Download
Share
Print this page
EarthWay 2150 Assembly And Operating Instructions Manual
  1. Manuals
  2. Brands
  3. EarthWay Manuals
  4. Spreader
  5. EV-N-SPRED 2150
  6. Assembly and operating instructions manual

EarthWay 2150 Assembly And Operating Instructions Manual

Commercial broadcast spreader with ssc
Hide thumbs Also See for 2150:
1
2
3
4
5
6
7
8

Advertisement

Quick Links

Download this manual
2150 Commercial
Broadcast Spreader
ASSEMBLY and OPERATING INSTRUCTIONS
PLEASE CALL IF YOU ARE MISSING ANY PARTS, HAVE ANY DIFFICULTY IN ASSEMBLY, OR HAVE ANY QUESTIONS
REGARDING THE SAFE OPERATION OF THIS SPREADER. THIS MODEL INCLUDES LIFETIME TECHNICAL SUPPORT
SUPPORT HOT LINE: 574-848-7491 or 800-294-0671, email: techsupport@earthway.com
HELPFUL HINTS:
; If your spreader does not spread evenly, be sure "FRONT" on the GEARBOX points to the front of the spreader.
The impeller must turn clockwise when pushing forward. Reversing the GEARBOX will cause the impeller
to turn counter clockwise. Clean the impeller plate after each use. Fertilizer stuck on the impeller blades will
cause uneven spreading.
; Your spreader is designed to be pushed at three miles per hour, which is a brisk walking speed. Slower or
faster speeds will change the spread patterns. Wet fertilizer will also change the spread pattern and flow rate.
Clean and dry your spreader thoroughly after each use. Coat all metal surfaces (inside & outside of tubing)
with light oil, Fluid Film
of the hopper. Do not use powdered materials as it will damage the gearbox.
; Gears are permanently lubricated at the factory. Do not open the GEARBOX or dirt may enter.
IF YOUR SPREADER COMES SEMI ASSEMBLED, SKIP TO STEP #7
32100
Qty 2
33117
Qty 1
12152
31104
Qty 2
31100
Qty 4
Qty 4
12148
Qty 2
1. Remove and identify all loose parts from carton
(Qty 4) #31104
#14 X 1-1/2"
Flat Head Screw
READ THE DIRECTIONS BEFORE ASSEMBLY
or silicon spray to help prevent corrosion. Wash between the shut off plate and bottom
®
32103
Qty 8
33108
Qty 1
33109
31120
Qty 1
Qty 4
31106
Qty 2
.
2. Position hopper as shown at the left. Install FRAME using (4) #14 x 1½" Flat
Head Phillips screws. TIGHTEN THESE NOW
with SSC
ROCK SALT and POWDERED
MATERIALS should not be used in
this spreader as it will damage the
GEARBOX and can void the warranty.
Use only granular materials.
13
17
16
31
24
23
9
29
25
26
38
11-21-2017 Pt# 52157
12
11
28
PAGE 1

Advertisement

loading

Related Manuals for EarthWay 2150

Summary of Contents for EarthWay 2150

  • Page 1 PLEASE CALL IF YOU ARE MISSING ANY PARTS, HAVE ANY DIFFICULTY IN ASSEMBLY, OR HAVE ANY QUESTIONS REGARDING THE SAFE OPERATION OF THIS SPREADER. THIS MODEL INCLUDES LIFETIME TECHNICAL SUPPORT SUPPORT HOT LINE: 574-848-7491 or 800-294-0671, email: techsupport@earthway.com HELPFUL HINTS: READ THE DIRECTIONS BEFORE ASSEMBLY ;...
  • Page 2 4. Install GEARBOX by inserting the PINION SHAFT into hole in center of HOPPER bottom. The word “FRONT” on the GEARBOX must point to Front of the HOPPER. The EarthWay logo is on the front of the hopper. 5. STEP A - Install LOWER HANDLES onto FRAME to both sides as Gearbox Assembly shown.
  • Page 3 NOW GO BACK AND TIGHTEN ALL NUTS AND BOLTS STARTING WITH FIRST STEP. DO NOT OVER TIGHTEN. 7. Install DRIVE WHEEL onto the AXLE and align with the cotter pin hole nearest to LOWER HANDLE as shown. Insert 2” cotter pin through wheel and through AXLE. Bend with pliers to prevent pin from falling out. 8.
  • Page 4 13. Install HANDLE SHAFT to LOWER HANDLEs and PIVOT & BRACKET assembly as shown. Using 2” bolts and locknuts. TIGHTEN BOLTS AND NUTS NOW. 1/4 - 20 Lock-nut Pivot Bracket 14. Install (1) 1/4-20 1/4 - 20 x 2” Bolt regular nut (not a locknut) on to CONTROL ROD as shown.

  • Page 5: Year Limited Warranty

    5-YEAR LIMITED WARRANTY Earthway Products, Inc. warrants this product free of defects in original workmanship and materials for a period of 5-years to the end user with the original purchase receipt. If a manufacturing non-conformance is found, Earthway Products, Inc.
  • Page 6 #14 X 1 1/2 TYPE 25 FHPS ZINC 44249 FRAME BRACE (2150/2170) 32103 1/4-20 NYLON INS LOCKNUT ZINC 25228 CROSS BRACE (2150/2170/S25) 11.25 REV908 11927 SHUTOFF SUPPORT- LARGE 31106 1/4-20 X 2 1/4" HHCS ZINC 31120 1/4-20 X 2" HHCS ZINC 12110 IMPELLER 9"...
  • Page 8 FLOWER Does not change the setting rate © 2017 Earthway Products, Inc. All rights reserved The settings furnished on the Rate Setting Matrix are intended as a guide only. Variations in physical characteristics of material applied, walking speed, and roughness of ground surface may require slightly different spreader settings. Due to the...