Range Technical Data; Quick Reference Sheet; Maximum Allowable Surface Temperatures; Rtd Temperature / Resistance Chart - Electrolux 30” GAS FREESTANDING RANGES Service Update Manual

Maximum Allowable Surface Temperatures

All gas and electric ranges must comply with U.L and A.N.S.I. surface temperature limits outlined in the following chart.
Note that the testing temperature is different for electric ranges produced after 08/26/2003.
SURFACE TEMPERATURE LIMITS
1. Product must be undamaged, correctly assembled and have the cor-
rect oven temperature.
2. All skin temperatures are based on a room temperature of 77° F (25°
C) and an oven set temperature of 400° F for gas and electric ranges
built prior to 08/26/2003. Oven set temperature should be 475° F for
electric products built after 8/26/2003.
3. Oven must be cycling at designated test temperature for one hour
before test is conducted.
4. Pyrometers, (temperature testers), must be of high quality and prop-
erly adjusted.
5. An increase or decrease of 1° F in the room ambient temperature, will
allow a 1° F increase or decrease in the maximum allowable surface
temperature of the range.

RTD Temperature / Resistance Chart

The following chart can be used to test the resistance of the oven temperature
sensor probe. For accuracy in testing use a high quality thermometer or
temperature meter to determine actual oven temperature before reading the
resistance of the probe.
To Remove Warmer Drawer:
1. Turn power off before removing the Warmer
Drawer.
2. Open the drawer to the fully opened position.
3. Locate glide lever on each side of drawer, pull
up on the left glide lever and push down on the
right glide lever (see Figure 1).
4. Pull the drawer away from the range.
Fig. 2

RANGE TECHNICAL DATA

Quick Reference Sheet

Side Panel
Oven Door
Warmer Drawer
Front Panel
Knobs & Handles
Skirt
Cooktop
Lower Console
Oven Vent Area
* Includes plastic with metal plating not more than 0.005" thick and metal with a plastic covering not
less than 0.005" thick.
** Self-Clean Electric Range at Clean Temperature

Removing and Replacing Warmer Drawer

Fig. 1
Page
MATERIAL TYPE / FINISH
PAINTED PORCELAIN
LOCATION
152° F 160° F
152° F 160° F
152° F 160° F
— —
— —
NO TEMPERATURE LIMITS APPLY TO THIS AREA
TEMPERATURE °F
Electrical Shock Hazard can occur
and result in serious injury or death.
Disconnect appliance from electric
power before cleaning and servicing
the warmer drawer.
To Replace Warmer Drawer:
1. Pull the bearing glides to the front of the
chassis glide (see Fig. 2).
2. Align the glide on each side of the drawer with
the glide slots on the range.
3. Push the drawer into the range until levers
"click" (approximately 2").
open again to seat bearing glides into position.
If you do not hear the levers "click" or
the bearing glides do not feel seated
remove the drawer and repeat steps 1
thru 3. This will minimize possible damage to
the bearing glides.
7
GLASS PLASTIC METAL
— —
172° F 182° F
— —
— *167° F 131° F
**182° F **152° F
— *182° F *152° F
RTD SCALE
RESISTANCE Ω
32 ± 1.9 1000 ± 4.0
75 ± 2.5 1091 ± 5.3
250 ± 4.4 1453 ± 8.9
350 ± 5.4 1654 ± 10.8
450 ± 6.9 1852 ± 13.5
550 ± 8.2 2047 ± 15.8
650 ± 13.6 2237 ± 18.5
900 ± 13.6 2697 ± 24.4
Pull the drawer
P/N 316439221
—
—
—