Table of Contents
Advertisement
CE DECLARATION OF CONFORMITY FOR MACHINES ................................................................................................. 2
WARNINGS FOR THE INSTALLER ................................................................................................................................. 2
1 DESCRIPTION ........................................................................................................................................................ 3
2 TECHNICAL SPECIFICATIONS ................................................................................................................................. 4
3 DIMENSIONS ........................................................................................................................................................ 4
3.1 STANDARD VERSION ........................................................................................................................................ 4
3.2 VERSION WITH MECHANICAL RELEASE ............................................................................................................. 4
4 ELECTRICAL PREPARATIONS ................................................................................................................................... 4
5 INSTALLING THE AUTOMATED SYSTEM ................................................................................................................... 4
5.1 PRELIMINARY CHECKS ..................................................................................................................................... 4
5.2 WALLING IN THE BEARING CASE ...................................................................................................................... 4
5.3 FITTING THE GATE ............................................................................................................................................ 5
5.3.1 OPERATOR CBAC-SB .............................................................................................................................. 5
5.4 INSTALLING THE OPERATOR ............................................................................................................................ 7
5.4.1 OPERATOR WITHOUT MECHANICAL EMERGENCY RELEASE ...................................................................... 7
6.1 ADJUSTMENT OF THE TRAVEL-LIMIT STOPS ...................................................................................................... 8
7 FINAL OPERATIONS ............................................................................................................................................... 9
8 MANUAL OPERATION ............................................................................................................................................. 9
8.1 HYDRAULIC RELEASE OF THE OPERATOR ......................................................................................................... 9
9 MAINTENANCE ...................................................................................................................................................... 10
9.1 OIL LEVEL CHECK ............................................................................................................................................ 10
9.2 BLEEDING OPERATIONS .................................................................................................................................. 10
INDEX
................................................................................................
...................................................................................................................
............................................................................................. 8
(OPTIONAL) .................................................................................................................9
6
7
Advertisement
Table of Contents
Related Manuals for FAAC S700H SB
Summary of Contents for FAAC S700H SB
-
Page 1: Table Of Contents
INDEX CE DECLARATION OF CONFORMITY FOR MACHINES ....................2 WARNINGS FOR THE INSTALLER ..........................2 1 DESCRIPTION ................................ 3 2 TECHNICAL SPECIFICATIONS ..........................4 3 DIMENSIONS ................................ 4 3.1 STANDARD VERSION ............................4 3.2 VERSION WITH MECHANICAL RELEASE ......................4 4 ELECTRICAL PREPARATIONS ........................... -
Page 2: Ce Declaration Of Conformity For Machines
12604 and EN 12605. For non-EU countries, to obtain an adequate level of safety, the 22) Do not allow children, things or adults to stay near the product while it Standards mentioned above must be observed, in addition to national is operating. legal regulations. 23) Keep remote controls or other pulse generators away from children, to 9) FAAC is not responsible for failure to observe Good Technique in prevent the automated system from being activated involuntarily. the construction of the closing elements to be motorised, or for any 24) Transit is permitted only when the automated system is idle. deformation that may occur during use. 25) The user must not attempt any kind of repair or direct action whatever 10) The installation must conform to Standards EN 12453 and EN 12445. -
Page 3: Description
S700H SB - S700H CBAC / 100° - 180°. FAAC S700H is an automated system in a hydraulic enbloc (CLASS III), permitting vehicle access through swing leaf gates which, when installed invisibly in the ground, does not alter the appearance of the gate. -
Page 4: Technical Specifications
Power supply (V dc) Absorbed power (W) 60 (*) Protection class IP 67 Type of oil FAAC HP OIL Operating ambient temperature -20° C +55°C 0 V ~ / 50 Hz Rated Operating Time (R.O.T.) Continous duty at 55°C 5 v ~ / 60Hz... -
Page 5: Fitting The Gate
NOTE: To exploit the operator’s entire rotation, the bearing case must be installed perpendicularly with respect to the closed position of the gate - as shown in Fig. 5. CONTROL UNIT DRAIN PIPE 90° 90° TUBE IN PVC FOR OPERATOR POWER CABLE Fig.5 Fig.8... -
Page 6: Operator Cbac-Sb With Mechanical Release
2) Determine the position of the guide bracket on the support bracket, referring to the leaf rotation axis, as shown in Fig. 15. 3) Accurately weld the guide bracket on the support bracket as shown in Fig. 15, so that the mid-points of the two brackets are aligned with each other. -
Page 7: Installing The Operator
5.4 INSTALLING THE OPERATOR IMPORTANT: REMOVE THE ENCODER BEFORE YOU BEGIN MECHANICAL INSTALLATION 5.4.1 OPERATOR WITHOUT MECHANICAL EMERGENCY RELEASE 1) Take the gate to its open position. 2) Consulting the instructions in chapter 8.1, hydraulically release the operator, using the key (Fig. 1 ref.r) on the release screw (Fig. -
Page 8: Positive Stop - (Internal Mechanical Travel-Limit Stops)
(IMPORTANT FOR CORRECT COUPLING OF THE and closing. PINION-MECHANICAL RELEASE DURING INSTALLATION). FAAC SUPPLIES THE TRAVEL LIMIT DEVICES TOTALLY OPEN ( MAXIMUM 5) Turn the operator pinion with the supplied key (Fig. 1 ref. r), in PINION ROTATION ANGLE ) , the gate closing direction as shown in Fig. -
Page 9: Final Operations
4) Unscrew the travel-limit stop screw (Fig. 20 ref.B) at closing 8.2 MECHANICAL EMERGENCY RELEASE (OPTIONAL) (Fig.20 ref.a), until the leaf begins to move. 5) Fasten the lock-nut of the travel-limit stop screw. For the S700H operator, a manual mechanical emergency 6) Open the leaf, manually taking it into its opening position. -
Page 10: Maintenance
Check oil level periodically by unscrewing the filling plug (Fig.1 ref.g), check if the oil is just below the plug and, if necessary, top up. Topping-up operations must be done only with FAAC HP OIL. OPENING BLEED SCREW 9.2 BLEEDING OPERATIONS THE S700H OPERATOR IS SUPPLIED WITH THE HYDRAULIC CIRCUIT ALREADY AIR FREE.
Need help?
Do you have a question about the S700H SB and is the answer not in the manual?
Questions and answers