Panasonic DF-1100 Service Manual page 171

No. Parameter (see Note3)
00 00 MON/TEL DIAL MON/TEL DIAL
01 01 ALARM STATUS ALARM STATUS
02 02 STOP COMM. JRNL STOP COMM JRNL
03 CONTINUOUS POLL
04 04 NUMERIC ID SET NUMERIC ID SET
05 LANGUAGE
06 06 ID DISPLAY: ID DISPLAY:
07 07 JNL COLUMN JNL COLUMN
08 08 MONITOR MONITOR
09 09 DC LOOP DC LOOP
10 10 TX LEVEL TX LEVEL
11 11 RX LEVEL RX LEVEL
12 12 DTMF LEVEL DTMF LEVEL
13 13 G3 RX EQL G3 RX EQL
14
Not used
15
16 16 PRINT COUNTER PRINT COUNTER
17 17 TX START TX START
18 18 RX START RX START
19 Not used
20 20 ITU T ECM ITU-T ECM
21 21 EP TONE EP TONE
Function Parameter Table
Selections
1 = Monitor
2 = TEL/DIAL
1 = Timer (6 sec.)
2 = Constant
1 = Off
2 = On
1 = Off
2 = Stn (Tx only)
3 = Hub (Rx only)
1 = Off (will not accept)
2 = On (accepts)
1 = Number (Numeric ID)
2 = Chara (Character ID)
1 = Preset station name
2 = Received ID
1 = Off
2 = On
1 = Off (Normal)
2 = On (Off Hook)
00 = 0 dBm
15 = -15 dBm
1 = -43 dBm
2 = -38 dBm
3 = -33 dBm
4 = -48 dBm
00 = 0 dBm
15 = -15 dBm
1 = Off
2 = On
1 = Off
2 = On
1 = 2400 bps
2 = 4800 bps
3 = 7200 bps
4 = 9600 bps
5 = TC7200 bps
6 = TC9600 bps
7 = 12000 bps
8 = 14400 bps
1 = 2400 bps
2 = 4800 bps
3 = 7200 bps
4 = 9600 bps
5 = TC7200 bps
6 = TC9600 bps
7 = 12000 bps
8 = 14400 bps
1 = Off (Invalid)
2 = On (Valid)
1 = Off (without EP Tone)
2 = On (with EP Tone)
Function
Selects whether the machine starts TX automatically
during On-Hook dialing. during On-Hook dialing.
(Monitor: Start TX after pressing START)
(TEL/DIAL: Start TX automatically)
Selects No Paper or No Ink alarm status. If "Constant",
the alarm will not stop until "STOP" is pressed or the the alarm will not stop until "STOP" is pressed or the
error is cleared.
Selects whether the machine prompts to print the
COMM Journal when the printout condition is set to COMM. Journal when the printout condition is set to
INC and STOP is pressed during communication.
Selects whether the Continuous Polling feature is
enabled. enabled.
Stn: When a document is placed on the ADF, the S Wh d i l
remote machine can retrieve it automatically.
Hub: when the polling command is initiated machine Hub: when the polling command is initiated, machine
will continuously poll documents from the remote
stations until it is interrupted by pressing "STOP".
Selects whether the machine accepts to set or change Selects whether the machine acce ts to set or change
Numeric ID.
Selects language. Press " " or " " to select displayed
language. (Used to improve manufacturing productivity.)
Selects the priority of displaying ID. Selects the priority of displaying ID
Selects contents of ID column on Journal. Selects contents of ID column on Journal
Selects Monitor ON/OFF for monitoring fax signals. Selects Monitor ON/OFF for monitoring fax signals.
(FOR SERVICE USE ONLY)
Selects a false Off Hook state for back to back Selects a false Off Hook state for back to back
communication test.
Selects signal output level, 0 to -15 dBm in 1 dBm Selects signal out ut level, 0 to -15 dBm in 1 dBm
steps. ste s.
(R f (Refer to Chapter 4.3) Ch )
Selects receiving sensitivity of -33/-38/-43/-48 dBm. Selects receiving sensitivity of -33/-38/-43/-48 dBm.
( (Refer to Chapter 4.3) )
Selects DTMF output level, 0 to -15 dBm in 1 dBm Selects DTMF output level 0 to 15 dBm in 1 dBm
steps. steps
Select whether the cable equalizer in G3 rece tion Select whether the cable equalizer in G3 reception
mode is On or Off.
Selects whether to print in the Fax Parameter List, the
counter information that is displayed in the Function counter information that is displayed in the Function
Parameter No. 61.
Selects transmission modem start speed,
14400/12000/TC9600/TC7200/ 14400/12000/TC9600/TC7200/
9600/7200/4800/2400 bps. 9600/7200/4800/2400bps
Selects receiving modem start speed, g
14400/12000/TC9600/TC7200/ 14400/12000/TC9600/TC7200/
9600/7200/4800/2400bps 9600/7200/4800/2400 bps.
Select ECM mode. Select ECM mode
Selects echo protect tone on V.29 mode, On (add) or
Off (Not add) Off (Not add).
(Used when Echo Suppression is disabled.)
Test Modes
d h ADF h
( )
5–5