Select The Input Source To Be Projected; Adjust The Screen Size (Zooming); Adjust Focus; Adjusting Sound Volume - JVC DLA-M2000LU Operating Instructions Manual

Basic Operations
Projector's buttons
STAND BY
LAMP TEMP
OPERATE
HIDE
PC
KEYSTONE VOLUME
VIDEO
PRESET MENU
ESCAPE ENTER
Remote control unit
PRESET MENU
ESCAPE VIC SELECT
PC
+
DIGITAL
ZOOM KEYSTONE VIDEO
–
U T +
SHIFT ZOOM FOCUS
–
D W
+ +
QUICK
SHUTTER ALIGN. VOLUME
– –
Language display
The display languages of the menus, direct buttons
(DIGITAL ZOOM, KEYSTONE, VOLUME, etc) and
messages is set to "ENGLISH" when the projector is bought.
The display language can be selected from the following 6
languages: " (Japanese)", "English (English)",
"Deutsch (German)", "Español (Spanish)", "Italiano (Italian)"
and "Français (French)". (Refer to page 45.) However, some
words (VIDEO, NTSC, Quick Alignment, etc) are only
displayed in English.
32

2. Select the Input source to be Projected

Press the VIDEO button or the PC button to switch the
input.
• Each time you press either button, the selected input
changes as follows. The selected name appears on the top
right of the image on the screen for five seconds. (Called
line display.)
When you press the VIDEO button:
Y/C VIDEO
When you press the PC button:
PC1 PC2
Remote control unit Projector
PC
PC
VIDEO
VIDEO
[Screen display]
VIDEO
PC 1
Q U I C K A L I G N M E N T
PC 2
Y/C
VIDEO
* To show the line display (Y/C, VIDEO, PC1, or PC2) or not
is selectable by the menu. Refer to "Setting and Adjusting
Other Functions (OPTIONS)" on page 52.
Notes
• When the AV IN (Y/C or VIDEO input) terminal input signal
source is switched with the VIDEO button, it is necessary to
reconnect the audio cable to the active device since the
projector has only a single AUDIO input terminal.
• When the PC1 or PC2 input terminal signal source is
switched with the PC button, it is necessary to reconnect
the audio cable to the active device since the projector has
only a single PC AUDIO input terminal.
• When no image signal is input to the selected input
terminal, the message "No image signal is inputted." is
displayed on the screen. (Refer to page 64.)
• When the PC2 input terminal is used, "PC2 (BNC)" must be
selected from the menu options. (Refer to page 52.)

3. Adjust the Screen Size (Zooming)

How to adjust the projected screen size differs depending on
the lens unit (optional) you are using.
GL-M2910G (without zooming function):
The projected screen size cannot be changed.
GL-M2915SG/GL-M2920ZG/GL-M2930SZG (with
zooming function):
Adjust the projected screen size with the following buttons on
the remote control unit.
Projector's buttons
STAND BY
LAMP TEMP
OPERATE
HIDE
PC
KEYSTONE VOLUME
VIDEO
PRESET MENU
ESCAPE ENTER
Remote control unit
FREEZE OPERATE
HIDE
PRESET MENU
ESCAPE VIC SELECT
PC
+
DIGITAL
ZOOM KEYSTONE VIDEO
–
+
U T
SHIFT ZOOM FOCUS
D W –
+ +
QUICK
SHUTTER ALIGN. VOLUME
– –
RM-M2000 REMOTE CONTROL UNIT
Basic Operations
Note
• The function of GL-M2915SG is to adjust the view angle
zooming by 2%. (For fine view angle adjustment)
To enlarge the projected screen size
Press the ZOOM W (Wide) button.
To reduce the screen size
Press the ZOOM T (Tele) button.
Remote control unit
T
ZOOM
W

4. Adjust Focus

Adjust focus with the following buttons on the remote control
unit.
To focus on farther points
Press the FOCUS + button.
To focus on nearer points
Press the FOCUS – button.
Remote control unit
+
FOCUS
–

5. Adjusting Sound Volume

Adjust sound volume with the VOLUME +/– buttons. When
the VOLUME + or – button is pressed, "Audio-Vol" appears
on the screen together with the level bar and set value (0 to
50). When "15 sec." is displayed in the menu, "Audio-Vol" will
appear in approximately 15 seconds.
Audio - Vol 12
When you press the VOLUME + button:
The sound volume becomes higher. (0 50)
When you press the VOLUME – button:
The sound volume becomes lower. (50 0)
* When the volume is set to 0, no sound will be heard from
the built-in speaker.
Remote control unit Projector
+
+
VOLUME
VOLUME
–
–
Notes
• When "Audio-Vol" is displayed on the screen, pressing the
PRESET button resets the set value to "0".
• Press the ESCAPE button to immediately remove the
volume display.
33