Page 1
User manual and Spare Parts List GP-510- 446(7) ANITA B, s.r.o. Hliníky 2068 680 01 Boskovice Czech Republic tel: +420 516454774, 516453496 fax: +420 516452751 e-mail: info@anita.cz...
Page 3
GP-510-446(7) 1 Safety Measures Do not put the machine into operation until an appropriate preparation is carried out by a specialist or an authorised person, and until you get acquainted with safety measures. 1. Any sewing machine may be operated only by a properly trained operator.
Page 4
GP-510-446(7) Putting the machine into operation Following instructions must be observed to avoid risk of failures or damage to the machine: - clean the machine of preserving agents - drop 1-2 drops of oil into looper - remove the front cover and oil the ends of needle bar connecting-rod and of the cross-head slide of thread take-up.
Page 5
GP-510-446(7) Threading the Upper Thread Caution! Switch off the main switch and remove your feet from the pedals on the machine support before threading so that the machine may not be started by unintended treading on the pedal. When threading the thread from bobbin stand into needle follow figure 1 for single needle machine.
Page 6
GP-510-446(7) Inserting needles Caution ! Switch off the main switch and remove your feet from the pedals on the machine support before replacing needles so that the machine may not be started by unintended treading on the pedal. Fig.3 Having chosen the right thickness (size) of needle whose system coresponds to the prescribed kind (usually 134 LR) loosen screw (A,fig.3) on needle bar and insert needle (B) as far as it will...
Page 7
GP-510-446(7) Caution! Do not start the machine until you put the hook covers in working (protecting) position. Switch off the main switch and remove your feet from the pedals on the machine support before replacing the hook bobbin so that the machine may not be started by unintended treading on the pedal.
Page 8
GP-510-446(7) 7 Adjusting Differential Feed Ratio (only for machines with driven presser foot) To ensure sewing of fabric layers without their displacement in the course of feeding it is possible to adjust different lengths of feeding driven by press-wheel and feeding by rotary feed dog.
Page 9
GP-510-446(7) The sewing machines are equipped with a safety clutch on the lower shaft (A) fig. 8 that allows the operator to turn the driving part of lower shaft (A) when the loopers or feed dogs are locked. The clutch consists of segment (B) engaging with.groove (C) in the disk on lower shaft by the pressure of two springs.
Page 10
GP-510-446(7) 10 Switching Off and Switching On of the Main Switch The Main Switch are marked 0 and I or they have grey/green and red buttons. Pushing position of the button marked "0" (red) means: off, pushing position of the button marked "I"...
Page 11
GP-510-446(7) 12 Bobbin Winder – Standard Built in Fig. 9 The thread passes from the bobbin stand through thread guide on the winder bracket (1) and between tension disks (2) and then following the direction of arrow (S) to the empty bobbin.
Page 12
GP-510-446(7) Instructions for adjustment threat trimmer mechanism 13 Basic condition a) Clearance between the throat plate and the bobbin case stopper. Fig.10 Condition : Clearance between the top end of the bobbin case resting groove on the throat plate and the top face of the bobbin case stopper of the hook : 1,4 mm .
Page 13
GP-510-446(7) c) The range of technological use Needle: 134 LR size 90 – 180. According to the chosen material, threads and needle gauge it is necessary to choose throat plate insert and also throat plate (table I3- Parts Book) .
Page 14
GP-510-446(7) 16 To adjust the counter knife (Fig. 14)(table I1,J-Parts Book) Counter knife (I1/7) is located on the holder (I1/3). After releasing the screw (I1/19), mildly push the counter knife (I1/7) on the moving knife (I1/20) by the means of the excentric pin (I1/9) which means in the following position : counter knife blade must come into the contact approx.5 mm distance from the front of the moving...
Page 15
GP-510-446(7) 18 To adjust the thread trimming cam (Fig.15)(table J,I1 – Parts Book) Axial position of the trimming c am(J/1) is in contact with the axial ring (J/8). a)Adjust the thread take up lever to top dead point. In this position, adjust the actuating cam using two screws (J/30) so as the revolving pin (J/5,6) is insert into cam closely behind point of finish thread trimming.
Page 16
GP-510-446(7) 20 To adjust the initial position of the moving knife (Fig.16) Adjust the moving knife (I1/20) into the initial position. A clearance of approx. 1 mm must be provided between the top end of the moving knife and of the counter knife.
Presser Foot Bar Mechanism anita-b GP-510-446(7) Part No. Ref.No. Name of Part Q´ty GP/ 119019 G2-1 Presser Bar Bushing (Upper) GP/ 700785 G2-2 Screw (M5x0,8x6) GP/ 119018 G2-3 Presser Bar Bushing (Upper) GP/ 118530 G2-4 Presser Bar Holder GP/ 700510...
Page 42
Right Side Hook Mechanism anita-b GP-510-446(7)
Right Side Hook Mechanism anita-b GP-510-446(7) Part No. Ref.No. Name of Part Q´ty GP/ G400TL H1-1 Hook Complete With Bobbin Case-Large GP/ G400TL-749 H1-1-1 Hook complete without cap GP/ G400TL-102 H1-1-2 Hook without cap holder GP/ G400T-017 H1-1-3 Tension spring fastening screw...
Page 44
Right Side Hook Post Mechanism anita-b GP-510-446(7)
Left Side Post Mechanism anita-b GP-510-446(7) Part No. Ref.No. Name of Part Q´ty I3-1 GP/119145 Cover Plate/kryt I3-2 GP/250084 Screw/šroub(M3x0,5x6) I3-3 GP/SM5-4.9M Support Plate/levý sloupek I3-4 GP/119144 Washer/podložka I3-5 GP/130224 Screw/šroub(M5x0,8x12) I3-6 GP/182451 Screw/šroub(m6x1,0x14) I3-7 GP/119725 Stud/ ep I3-8 GP/317170 Screw/šroub(M4x0,7x10)
Left Side Post and Backtacking Feed Mechanism anita-b GP-510-446(7) Part No. Ref.No. Name of Part Q´ty GP/ SM5-21.3 K2-1 Rod/Rameno SB GP/ SM5-2.10 K2-2 Rod/Rameno SJ GP/ SM5-2.12 K2-3 Rod/rameno ZJ GP/ SM5-2.11 K2-4 Rod/rameno ZB GP/ M5x12 K2-5 Screw/šroub M5x12 DIN 912...