System Exclusive Messages; Program Change - Roland JV-1010 Owner's Manual

RPN MSB/LSB (Controller number 100, 101)
status 2nd byte
BnH 65H
BnH 64H
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
mm=MSB of the parameter number specified by RPN
ll=LSB of the parameter number specified by RPN
<<< RPN >>>
Control Changes include RPN (Registered Parameter Numbers), which are extended
parameters whose function is defined in the MIDI specification.
When using RPNs, first the RPN (Controller numbers 100 and 101; they can be sent in any
order) is transmitted to specify the parameter you wish to control. Then, Data Entry
messages (Controller numbers 6 and 38) are used to set the value of the specified parameter.
Once a RPN parameter has been specified, all further Data Entry messages on that channel
are considered to apply to that specified parameter. In order to prevent accidents, when the
desired setting has been made for the parameter, it is recommended that RPN be set to Null.
This device transmits the following RPNs.
RPN Data entry
MSB LSB MSB LSB
00H 00H mmH -
00H 01H mmH llH
00H 02H mmH -

Program Change

status 2nd byte
CnH ppH
n=MIDI channel: 0H - FH (ch.1 - ch.16)
pp=Program number: 00H - 7FH (prog.1 - prog.128)
3rd byte
mmH
llH
Notes
Pitch Bend Sensitivity
mm: 00H - 0CH (0 - 12 semitones)
ll: ignored (processed as 00H)
Up to 1 octave can be specified in semitone steps.
* The Bend Range Up/Down will also be
changed.
* Not received by the Rhythm Part (Part 10).
Channel Fine Tuning
mm, ll: 20 00H - 40 00H - 60 00H
(-4096 x 100 / 8192 - 0 - +4096 x 100 / 8192 cent)
* In Patch mode, the Master Tune (SYSTEM)
will change.
* In Performance mode, the Fine Tune
(PERFORM) of each Part will change. When
received on the Control channel, the Master
Tune (SYSTEM) will change.
Channel Coarse Tuning
mm: 10H - 40H - 70H (-48 - 0 - +48 semitones)
ll: ignored (processed as 00H)
* Not received in Patch mode.
* In Performance mode, the Coarse Tune
(PERFORM/PART) of each Part will change.
MIDI Implementation

System Exclusive Messages

There is a kind of the Universal Non-realtime messages and the Data Set (DT1) messages in
the System Exclusive messages transmitted by this device.
* The device ID number of this instrument is fixed at 10H (17).
Universal Non-realtime System Exclusive Messages
Identity Reply Message
When Identity Request message (p. 71) is received, this message will be transmitted.
status data byte
F0H 7EH, dev, 06H, 02H, 41H, 6AH, 00H,
05H, 00H, 00H, 00H, 00H, 00H
Byte Remarks
F0H Exclusive status
7EH ID number
dev device ID
06H sub ID#1
02H sub ID#2
41H ID number
6AH 00H Device family code
05H 00H Device family number code
00H 00H 00H 00H Software revision level
F7H EOX
Data Transmission
Data Set1 DT1
status data byte
F0H 41H, dev, 6AH, 12H, aaH, bbH,
ccH, ddH, eeH, ... ffH, sum
Byte Remarks
F0H Exclusive status
41H ID number
dev device ID
6AH model ID
12H command ID
aaH address MSB
bbH address
ccH address
ddH address LSB
eeH data:
: :
ffH data
sum checksum
F7H EOX
* The amount of data transmitted at one time is fixed for the type of data, and the data will
be transmitted with the fixed starting address and size. Refer to the address and size
given in "Parameter Address Map" (p. 74).
* Large amounts of data must be divided into packets of 128 bytes or less, and transmitted
at intervals of approximately 20 ms.
* For the checksum, refer to (p. 86).
status
F7H
(Universal Non-realtime message)
(dev: 10H)
(General Information)
(Identity Reply)
(Roland)
(End Of Exclusive)
status
F7H
(Roland)
(dev: 10H)
(JV-1010)
(DT1)
The actual data to be transmitted. Multi-byte
data is transmitted in the address order.
(End Of Exclusive)
73