Advertisement
2. SPECIFICATIONS AND TECHNI-
CAL DATA
1.
NAME OF PARTS
2
7
1
4
5
6
0
2.
TOOL SPECIFICATIONS
PRODUCT NO.
TA116/22-9(CE)
HEIGHT
152mm (6'')
WIDTH
48mm (2'')
LENGTH
237mm (8'')
WEIGHT
1kg (2.2Ibs)
RECOMMENDED
5 to 6.9bar
OPERATING PRESSURE
(70 to 100p.s.i)
LOADING CAPACITY
180 Staples
AIR CONSUMPTION
0.31 l (0.011ft
6.9 bar (100p.s.i.)
operating pressure
∗ The machine has been compactly designed in order to im-
prove operating weight balance.
3.
FASTENER SPECIFICATIONS
PRODUCT NO. TA116/22-9(CE)
CROWN
9.3mm (3/8'')
LENGTH
6 to 16mm (1/4'' to 5/8'') 6 to 16mm (1/4'' to 5/8'')
WIDTH
0.77mm (0.030'')
THICKNESS
0.55mm (0.0215'')
GAUGE
22
CROWN
LENGTH
THICKNESS
TOOL AIR FITTINGS:
This tool uses a 1/4" N.P.T. male plug. The inside diameter
should be 7mm (.28") or larger. The fitting must be capable of dis-
charging tool air pressure when disconnected from the air supply.
1 Frame
2 Cylinder Cap
3 Air Exhaust
Port
4 Slider Unit
3
5 Magazine
8
6 Trigger
7 Grip
8 Click Lever
9 Warning Label
(back side)
9
0 Outlet
TA116/21-13(CE)
152mm (6'')
48mm (2'')
237mm (8'')
1kg (2.2Ibs)
5 to 6.9bar
(70 to 100p.s.i)
150 Staples
3
3
) at
0.34 l (0.012ft
) at
6.9 bar (100p.s.i.)
operating pressure
TA116/21-13(CE)
13mm (1/2'')
0.91mm (0.036'')
0.70mm (0.0275'')
21
WIDTH
RECOMMENDED OPERATING PRESSURE:
5 to 6.9 bar (70 to 100 p.s.i.). Select the operating air pressure
within this range for best fastener performance.
DO NOT EXCEED 6.9 bar (100 p.s.i.).
4.
TECHNICAL DATA
NOISE
A-weighted single-event sound power level
TA116/22-9 (CE) ------ LWA, 1S, d 84.9 dB
TA116/21-13 (CE) ------ LWA, 1S, d 86.5 dB
A-weighted single-event emission sound pressure level at
work station
TA116/21-13 (CE) ------ LpA, 1S, d 80.0 dB
These values are determined and documented in accord-
ance to EN12549 : 1999.
5.
APPLICATIONS
∗ Interior decoration
∗ Fastening Plywoods (for interior or furnitures)
∗ Upholstering chair, sofa, and other furnitures
3. AIR SUPPLY AND CONNEC-
TIONS
WARNING
Read section titled "SAFETY INSTRUCTIONS".
[AIR SUPPLY & CONNECTIONS]
Air compressor
Air hose
Used at 5 to 6.9 bar (70 to 100 p.s.i.)
FITTINGS: Install a male plug on the tool which is free flowing
and which will release air pressure from the tool when discon-
nected from the supply source.
HOSES: Hose has a min. ID of 6 mm (1/4") and max. length of
no more than 5 meters (17").
The supply hose should contain a fitting that will provide "quick
disconnecting" from the male plug on the tool.
SUPPLY SOURCE: Use only clean regulated compressed air as
a power source for the tool.
3-PIECE AIRSET (Air filter, Regulator, Oiler):
Refer to TOOL SPECIFICATIONS for setting the correct operat-
ing pressure for the tool.
6
TA116/22-9 (CE) ------ LpA, 1S, d 78.9 dB
Regulator
Air filter
3-piece airset
Oiler
Advertisement
