to your products, or reset the product to the factory default settings and then perform the installation again.
V920D Series Quick Installation Guide 3. Operation The network camera can be used with Windows operating system and browsers. The recommended browsers are Internet Explorer®, Safari®, Firefox®, Opera® and Google® Chrome® with Windows. Note: Some screens may appear different (i.e., color scheme) depending on the firmware version, but the functionality is the same or similar.
V920D Series Quick Installation Guide 3.3 Setting the admin password over a secure connection To gain access to the camera, the password for the default administrator user must be set. This is done in the “Admin Password” dialog, which is displayed when the network is accessed camera...
V920D Series Quick Installation Guide The Snapshot button takes a snapshot of the current image. The location where the image is saved can be specified. The Digital Zoom activates a zoom-in or zoom-out function for the video image on the live screen.
V920D Series Quick Installation Guide • Adjusting Zoom: Click“<” button to zoom out and click “>” button to zoom in. The focus is moved slightly after adjusting zoom; adjust the focus again, as necessary. • Adjusting Focus: Click “>” button for far focus and click “<” button to near focus. •...
V920D Series Quick Installation Guide 3.6 Resetting to the factory default settings To reset the network camera to the original factory settings, go to the Setup>System> Maintenance web page (described in “3.5.5 System > Maintenance”) or use the Reset button (SW1) on the board of the dome camera, as described below: •...
Page 15
Vicon Industries Inc. For office locations, visit the website: www.vicon-security.com...
Need help?
Do you have a question about the Roughneck V920D Series and is the answer not in the manual?
Questions and answers