Panasonic DF-1100 Service Manual page 156

Panasonic DF–1100
Code Mode
XMT
301
RCV
331 XMT
400 XMT
401 XMT
402 XMT
RCV
403
(Polling)
404 XMT
405 XMT
RCV
406 (Password
Comm.)
407 XMT
408 XMT
409 XMT
410 RCV
RCV
411
(Polling)
412 G3 RX
RCV
414
(Polling)
XMT
415
(Polling)
416 RCV
4–44
Information Codes
Phase Description of Problem
System fault.
C
8–minutes timer error. (Germany only)
T1 timer (35 5 sec) elapsed without detecting
B
300 bps signal.
DCN was returned from receiver while
B
transmitter is waiting for CFR or FTT.
DCN was returned from receiver while
B
transmitter is waiting for NSF/DIS.
B Transmitter had no polling function.
Transmitter sent NSS (or DCS) followed by
B TCF three times, but the receiver did not
respond. (CFR or FTT is usually returned)
Transmitter received FTT after it transmitted
TCF at 2400bps.
B
Received RTN after communicating at 2400
bps.
XMT–Password mismatched.
B
RCV–Password mismatched.
Selective RCV incomplete.
Transmitter received no response after it
transmitted post message, such as EOP, MPS,
D
EOM, etc.
Or received DCN.
Transmitter received RTN after it transmitted
D
EOP, MPS, or EOM.
Transmitter receives PIN after it transmitted a
D
post message, such as EOP, MPS, EOM, etc.
Received DCN while waiting for post
D
command. (EOP, MPS, EOM, etc.)
B Received DCN after transmitting NSC.
No response within 12 seconds in
B
NSS/DCS/MPS wait state. (After transmitting
D
FTT, MCF, or CFR)
No response received after transmitting 3rd
B
NSC.
Remote side attempted to receive message
from your machine in polling communication.
B
"Inform the remote side that your machine does
not have the polling transmission feature."
Receiver did not detect post command, such
D
as EOP, MPS, EOM, etc.
Cause
Software problem occurred (FCB PCB)
Wrong number is dialed and the START button
is pushed.
Telephone line is disconnected while dialing.
FCB PCB (Modem) or LCE PCB is defective.
Receiver is defective. (It may only be
transmitting CED)
Your machine's ID Number is not programmed.
Possible incompatibility or incorrect Password
(Password Reception, Selective Receive).
Mailbox is full.
Receiver working in non–CCITT mode only.
(Possible incompatibility)
"POLLED=ON" (polling XMT ready) is not set
at the transmitter.
Document to be transmitted is not placed at
the transmitter.
Receiver is defective. (Modem, LCE PCB,
etc.)
FCB PCB or LCE PCB is defective.
Receiver disconnects line during first NSS (or
DCS) is transmitted.
Line quality is poor. (TCF is damaged due to
line noise)
Receiver is defective. (Modem, LCE PCB,
etc.)
FCB PCB or LCE PCB is defective.
XMT, RCV password does not match.
Last 4 digits of TSI does not match with the
last 4 digits of ONE–TOUCH, ABBR telephone
number.
Receiver is defective. (No paper, paper
jamming, etc.)
Receiver ceased receiving because of
excessive error. (Line quality is poor)
FCB PCB (Modem) or LCE PCB is defective.
Receiver receives data with error. (Line quality
is poor)
Receiver is defective. (Modem, LCE, etc.)
FCB PCB or LCE PCB are defective.
Receiver receives data with error due to poor
line quality, and receiving operator requests
voice contact.
Receiver is defective. (Modem, LCE, etc.)
FCB PCB or LCE PCB are defective.
Interface or line is faulty.
Transmitter is defective.
Transmitter is not ready for polling
communication.
Password does not match between transmitter
and receiver.
Transmitter is defective.
FCB PCB is defective.
Password does not match between transmitter
and receiver.
Transmitter is defective. (No document,
document jam, etc.)
Transmitter is defective.
Line quality is poor. (RTC signal is distorted
due to line noise)
FCB PCB or LCE PCB are defective.