Countertop and freestanding ice and water dispenser with chewblet ice machine (40 pages)
Summary of Contents for Follett Symphony 110 Series
Page 1
110 Series Ice and Water Dispensers Order parts online Installation, Operation and Service Manual www.follettice.com 110CT400A/W-L 110CR400A/W-L 110FB400A/W-L Following installation, please forward this manual to the appropriate operations person. 801 Church Lane • Easton, PA 18040, USA Toll free (800) 523-9361 • (610) 252-7301 Fax (610) 250-0696 •...
Page 2
A return authorization number has been issued by customer service within 30 days after shipment. Follett receives the equipment at the factory in Easton, PA within 30 days after issuance of the return authorization number. The equipment must be returned in Follett packaging. If the packaging has been damaged or discarded, Follett will forward, at the customer’s expense, new packaging.
Table of contents Before you begin Specifi cations Field wiring Installation Installing freestanding dispensers Installing wall mount dispensers Installing Satellite-fi ll ™ icemakers Installing top mount icemakers User information Cleaning and sanitizing procedures Service Information Wiring diagram – lever models Wiring diagram –...
After uncrating and removing all packing material, inspect the equipment for concealed shipping damage. If damage is found, notify your shipper immediately and contact Follett Corporation for help in fi ling a claim, if necessary. Check your paperwork to determine which model you have. Follett model numbers are designed to provide information about the type and capacity of Follett equipment.
Field wiring for countertop and wall mount dispensers with Satellite-fi ll icemakers All fi eld wiring must be installed in accordance with NEC and local electrical codes. Field wiring diagram is intended only to aid electrician or technician in understanding how equipment works. Field wiring for countertop and wall mount dispensers with Satellite-fi ll icemakers Attention –...
Field wiring diagrams Freestanding dispensers and countertop dispensers with integral icemakers IMPORTANT Electric Power Source Standard electrical - 115V, 1 Ph, 60 Hz, FIELD WIRING DIAGRAM IS max. fuse size 20 amps INTENDED TO AID ELECTRICIAN OR TECHNICIAN IN UNDERSTANDING HOW EQUIPMENT WORKS.
Installation procedures Before you begin • All dispensers must be installed level in both directions to ensure proper operation • Required ventilation and recommended service clearances: • Countertop models with Satellite-fi ll icemaker (110CR400A/W) — none. 12" (305mm) at top recommended for service. •...
2. Drill four 3/8" (5mm) holes in counter (Fig. 2) to 24.5" 9" X 14" (227mm x 356mm) anchor dispenser to counter. (622mm) 12.25" (311mm) Follett countertop dispensers can have any or all 23.75" .5" (13mm) (603mm) utilities run directly through counter or out rear of .5" (13mm) 1.625" (41mm) dispenser.
Page 11
10. Apply a thick bead, approximately. 1/4" (6mm) Fig. 4 – Rear connections, countertop models with integral icemakers diameter, of NSF listed silicone sealant (Dow- Corning RTV-732 or equivalent) 1/4" (6mm) inside marked outline of dispenser. (M) 3/8" FPT 11. Carefully position dispenser on counter. icemaker water inlet 12.
Installing Satellite-fi ll icemakers Models110CR400A/W See Icemaker Installation Manual (form #208600) for critical installation instructions for Satellite- fi ll icemakers. Failure to comply with these instructions will result in poor performance and void warranty. 1. Install Satellite-fi ll icemaker following instructions in icemaker manual. 2.
Page 13
2. Remove dispenser top front cover by removing two screws at bottom corners of cover, lifting cover slightly and pulling forward. 3. Remove icemaker compartment top and side panels. 4. Remove icemaker hold-down bracket from front of icemaker compartment. 5. Lift icemaker onto dispenser top and slide icemaker completely into position, compressor end fi rst. Front of icemaker base must be fl ush with front of dispenser.
