Advertisement
Quick Links
2130
HIGH-OUTPUT B
ASSEMBLY and OPERATING INSTRUCTIONS
PLEASE CALL IF YOU ARE MISSING ANY PARTS, HAVE ANY DIFFICULTY IN ASSEMBLY, OR HAVE ANY QUESTIONS
REGARDING THE SAFE OPERATION OF THIS SPREADER. THIS MODEL INCLUDES LIFETIME TECHNICAL SUPPORT
SUPPORT HOT LINE: 574-848-7491 or 800-294-0671,
HELPFUL HINTS: READ THE DIRECTIONS BEFORE ASSEMBLY
THIS SPREADER COMES PARTIALLY ASSEMBLED, REQUIRING YOU TO INSTALL THE WHEELS, HANDLE ASSEMBLY AND
CONTROL ROD. IT SHOULD TAKE APPROXIMATELY 10 MINUTES WITH THE USE OF TWO 7/16" WRENCHES AND 1 PAIR
OF PLIERS.
; Clean the impeller plate after each use. Material stuck on the impeller blades will cause uneven spreading.
; Your spreader is designed to be pushed at three miles per hour, which is a brisk walking speed. Slower or faster speeds
will change the spread patterns. Wet material will also change the spread pattern and flow rate.
; Clean your spreader thoroughly after each use. Wash between the shut off plate and bottom of the hopper.
; Gears are permanently lubricated at the factory. Do not open the gearbox or dirt may enter.
; When using Rock Salt remove salt from the hopper daily. Rock Salt will reconstitute back into a solid block over night
with humidity. As a preventative measure, spray all metal parts thoroughly (inside the tubing too) with WD-40 to prevent
corrosion.
1. Open carton and remove the handle assembly, wheels, and
spreader from carton.
2. Turn spreader upside-down on to the hopper.
3. Ensure that the axle bearings are pushed into the axle bushing
on both sides as shown. Install drive wheel (both wheels are
interchangeable) to axle using pin hole nearest to lower handles as
shown. Insert 2" cotter pin through wheel and through axle. Bend
with pliers to prevent pin from falling out.
4. Install coast wheel to axle, then using outside pin hole as shown, insert 1" cotter pin
through axle (not thru the wheel). Bend with pliers to prevent pin from falling out.
s
roadcast
preader
:
@
email
techsupport
earthway
Lower
Handle
Frame
Brace
Coast Wheel
1" Cotter Pin
EarthWay
EarthWay
EarthWay
EarthWay
Rev. 3-10
.
SKYPE: EARTHWAY.TECH
com
Gearbox
Axle Assembly
Cross Brace
2" Cotter Pin
Pt# 53107
®
®
Drive Wheel
PAGE 1
Advertisement
Related Manuals for EarthWay 2130
Summary of Contents for EarthWay 2130
- Page 1 2130 EarthWay EarthWay EarthWay EarthWay HIGH-OUTPUT B ® ® roadcast preader ASSEMBLY and OPERATING INSTRUCTIONS Rev. 3-10 PLEASE CALL IF YOU ARE MISSING ANY PARTS, HAVE ANY DIFFICULTY IN ASSEMBLY, OR HAVE ANY QUESTIONS REGARDING THE SAFE OPERATION OF THIS SPREADER. THIS MODEL INCLUDES LIFETIME TECHNICAL SUPPORT SUPPORT HOT LINE: 574-848-7491 or 800-294-0671, SKYPE: EARTHWAY.TECH...
- Page 2 5. Install handle shaft to lower handles and pivot & bracket assembly as shown. Using 2” bolts and locknuts. TIGHTEN BOLTS AND NUTS NOW. 1/4 - 20 Lock-nut Pivot Bracket 1/4 - 20 x 2” Bolt Upper Handles 6. (This step is only required if you want to change the position of the handles) NOTE: BEFORE INSTALLING GAUGE AND UPPER HANDLES TO HANDLE SHAFT, UPPER HANDLES FEATURE Handle...
- Page 3 5-Years to the end user with the original purchase receipt. If a manufacturing non-conformance is found, EarthWay Products, Inc. at its discretion will repair or replace the part(s) or product at no charge provided the failure is not the result of incorrect installation, mishandling, misuse, tampering, or normal wear and tear as determined by EarthWay .
- Page 4 Bristol, IN 46507 Phone: 800-294-0671 www.earthway.com 77003 OPTIONAL Heavy-Duty Rain Cover 60184 OPTIONAL Salt Deflector Kit 2130 HIGH-OUTPUT Broadcast Spreader ~ Parts List KEY # PART # DESCRIPTION KEY # PART # DESCRIPTION 60250 HOPPER ASSEMBLY 12354 ICE MELT SHUT-OFF...