Download
Share
Print this page
FAAC S450H Owner's Manual
  1. Manuals
  2. Brands
  3. FAAC Manuals
  4. Gate Opener
  5. S450H
  6. Owner's manual
FAAC S450H Owner's Manual

FAAC S450H Owner's Manual

Automated system for swing-leaf gates
Hide thumbs Also See for S450H:

Advertisement

Quick Links

Download this manual See also: Manual
S450H

Advertisement

loading
Need help?

Need help?

Do you have a question about the S450H and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for FAAC S450H

Summary of Contents for FAAC S450H

  • Page 1 S450H...

  • Page 2: Ce Declaration Of Conformity For Machines

    (DIRECTIVE 2006/42/EC) Manufacturer: FAAC S.p.A. Address: Via Calari, 10 - 40069 Zola Predosa BOLOGNA - ITALY Declares that: Operator mod. S450H is built to be integrated into a machine or to be assembled with other machinery to create a machine under the provisions 2006/42/ of Directive complies with the essential safety requirements of the following EEC directives:...

  • Page 3: Description And Technical Specifications

    S450H 1 DESCRIPTION AND TECHNICAL SPECIFICATIONS 1.1 DIMENSIONS The FAAC S450H automated system for swing-leaf gates consists of an electrical pump and an hydraulic piston transmitting the leaf movement, assembled in a single block. The model with hydraulic lock can automate leaves up to 2 m.
  • Page 4 If the gate structure does not allow the stable fixing of the front fitting, create a firm bearing surface in the leaf structure. - It is advisable to grease all fixing pins - Opening and closing stops must always be installed - Play special attention not to damage the operator rod 3.2 INSTALLATION DIMENSIONS (Dimensions in millimeters) 3.2.1 APPLICATION WITH BRACKET FASTENED TO THE COLUMN ATTENTION: do not cut for any reason the rear bracket Make reference to figures 4 and 5 and to table  to determine the installation position of the operator. Dimensions in millimeters Fig. 4 Fig. 5 Dimensions in millimeters INSTALLATION DIMENSION "B"...
  • Page 5 3.2.2 APPLICATION WITH BRACKET FASTENED TO SIDE WALL ATTENTION: do not cut for any reason the rear bracket Make reference to figures 4 and 5 and to table 2 to determine the installation position of the operator. Dimensions in millimeters Fig.5 Fig.4 Dimensions in millimeters INSTALLATION DIMENSION " B " (SEE FIGURE 4 a°...
  • Page 6 Install the encoder on the rear bracket by correctly engaging 3.3 INSTALLATION OF OPERATORS it on the pin then fix it with the screw and nut supplied (Fig. Check the perfect level then weld the rear fitting to the 8 re. a b c). pillar or fix it by means of suitable screws, dowels / threaded Slightly press the protection cover on the rear bracket to inserts.
  • Page 7 Secure the operator to the front fixing (Fig. 15). Remove the bleed screw (Fig.16 ref. a) paying special attention to leave the sealing O-Ring in its seat If an external mechanical stop point at closure is pre- Install the metallic protection cover as shown in Fig. 16, insert sent, remove the rod comple- and tighten both tie-rods tely and then insert it 5 mm.

  • Page 8: Manual Operation

    5 ELECTRICAL CONNECTION OF THE "2easy bus" ENCODER The S450H operator is fitted with an encoder system with "2easy bus" technology. The proper assignment of the leaf to the corresponding encoder depends on the connection of the two encoder wires (leaf 1- encoder 1; leaf 2 - encoder 2).
  • Page 9 Fig. 19 LEAF * LEAF 2 DL 1 DL 1 THROUGH THE BRACKET COVER OF LEAF THROUGH THE BRACKET COVER OF LEAF DL 2 DL 2 2, VERIFY THAT THE LED DL IS ON WHEN , VERIFY THAT THE LEDS DL AND DL2 DL 3 DL 3 THE MOTOR IS NOT IN OPERATION...
  • Page 10 6 BLEEDING Loosen the tie-rods (Fig. 23 ref. a) and remove the metal protective housing (Fig. 23 ref. b). Remove the upper tie-rod and be careful with the O-ring that must remain it its seat. Fig.23 Remove the screw in Fig. 24 ref.d from the front fitting Remove the joint (Fig.24 ref.f) from the operator stem. (Fig.
  • Page 11 Les descriptions et les illustrations du présent manuel sont fournies à titre indicatif. FAAC se réserve le droit d’apporter à tout moment les modifications qu’elle jugera utiles sur ce produit tout en conservant les caractéristiques essentielles, sans devoir pour autant mettre à...