Table of Contents
Advertisement
Menu Operations
Setting and Adjusting Other Functions (OPTIONS)
Various functions are provided as shown in the "Options 1" and "Options 2" submenus.
You can set or adjust each function, as required.
1
Press the MENU button.
The main menu appears on the screen.
2
Select "Options" with the cursor button 5 5 5 5 or ∞ ∞ ∞ ∞ , and press 3 3 3 3 or the ENTER button.
The "Options 1" submenu appears on the screen.
Options 1
Menu display
15sec
ON
Line display
5sec
OFF
Keystone
ENTER
PC 2 (BNC)
RGB
YP
P
B
R
Options 2
ENTER
3
Select the item to be adjusted with the cursor button 5 5 5 5 or ∞ ∞ ∞ ∞ .
4
Make adjustment with the cursor 2 2 2 2 or 3 3 3 3 .
• While the keystone item is selected, press the ENTER button to display the "Keystone" submenu.
• To enter the "Options 2" submenu, select "Options 2" with the cursor button 5 or ∞, and press the ENTER button.
• To return to the "Options 1" submenu from the "Options 2" submenu, select "Options 1" with the cursor button 5 or ∞,
and press the ENTER button.
Options 1
Menu display
15sec
ON
Line display
5sec
OFF
Keystone
ENTER
PC 2 (BNC)
RGB
YP
P
B
R
Options 2
ENTER
*To adjust multiple items, repeat 3 to 4.
*To reset the keystone (trapezoidal distortion of the picture image) to the original setting, press the PRESET button when
the "Keystone" submenu appears on the screen.
52
Keystone
123
Options 2
Right Left rev.
OFF
ON
Top Bottom inv.
OFF
ON
RS-232C [bps]
9600
19200
15
30
60
OFF
Sleep time [min]
Options 1
ENTER
Adjustment item
Button
Sets whether to clear the menu display automatically or not.
2 or 3
Menu display
15sec* : Clears the display automatically in about 15 seconds.
ON
: Does not automatically clear the menu display.
Sets whether to show the line display (Y/C, VIDEO, PC1, or PC2) on top right of the
screen or not when the VIDEO or PC button is pressed.
2 or 3
Line display
5sec* : Shows the line display for about 5 seconds.
OFF
: Does not show the line display.
Press the ENTER button to enter the keystone submenu.
In the keystone submenu, press 2 or 3 to correct trapezoidal distortion of the
projected image. (–80
Keystone
ENTER
To reset the keystone (trapezoidal distortion of the picture image) to the original
setting (factory set value: 0), press the PRESET button when the "Keystone"
submenu appears on the screen.
To exit the keystone submenu, press the ESCAPE button.
Sets the input signal source according to the device connected to the PC 2 terminals.
However, the input will be RGB irrespective of the PC signal setting.
2 or 3
PC2 (BNC)
RGB* : For a device with analog RGB, V, H/Cs signals
YP
P
: For a device with component (Y, B-Y, R-Y) or DTV-format (Y, P
B
R
signals
Reverses image right-to-left.
2 or 3
Right Left rev.
OFF* : For the front method.
ON
: For upside-down hanging from the ceiling.
Inverses image upside-down.
2 or 3
Top Bottom inv.
OFF* : For normal setup.
ON
: For upside-down hanging from the ceiling.
Sets the baud rate for transmission.
2 or 3
RS-232C [bps]
9600
: 9600 bps
19200* : 19200 bps
Sets the length of sleep time which automatically brings the projector into stand-by
2 or 3
Sleep time [min]
state. You can select one of the sleep times: 15, 30, 60 and 0 (OFF*) minutes.
* Factory set value
5
Press the ESCAPE button to return to the previous menu or press the MENU button
to exit the menu mode.
Note
• Refer to "Removing the Trapezoidal Distortion of the Image" on page 34 for more details about adjusting the keystone.
CAUTION
• Correctly set the "PC2 (BNC)" according to the device connected to the PC2 terminals. However, when the PC signal is
input, RGB input is used irrespective of which setting (YP
P
B
Menu Operations
Adjustment content
0*
+128)
, P
)
B
R
) is made.
R
53
Advertisement
Table of Contents
Troubleshooting
