Dhp-A - Danfoss DHP-H Installation And Service Instructions Manual

2 .4

DHP-A

Delivery check
1. Check that there is no transport damage. The heat pump is
packaged in cardboard.
2. Remove the plastic wrapping and check that the delivery con-
tains the following components.
DHP-A, sizes 6kW - 10kW:
Part no . Name
Quantity
9680-5796A00 1 Document kit
9674-57902001 1 Transparent book case
9360-47054001 1 Safety valve 9 bar 1/2"
9588-51618001 1 Kimsafe outdoor sensor 200 035
9360-56335001 1 Safety valve 1.5 bar 1/2"
9674-24735001 1 Expansion and bleed tank without valve
9551-54479001 1 Cardboard packaged top for HP
9360-51759007 1 Compression angle joint 28x28 joint
9674-54168001 1 Pipe insulation IT 9x28
3311-55300001 1 Brine in Cu pipe in TWS packaging
9684-48342001 2 Rubber bellows for 22-32mm hole
9674-54164001 1 Pipe insulation F-54-A D=54x9mm
5211-50730A00 2 Flexible hose R25 L=600
9360-55453A00 1 Filling kit DN 25
9360-52488001 1 Dirt filter with shut-off DN25
9360-51738005 2 Straight connection LK 303 28xR25
9360-51738008 4 Straight compression connection 22 xR20
DHP-A, size 12kW:
Part no . Name
Quantity
9680-5796A00 1 Document kit
9674-57902001 1 Transparent book case
9360-47054001 1 Safety valve 9 bar 1/2"
9588-51618001 1 Kimsafe outdoor sensor 200 035
9360-56335001 1 Safety valve 1.5 bar 1/2"
9674-24735001 1 Expansion and bleed tank without valve
9551-54479001 1 Cardboard packaged top for HP
9360-51759007 1 Compression angle joint 28x28 joint
9674-54168001 1 Pipe insulation IT 9x28
3311-55300001 1 Brine in Cu pipe in TWS packaging
9684-48342001 2 Rubber bellows for 22-32mm hole
9674-54164001 1 Pipe insulation F-54-A D=54x9mm
5211-50730A00 2 Flexible hose R25 L=600
9360-56911A00 1 Filling kit DN 32
9360-52488001 1 Dirt filter with shut-off DN25
9360-51738005 4 Straight connection LK 303 28xR25
9360-51738008 2
Straight compression connection 22 xR20
The outdoor unit is supplied as a package containing:
• Outdoor unit
• Disassembled stand
• Necessary screws, nuts and washers.
• Defroster sensor
12
Dimensions and connections
The brine pipes can be connected on either the left or right-hand
sides of the heat pump.
455
596
1
6
7
2
Figure 7: DHP-A, Dimensions and connections .
Position Name
1 Heating system return pipe, 22 Cu: 4-10 kW, 28 Cu: 12-18 kW
2 Heating system supply pipe, 22 Cu: 4-10 kW, 28 Cu: 12-18 kW
3 Hot water pipe, 22 Cu or stainless steel
4 Cold water pipe, 22 Cu or stainless steel
5 Expansion pipe, 22 Cu
6 Brine supply pipe (Brine out), 28 Cu
7 Brine return pipe (Brine in), 28 Cu
8 Lead-in for incoming power supply and sensors
9 Lead-in for communication cable
10 Expansion outlet brine circuit, R25 int.
Figure 8: Outdoor unit, Dimensions and connections .
Position Name
1 Brine in (HP Brine out) 28 Cu
2 Brine out (HP Brine in) 28 Cu
VMBMA102
440
250
40±10
3 4 5 10
80
6
7
8
56
9
74
327
1
2
7
6
2 1
1175