EarthWay EV-N-SPRED 2170 Assembly And Operating Instructions Manual
  1. Manuals
  2. Brands
  3. EarthWay Manuals
  4. Spreader
  5. 2170
  6. Assembly and operating instructions manual

EarthWay EV-N-SPRED 2170 Assembly And Operating Instructions Manual

Commercial broadcast spreader
Hide thumbs Also See for EV-N-SPRED 2170:
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

2170 C
ommerCial
B
roadcast
ASSEMBLY and OPERATING INSTRUCTIONS
PLEASE CONTACT US IF YOU ARE MISSING ANY PARTS, HAVE ANY DIFFICULTY IN ASSEMBLY, OR HAVE ANY
QUESTIONS REGARDING THE SAFE OPERATION OF THIS SPREADER. THIS MODEL INCLUDES LIFETIME
TECHNICAL SUPPORT. HOT LINE: 574-848-7491 OR 800-294-0671, EMAIL: TECHSUPPORT@EARTHWAY.COM
HELPFUL HINTS:
; If your spreader does not spread evenly, be sure the FRONT on the gear box points to the front of the spreader.
The impeller must turn clockwise. Reversing the gearbox will cause the impeller to turn counter clockwise.
Clean the impeller plate after each use. Fertilizer stuck on the impeller blades will cause uneven spreading.
; Your spreader is designed to be pushed at three miles per hour, which is a brisk walking speed. Slower or
faster speeds will change the spread patterns. Wet fertilizer will also change the spread pattern and flow rate.
Clean and dry your spreader thoroughly after each use. Coat all metal surfaces (inside & outside of tubing)
with light oil or silicon spray to help prevent corrosion. Wash between the shut off plate and bottom of the
hopper. Do not use powdered materials.
; Gears are permanently lubricated at the factory. Do not open the gearbox or dirt may enter.
IF YOUR SPREADER COMES SEMI ASSEMBLED, SKIP TO STEP #7
32100
33117
Qty 2
Qty 1
36210
Qty 2
36214
31100
Qty 4
Qty 4
12152
12148
Qty 2
Qty 2
1. Remove and identify all loose parts from carton
(Qty 4 #36214)
1/4-20 X 1½"
Phillips Panhead
s
preader
READ THE DIRECTIONS BEFORE ASSEMBLY
36300
32103
Qty 6
Qty 9
33108
36105
Qty 1
Qty 1
33109
Qty 1
31120
Qty 5
31106
Qty 2
.
(Qty 4 #36300)
1/4-20 SS Locknut
ROCK SALT and POWDERED MATERIALS
should not be used in this spreader as
it will damage gearbox and can void
Use only granular materials.
13
16
31
2. Position hopper on side. Install frame using (4) 1/4-20 x 1-1/2"
Pan Head Phillips bolts and (4) 1/4-20 nylon insert locknuts. First put
bolts through holes in frame then through holes in bottom of hopper.
Secure with locknuts. TIGHTEN THESE LOCKNUTS NOW - DO NOT
TIGHTEN WITH POWER TOOLS. TIP: coat stainless steel bolts
with wax or grease before tightening to prevent them from seizing.
warranty.
24
23
17
9
40
25
26
38
8-2014 Pt# 52164
12
11
28
PAGE 1

Advertisement

Table of Contents
loading

Related Manuals for EarthWay EV-N-SPRED 2170

Summary of Contents for EarthWay EV-N-SPRED 2170

  • Page 1 PLEASE CONTACT US IF YOU ARE MISSING ANY PARTS, HAVE ANY DIFFICULTY IN ASSEMBLY, OR HAVE ANY QUESTIONS REGARDING THE SAFE OPERATION OF THIS SPREADER. THIS MODEL INCLUDES LIFETIME TECHNICAL SUPPORT. HOT LINE: 574-848-7491 OR 800-294-0671, EMAIL: TECHSUPPORT@EARTHWAY.COM HELPFUL HINTS: READ THE DIRECTIONS BEFORE ASSEMBLY ;...

  • Page 2: Gearbox Assembly

    Pinion GEARBOX ASSEMBLY Shaft 1/8 x 1-1/4” Impeller Cotter Pin (#36105) Cross Brace Gearbox Brace 3. Install impeller onto pinion shaft. Insert 1/8”x 1¼” cotter pin through impeller then through pinion shaft. Use hole closest to the gear box. Spread cotter pin to prevent from 4.
  • Page 3 Drive wheel side 2” Cotter Pin Bushing Install the axle as shown above Coast wheel side 1” Cotter Pin Bushing 7. Slide axle into the lower handle, then the gearbox and into axle bearing on the other lower handle as shown above. Finally slide the bushings over the axle as shown above.
  • Page 4 13. Install handle shaft to lower handles and pivot & bracket assembly as shown. Using 1/4 -20 x 2” bolts and locknuts. TIGHTEN BOLTS AND NUTS NOW. 1/4 - 20 Lock-nut Pivot Bracket 1/4 - 20 x 2” Bolt 14. Install (1) 1/4-20 Hex nut (not a locknut) on to control rod as Long End...

  • Page 5: Year Limited Warranty

    Products, Inc. To seek remedy under this warranty, contact Earthway Products, Inc. at 574-848-7491, techsupport@earthway. com or write to Earthway Products, Inc. P.O. Box 547 Bristol, Indiana 46507 and describe the nature of the manufacturing defect. SPECIFIC LIMITATIONS: This warranty covers only the part(s) or product; any labor charges associated with repair or replacement of non-conformances are specifically excluded.

  • Page 6: Parts List

    Earthway Products, Inc. P.O. Box 547 Bristol, IN 46507 Phone: 800-294-0671 www.earthway.com 77002 OPTIONAL Heavy-Duty Rain Cover 60060R OPTIONAL Heavy-Duty Rain Cover 1” & Side Deflector Kit 1-1/2” 2” 2-1/4” 2-3/4” 60166R OPTIONAL 3-Side Salt Deflector Kit Standard Settings (12196) Gauge Overlay and OPTIONAL Lesco Settings (12195) Gauge Overlay You can find replacement nuts &...

Table of Contents