System Exclusive Messages - Roland JX-305 Owner's Manual

Channel Aftertouch
status 2nd byte
DnH vvH
* Not received when the Rx Switch parameter is OFF.
* The effect will apply according to the Aftertouch Control setting.
Pitch Bend Change
status 2nd byte 3rd byte
EnH llH mmH
mm,ll=Pitch Bend value: 00 00H–40 00H–7F 7FH (-8192–0–+8191)
* Not received when the Rx Switch parameter is OFF.
* The effect will apply according to the Pitch Bend Control setting.
Channel Mode messages
All Sound Off (Controller number 120)
status 2nd byte 3rd byte
BnH 78H 00H
* When this message is received, all notes currently sounding on the corresponding
channel will be turned off.
* Not received when the Rx Switch parameter is OFF.
Reset All Controllers (Controller number 121)
status 2nd byte 3rd byte
BnH 79H 00H
* Not received when the Rx Switch parameter is OFF.
* When this message is received, the following controllers will be set to their reset val-
ues.
Controller Reset value
±0 (center)
Pitch Bend Change
Polyphonic Key Pressure 0 (off)
Channel Pressure 0 (off)
Modulation 0 (off)
Expression 127 (maximum)
Hold 1 0 (off)
Sostenuto 0 (off)
Soft 0 (off)
Hold 2 0 (off)
RPN Unset. Previously set data will not change.
All Note Off (Controller number 123)
status 2nd byte 3rd byte
BnH 7BH 00H
* When All Note Off is received, all currently sounding notes of the corresponding chan-
nel will be turned off. However if Hold 1 or Sostenuto are on, the sound will be held
until these are turned off.
* Not received when the Rx Switch parameter is OFF.
Omni Off (Controller number 124)
status 2nd byte 3rd byte
BnH 7CH 00H
* The same processing as when All Note Off is received will be done.
* Not received when the Rx Switch parameter is OFF.
Omni On (Controller number 125)
status 2nd byte 3rd byte
BnH 7DH 00H
* The same processing as when All Note Off is received will be done. The instrument
will not be set to OMNI ON.
* Not received when the Rx Switch parameter is OFF.
238
Mono (Controller number 126)
status 2nd byte 3rd byte
BnH 7EH mmH
mm=Mono number: 00H–10H (0–16)
* The same processing as when All Note Off is received will be done, and the Solo
Switch parameter will be set to ON.
* Not received when the Rx Switch parameter is OFF.
Poly (Controller number 127)
status 2nd byte 3rd byte
BnH 7FH 00H
* The same processing as when All Note Off is received will be done, and the Solo
Switch parameter will be set to OFF.
* Not received when the Rx Switch parameter is OFF.
System Realtime messages
Timing Clock
status
F8H
* This is received when Sync Mode is SLAVE. Settings can be made to synchronize or
the LFO rate or the effect rate.
Active Sensing
status
FEH
* When an Active Sensing message is received, the unit will begin monitoring the inter-
val at which MIDI messages are received. During monitoring, if more than 420 ms
passes without a message being received, the same processing will be done as when
All Sound Off, All Note Off, and Reset All Controllers messages are received. Then
monitoring will be halted.

System Exclusive messages

status data byte status
F0H iiH, ddH, ......, eeH F7H
F0H: System Exclusive message status
ii = ID number: This is the ID number (manufacturer ID) that specifies the manufac-
turer whose exclusive message this is. Roland's manufacturer ID is
41H.ID numbers 7EH and 7FH are defined in an expansion of the
MIDI standard as Universal Non-realtime messages (7EH) and
Universal Realtime Messages (7FH).
dd,..., ee = data: 00H–7FH (0–127)
F7H: EOX (End Of Exclusive) This is the last status of system exclusive
message.
Universal Non-realtime System Exclusive Messages
Inquiry Request Message
Status Data byte Status
F0H 7EH, dev, 06H, 01H F7H
Byte Explanation
F0H Exclusive status
7EH ID number (universal non-realtime message)
dev Device ID (dev:10H(17)-1FH(32))
06H Sub ID#1 (General Information)
01H Sub ID#2 (Inquiry Request)
F7H EOX (End Of Exclusive)
* The "dev" is own device number or 7FH (Broadcast)
* When Inquiry Request is received, Inquiry Reply message will be transmitted.