FAAC S450H Instructions For Intallation
  1. Manuals
  2. Brands
  3. FAAC Manuals
  4. Gate Opener
  5. S450H
  6. Instructions for intallation
FAAC S450H Instructions For Intallation

FAAC S450H Instructions For Intallation

24v hydraulic swing gate operator
Hide thumbs Also See for S450H:
Table of Contents

Advertisement

Quick Links

See also: Owner's Manual , Manual
S450H
24V Hydraulic Swing Gate Operator
UL325 - UL991
FAAC International Inc.
FAAC International Inc.
Headquarter & East Coast Operations
West Coast Operations
5151 Sunbeam Road
357 South Acacia Avenue
Suites 9-11
Unit 357
Jacksonville, FL 32257
Fullerton, CA 92831
Tel. (866) 925-3222
Tel. (800) 221-8278
www.faacusa.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the S450H and is the answer not in the manual?

Questions and answers

Related Manuals for FAAC S450H

Summary of Contents for FAAC S450H

  • Page 1 S450H 24V Hydraulic Swing Gate Operator UL325 - UL991 FAAC International Inc. FAAC International Inc. Headquarter & East Coast Operations West Coast Operations 5151 Sunbeam Road 357 South Acacia Avenue Suites 9-11 Unit 357 Jacksonville, FL 32257 Fullerton, CA 92831 Tel.

  • Page 2: Table Of Contents

    Read this instruction manual before you begin installing the product. = Information regarding personal safety and proper maintanence of the product. FAAC Model S450H - Rev: 02 - NOV 2011 FA A C M o d el S 4 50H 24V Hydraulic Swing Gate Operator...

  • Page 3: Important Safety Information

    • Use only FAAC “Photobeam” photoelectric eyes to comply with UL325. FA A C M o d e l S 45 0H 24V Hydraulic Swing Gate Operator...

  • Page 4: General Safety Precautions

    • Install devices such as reversing edges and photo • Use only FAAC MSE MO, CN60 or M60 edge beams to provide better protection for personal sensors. property and pedestrians. Install reversing devices that are appropriate to the gate design and application.

  • Page 5: Ul325 Gate Operator Classifications

    Installing the Warning Signs This FAAC swing gate operator is supplied with two warning signs to alert people that a possible hazard exists and that appropriate actions should be taken to avoid the hazard or to reduce exposure to it.

  • Page 6: Description And Technical Specifications

    DIMENSIONS 1. DESCRIPTION AND TECHNICAL SPECIFICATIONS The FAAC S450H automated system for swing-leaf gates con- sists of an electrical pump and an hydraulic piston transmitting the leaf movement, assembled in a single block. The model with hydraulic locking can automate leaves up to 4¾...

  • Page 7: Installation Dimensions

    - - If the gate structure does not allow the stable fixing of the front fitting, create a firm bearing surface in the leaf structure. - It is advisable to grease all fixing pins - Opening and closing stops must always be installed - Pay special attention not to damage the operator rod.
  • Page 8 3.1.2 APPLICATION WITH BRACKET FASTENED TO SIDE WALL ATTENTION: do not cut the rear bracket for any reason. Refer to Figures 4 1 and 5 1 and Table 2 to determine the installation position of the operator. 3⅜ Dimensions in Inches Fig.5 1 Fig.4 1 Dimensions in Inches...

  • Page 9: Installing The Operator

    INSTALLING THE OPERATOR Install the encoder on the rear bracket by correctly engaging it on the pin, then fix it with the screw and nut Check the perfect level then weld the rear fitting to the pil- supplied (Fig. 8 Ref. a, b and c). lar or fix it by means of suitable screws, dowels / thread- ed inserts.
  • Page 10 15. Secure the operator to the front bracket (Fig. 15). 16. Remove the bleed screw (Fig.16 Ref. a) paying special attention to leave the sealing O-Ring in its seat. If an external mechanical 17. Install the metallic protection cover as shown in Fig. 16, stop point at closure is insert and tighten both tie-rods.

  • Page 11: Manual Operation

    MANUAL OPERATION Models S450H and SB are not equipped with a release facility because, thanks to the particular configuration of the hydraulic distributing flange, you do not need to release the operator to manually move the leaf. If the gate is to be operated manually because of a power failure or an automated system fault, activate the release device.
  • Page 12 Fig. 19 LEAF 1* LEAF 2 DL 1 DL 1 THROUGH THE BRACKET COVER OF LEAF THROUGH THE BRACKET COVER OF LEAF DL 2 DL 2 2, VERIFY THAT THE LED DL1 IS ON WHEN 1, VERIFY THAT THE LEDS DL1 AND DL2 DL 3 DL 3 THE MOTOR IS NOT IN OPERATION...

  • Page 13: Bleeding

    BLEEDING Loosen the tie-rods (Fig. 23 ref. a) and remove the metal protective housing (Fig. 23 ref. b). Remove the upper tie-rod and be careful with the O-ring that must remain it its seat. Fig.23 Remove the screw in Fig. 24 ref.d from the front fitting Remove the joint (Fig.24 ref.f) from the operator stem.

  • Page 14: S450H Parts Diagrams

    Diagram 1 Part Part Description Part Part Description Number Number 63001885 S450H SKINPACK 63001975 SPACERS KIT FOR S450H 63000606 SEAL KIT S450H 63001985 RELEASE ASSY S450H 714017 HYDRAULIC OIL FAAC HP 63001875 S450H ENCODER OIL LT. 1 63001965 S450H SHORT PIN...
  • Page 15 DE 7 63000656 S450H RIVETED PISTON 63000706 S450H SPLINED JOINT 63000646 CYLINDER PISTON S450H 63000776 S450H MOTOR CARTER 63000676 S450H CB GEAR FLANGE 903122 ETICH.PET+TRANSPARENT 7090010015 SEAL OR 4.48X1.78 (2018) ARGENTO 45X75 63000756 S450H PLUG SEAL 63001865 FAAC STICKER FOR S450H...
  • Page 16 593-595 COMMUTATING PISTON 63000816 VALVE RING NUT 7090010015 SEAL OR 4.48X1.78 (2018) 7090050015 GASKET OR 10.82X1.78 (2043) 63000676 S450H CB GEAR FLANGE 4404085 STOP VALVE IN ZAMACK 4404095 2006 SUCTION VALVE 7090350025 GASKET OR 34.60X2.62 63000836 VALVE SPACER FOR S450H (3137)
  • Page 17 FAAC S450H Hydraulic Operator Diagram 4: Emergency Lock Release Part Part Description Number 63001985 RELEASE ASSY S450H 7290445 2005 RELEASE HAND GRIP 7090895 21X2 N70B200V SEAL 7131005 KEY MOD. 3889.0913 7275275 CAP FOR LOCK 400/422 RELEASE 2005 63000666 S450H RELEASE PIN...

Table of Contents