Advertisement
Quick Links
HigH-Output B
2130
ASSEMBLY and OPERATING INSTRUCTIONS
Congratulations on the purchase of this new EarthWay spreader. Please call us if you have any difficulty with assembly or
operation of this spreader. We can be reached via the telephone at 800-294-0671 or 574-848-7491 Monday—Friday 9:00am
~ 4:00pm or visit us online at www.earthway.com This spreader comes with lifetime technical support, email: techsupport@
earthway.com
HELPFUL HINTS: READ THE DIRECTIONS BEFORE ASSEMBLY
THIS SPREADER COMES PARTIALLY ASSEMBLED, REQUIRING YOU TO INSTALL THE WHEELS, HANDLE ASSEMBLY
AND CONTROL ROD. IT SHOULD TAKE APPROXIMATELY 10 MINUTES WITH THE USE OF TWO 7/16" WRENCHES AND 1
PAIR OF PLIERS.
Clean the impeller plate after each use. Material stuck on the impeller blades will cause uneven spreading.
9
Your spreader is designed to be pushed at three miles per hour, which is a brisk walking speed. Slower or faster speeds
9
will change the spread patterns. Wet material will also change the spread pattern and flow rate.
Clean your spreader thoroughly after each use. Wash between the shut off plate and bottom of the hopper.
9
Gears are permanently lubricated at the factory. Do not open the gearbox or dirt may enter.
9
When using Rock Salt remove the agitator to prevent damage to the gearbox and remove salt from the hopper daily. Rock
9
Salt will reconstitute back into a solid block over night with humidity.
Open carton and remove the handle assembly, wheels,
1
.
and spreader from carton.
2. Turn spreader upside-down on to the hopper.
3. Ensure that the axle bearings are pushed into the axle
bushing on both sides as shown. Install drive wheel (both
wheels are interchangeable) to axle using pin hole nearest to
lower handles as shown. Insert 2" cotter pin through wheel and
through axle. Bend with pliers to prevent pin from falling out.
4. Install coast wheel to axle, then using outside pin hole as shown,
insert 1" cotter pin through axle (not thru the wheel). Bend with pliers to
prevent pin from falling out.
s
roadcast
preader
Lower Handle
Frame Brace
Coast Wheel
1" Cotter Pin
EarthWay
EarthWay
EarthWay
EarthWay
Gearbox
Axle Assembly
Cross Brace
2" Cotter Pin
Drive Wheel
Pt# 53107
®
®
PAGE 1
Advertisement
Related Manuals for EarthWay 2130 High-Output
Summary of Contents for EarthWay 2130 High-Output
- Page 1 ASSEMBLY and OPERATING INSTRUCTIONS Congratulations on the purchase of this new EarthWay spreader. Please call us if you have any difficulty with assembly or operation of this spreader. We can be reached via the telephone at 800-294-0671 or 574-848-7491 Monday—Friday 9:00am ~ 4:00pm or visit us online at www.earthway.com This spreader comes with lifetime technical support, email: techsupport@...
- Page 2 5. Install handle shaft to lower handles and pivot & bracket assembly as shown. Using 2” bolts and locknuts. TIGHTEN BOLTS AND NUTS NOW. 1/4 - 20 Lock-nut Pivot Bracket 1/4 - 20 x 1-3/4” Bolt Upper Handles 6. (This step is only required if you want to change the position of the handles) NOTE: Upper handles have 3-positions that you can Handle 1/4-20...
- Page 3 5-Years to the end user with the original purchase receipt. If a manufacturing non-conformance is found, EarthWay Products, Inc. at its discretion will repair or replace the part(s) or product at no charge provided the failure is not the result of incorrect installation, mishandling, misuse, tampering, or normal wear and tear as determined by EarthWay .
- Page 4 EarthWay Products, Inc. P.O. Box 547 Bristol, IN 46507 Phone: 800-294-0671 www.earthway.com 2130 HigH-Output Broadcast Spreader ~ Parts List Key # Part # Description Key # Part # Description 60250 Hopper Assembly, Includes Key #4, #5 & 18 12354 Shut-Off Plate...