Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Installation Manual
Advertisement
Table of Contents
Related Manuals for Yeastar Technology MyPBX U510
Summary of Contents for Yeastar Technology MyPBX U510
- Page 1 MyPBX U510 Installation Guide MyPBX U510 Installation Guide Version: V1.0 Yeastar Technology Co., Ltd Date: 25 , July, 2012 http://www.yeastar.com 1/14...
-
Page 2: Table Of Contents
3.2.3 Connection of FXS ports ....................10 3.2.4 Power Connection ......................10 3.2.5 Overall Flow Chart ......................11 4. MYPBX U510 BASIC CONFIGURATIONS ..................11 4.1 Factory Defaults ....................... 11 4.2 Logging in the Web Configuration Panel ................. 11 4.3 Network Settings ......................12 4.4 Extensions Setup and management ................. -
Page 3: Preparation Before Installation
This Guide explains how to install MyPBX U510, how to configure MyPBX U510 via web interface, how to add extensions, and make/receive calls via PSTN lines. -
Page 4: Hardware Specifications
MyPBX U510 Installation Guide Screws 8 screws (φ3.0*6mm) for mounting ears; 4 screws (φ3.0*8mm) for hard disk brackets Sheet 1 MyPBX U510 Packing List 2. Hardware Specifications 2.1 Overview Figure 2-1 MyPBX U510 2.2 LED Indicators and Ports Figure 2-2 MyPBX U510 Front Panel http://www.yeastar.com... - Page 5 MyPBX U510 Installation Guide Figure 2-3 MyPBX U510 Back Panel Indication Status Description Power Power status The power is switched on The power is switched off MyPBX status Blinking MyPBX is running properly Not Blinking/Off MyPBX goes wrong 1-16 FXO port status Red light The red light is blinking: the PSTN line hasn’t been...
-
Page 6: Specifications And Operating Environment
MyPBX U510. 3.1 Placement Instructions Ambient Temperature: to avoid overheating, please do not run MyPBX U510 in the place where the ambient temperature is above 122℉ (50℃). Ventilation: please make sure that the device has good ventilation around. -
Page 7: Installation Instructions
ADSL modem. LAN Port Connection Connect one end of a network cable to the LAN port of MyPBX U510, and the other end to any port of company’s LAN switch/router. If the LAN port is connected to PC directly (not via a switch), please use cross-over cable. - Page 8 MyPBX U510 Installation Guide When connected to the E1 line, RX- of E1 port should be connected to TX- of E1 line; RX+ of E1 port should be connected to TX+ of E1 line; TX- of E1 port should be connected to RX- of E1 line; TX+ of E1 port should be connected to RX+ of E1 line.
- Page 9 3. Connection of GSM/UMTS ports If No.3 and No.7 connectors are GSM/UMTS Ports, the steps of connection are as below: Step 1: Open the Upper case of MyPBX U510 Step 2: Insert the SIM card: Figure 3-4 Inserting the SIM Card Step 3: Connect the antenna Once completed, the No.3 and No.7 LED lights would turn red as below figure:...
-
Page 10: Connection Of Fxs Ports
Once users have made sure that device installation, cable connection and power type is correct, please switch on the power. Then MyPBX U510 will start booting. In the meantime, users would see that the ‘POWER’ and ‘RUN’ indicator lights would turn on. -
Page 11: Overall Flow Chart
Figure 3-8 Overall Flow Chart 4. MyPBX U510 Basic Configurations 4.1 Factory Defaults MyPBX U510 provides web-based configuration interface for administrator and account user. The user can manage the device by log in the web interface. The factory default IP address: LAN: 192.168.5.150;... -
Page 12: Network Settings
MyPBX U510 Installation Guide Figure 4-1 MyPBX Web Configuration Panel Login Page Enter the Admin User Name and Password to log in. Figure 4-2 MyPBX Admin Configuration Interface Via the configuration interface, the admin can make all the system configurations, including network settings (LAN, WAN, Firewall, VPN, DDNS, VLAN, etc.);... -
Page 13: Extensions Setup And Management
MyPBX U510 Installation Guide just configuring the IP address of the LAN port which is connected to the local area network of the company is OK. WAN Settings Click “Network Settings”->”WAN Settings” on the left menu bar. 1. If the network that the WAN port is connected to is using DHCP server as connection method, please select the “DHCP”... -
Page 14: Making/Receiving Calls
Note: After resetting, all the configurations made by the admin would be erased. 5. Conclusion This Installation Guide only explains the installation and basic settings of MyPBX U510 for making and receiving calls. For more functionality and advanced settings of MyPBX U510, please refer to the relative documents as below: “MyPBX U510 Datasheet”...