Installing Your New Vcr; Connections; Basic Connections - JVC HR-S9600U Instructions Manual

6
EN

Connections

Antenna or Cable
AC Outlet
AC Power
Cord
CABLE
BOX
S VIDEO
IN OUT
Back of VCR
AUDIO
OUT
Audio/Video
Cable (supplied)
TV
NOTES:
The VCR channel is the channel on the TV which will display
the audio and video signals from the VCR. The VCR's CH3-
CH4 switch, on the back of the VCR, sets the VCR channel to
CH3 or CH4.
The CH3–CH4 switch is preset to the CH3 position.
Set to CH4 if CH3 is used for broadcasting in your area and
set the channel on the TV to correspond to the VCR's CH3–
CH4 switch setting.
If you have connected your VCR to the TV using the RF
connector, you may need to press the TV's CH UP and then CH
DOWN when switching between the TV and VCR input modes,
to maintain good picture quality.
Even if you are using AV cables to connect your VCR to your
TV, you must also connect it using the RF cable. This will
ensure that you can record one show while watching another
( pg. 39).
For full identification of the VCR's rear panel, refer to the
Index (REAR VIEW
ANTENNA IN
(Antenna or Cable input)
Coaxial Cable
Flat Feeder
Matching
Transformer
(Not supplied)
IN OUT
ANTENNA
R
AUDIO
REMOTE AV
VHF/UHF
PAUSE COMPULINK
L
(MONO) TV
CH3
VIDEO CH4
VIDEO
OUT
75 ohm terminal
Back of VCR
CH3
CH4
pg. 71).

INSTALLING YOUR NEW VCR

Basic Connections

CHECK CONTENTS
1
Make sure the package contains all of the accessories
listed in "SPECIFICATIONS" (
SITUATE VCR
2
Place the VCR on a stable, horizontal surface.
CONNECT VCR TO TV
3
The connection method you use depends on the type of
TV you have.
RF Connection
IN
OUT
TV OUT
AV Connection
RF Cable
(supplied)
S-VIDEO Connection
CONNECT VCR TO
POWER SOURCE
4
Connect the power plug to an AC outlet.
FINAL PREPARATION FOR
USE
5
Power on the VCR and if you have connected the VCR
to the TV using the RF connector, select the VCR
channel (3 or 4) by setting the switch on the rear of the
VCR as shown in the illustration.
You can now perform simple playback (
simple recording (
To Connect To A TV With NO AV Input Terminals . . .
a– Disconnect the TV antenna from the TV.
b– Connect the TV antenna cable to the ANTENNA
IN jack on the rear of the VCR.
c– Connect the supplied RF cable between the TV
OUT jack on the rear of the VCR and the TV's
antenna terminal. Set TV on CH3 or CH4
corresponding to the CH3 – CH4 switch setting on
the back of the VCR.
To Connect To A TV With AV Input Terminals . . .
a– Connect the antenna, VCR and TV as shown in
the illustration.
b– Connect an Audio/Video Cable between the AUDIO
OUT and VIDEO OUT jacks on the rear of the VCR
and the AV IN jacks on the TV. Set your TV in video
input mode or A/V input mode. Refer to the TV
Instruction Manual.
If you have a TV with S-VIDEO input terminals, see
"S-VIDEO Connection" on page 7.
The clock and tuner channels will automatically be
set when the antenna is connected and when the AC
is first connected to the VCR (
(If "Auto" or "CH" is displayed on the front display
panel before the VCR is powered on, the clock and
tuner channels are being set automatically. Wait for
the time to be displayed on the front display panel
before powering on the VCR.)
pg. 22).
pg. 73).
pg. 8).
pg. 21) or