Movie Advance - JVC HR-S9600U Instructions Manual

30
EN
1
MENU
ATTENTION
Movie Advance and Movie Advance (Preview) work only on
prerecorded cassettes that have been recorded in the SP
mode, and have no safety tab. If the VCR detects the EP mode
after you press OK in step 4, the following screen appears.
MOVIE ADVANCE CAN NOT
BE SELECTED FOR EP
RECORDINGS.
PRESS (SKIP) TO CANCEL
Skip Search will work for prerecorded
EP tapes.
When "MOVIE ADVANCE" is selected...
If you want to stop searching for the start of the movie,
simply press SKIP SEARCH or STOP.
When "MOVIE ADVANCE (PREVIEW)" is selected...
If SKIP SEARCH was inadvertently pressed, press it again
to resume normal playback.
While the VCR is searching for the next preview, if you
see a preview you wish to view, press SKIP SEARCH and
the VCR will immediately go to the start of that preview.
If the VCR starts to reverse to a preview you do not wish
to view, press SKIP SEARCH to initiate searching to the
next preview.
NOTES:
Normally there is a period of black and no audio at the
beginning and end of previews. The Movie Advance feature
detects those parts where the picture fades to black and the
audio fades to silence, and initiates fast-motion to skip over
the detected previews.
Some previews may not be detected and Movie Advance may
not work properly.
The setting you selected in step 3 remains in effect until the
cassette is ejected.
"MOVIE ADVANCE (PREVIEW)" does not use TimeScan when
searching for the next preview.
Patents Pending
PLAYBACK AND RECORDING FEATURES (cont.)
SKIP SEARCH
TIME SCAN
OK

MOVIE ADVANCE

Movie Advance
This feature helps you locate certain parts of prerecorded movies
(rented or purchased) and works in two ways.
You can go to the beginning of the movie, skipping over all
previews.
You can fast-motion the tape to the beginning of the next
preview, so you can skip over previews one by one.
LOAD A CASSETTE
1
Insert a cassette that has a prerecorded movie (rented or
purchased), with no safety tab, into the VCR. Playback
begins automatically.
ACCESS SKIP MENU SCREEN
2
Press SKIP SEARCH.
SELECT MODE
3
Press CH 5∞ or TIME
SCAN %fi to move the
highlight bar (arrow) to
your choice.
a– Select "MOVIE
ADVANCE" if you want
to advance directly to
the beginning of the
movie.
b– Select "MOVIE
ADVANCE (PREVIEW)" if you want to advance to
the next preview.
c– Select "SKIP SEARCH"* if you do not want to
perform Movie Advance, then press OK and the
VCR enters stop mode. To activate the Skip Search
function, see page 26.
* If "CA PLAYBACK" is set to "AUTO" or "MANUAL"
( pg. 32), "COMMERCIAL ADVANCE" will be
displayed on the screen instead of "SKIP SEARCH".
PERFORM MOVIE ADVANCE
4
a– If you selected "MOVIE ADVANCE" in step 3 and
press OK, the following screen will appear with a
blue background. The VCR will rewind the
beginning of the tape, then will fast-motion to the
beginning of the movie. "READY" will appear and
blink when the beginning of the movie is detected
and the Stop mode will be engaged. Press PLAY to
view the movie.
MOVIE ADVANCE
SEARCHING FOR BEGINNING
OF MOVIE.
PRESS (STOP) TO CANCEL
b– If you selected "MOVIE ADVANCE (PREVIEW)" in
step 3 and press OK, the VCR will fast-motion to the
beginning of the next preview and normal playback
will resume when it is detected.
Each press of SKIP SEARCH fast-motions to the
beginning of the next preview, thereby skipping over
one preview each time.
The tape will forward-search a little past the start of
the next preview, then will reverse-serach to the
beginning of the preview and start playback.
SKIP MENU
= MOVIE ADVANCE
MOVIE ADVANCE (PREVIEW)
SKIP SEARCH
PRESS (5,∞), THEN (OK)
PRESS (SKIP) TO CANCEL
MOVIE ADVANCE
READY
PRESS (PLAY) TO START
PRESS (STOP) TO CANCEL