How the chilled water accessory works Follett’s chilled water accessory uses ice from the dispenser’s storage hopper to chill incoming water supplied to the water station. The water chiller assembly is located in the dispenser cabinet under the storage hopper. As ice is dispensed, it is automatically fed into the water chiller assembly to chill the water coil inside the assembly.
Page 15
Recommended weekly cleaning 1. Wash drain pan and grille with Solution A above. Rinse thoroughly. 2. Slowly pour solution of one cup (8 oz/237ml) household bleach mixed with one gallon (3.8L) hot water into drain pan to help prevent algae growth in drain lines. f dispenser is a SensorSAFE unit: 3.
Service information Wiring diagrams How unit works — lever models The dispense wheel motor and dispense solenoid are energized through the power and ice dispense switches. The water solenoid valve is energized through the power and water dispense switches. The icemaker receives the bin signal through the power switch, the normally closed bin thermostat and the icemaker switch.
How unit works — SensorSAFE models SensorSAFE models provide “touchless” ice and water dispensing. When a container is placed within the actuation zone below the ice or water chute on SensorSAFE dispenser models, an infrared signal refl ects off the container and is detected by the sensor.
Dispenser troubleshooting Disconnect power to dispenser and icemaker before putting hands or arms in storage area, or attempting any repair or service to equipment. Before calling for service: • Check that there is ice in dispenser bin area • Check that all switches and circuit breakers are on •...
Troubleshooting SensorSAFE board and sensors Board guide LEDs, when illuminated, indicate the following: Terminals: (board power) (incoming power, hot) (cleaning, no dispensing cycle) (neutral terminals) (ice dispensing activated) (power terminal for water solenoid) (water dispensing activated) (power terminal for dispense gate solenoid) not used (power terminal for wheel motor) (terminals for clean cycle switch)
Ice transport tube replacement Model 110CT400A/W Only use tubing supplied by Follett Corporation. TIGHTEN CLAMP SCREW Ice transport tube replacement Models 110FB400A/W, 110CR400A/W Correct installation of ice transport tube is critical to Satellite-fi ll icemaker performance. Replacement ice transport tubes for Satellite-fi ll icemakers must be insulated and run continuously from icemaker to dispenser with no dips or bends with a radius of less than 6"...
Page 22
9. Slip supplied hose clamp onto tube and push tube onto exit port of evaporator. Do not twist hose when securing to evaporator. Only use tubing supplied by Follett Corporation. 10. Fasten tube on port with hose clamp, being sure that clamp is positioned on evaporator side of nozzle fl ange.
Thermostat locations Thermostat locations – 110CT400A/W ice deflector bracket assembly rubber grommet ice level control stat ice level control stat bin thermostat control box assembly hopper assembly control box assembly .75" ice level (20mm) control stat Hand bend cap tube end to approx.
Electrical box (front view) – SensorSAFE models Part # Description Reference 500514 Thermostat, bin level 502209 Switch, dispenser power 502209 Switch, icemaker bin signal 502242 Control board, SensorSAFE 502359 Clean switch, SensorSAFE Not shown 501841 Boot, clean switch Not shown Wheel motor and drive system Part # Description...
Hopper components Top view – top mounted unit Top view – freestanding and Satellite-fi ll units Ice tube bracket – side view – Ice tube bracket – side view freestanding & Satellite-fi ll units – all top mounted units Dispense wheel – bottom view all units Part # Description Reference...
Ice transport tubing Part # Description Reference 502522 Ice transport tube (Satellite-fi ll units) – 10 ft (3.1m) Not shown 502523 Ice transport tube (Satellite-fi ll units) – 20 ft (6.1m) Not shown 501176 Ice transport tube insulation (Satellite-fi ll units only) – sold by the foot Not shown 502327 Ice transport tube assembly (110 freestanding units)
Page 32
Satellite-fi ll, SensorSAFE and Symphony are trademarks of Follett Corporation. 801 Church Lane • Easton, PA 18040, USA 208597R06 Toll free (800) 523-9361 • (610) 252-7301 09/09 Fax (610) 250-0696 • www.follettice.com...