Setting And Adjusting Other Functions (Options) - JVC DLA-G150CLU Operating Instructions Manual

Menu Operations

Setting and Adjusting Other Functions (OPTIONS)

Various functions are provided as shown in the "Options 1" and "Options 2" submenus.
You can set or adjust each function, as required.
1
Press the MENU button.
The main menu appears on the screen.
2 Select "Options" with the cursor button 5 5 5 5 or ∞ ∞ ∞ ∞ , and press 3 3 3 3 or the ENTER button.
The "Options 1" submenu appears on the screen.
Options 1
Menu display 15sec ON
Line display 5sec OFF
Lamp time display ON OFF
Keystone ENTER
Lamp control ENTER
Page 2
ENTER
3 Select the item to be adjusted with the cursor button 5 5 5 5 or ∞ ∞ ∞ ∞ .
4 Make adjustment with the cursor 2 2 2 2 or 3 3 3 3 .
• While the keystone item is selected, press the ENTER button to display the "Keystone" submenu.
• To enter the "Page 2" submenu, select "Page 2" with the cursor button 5 or ∞, and press the ENTER button.
• To return to the "Page 1" submenu from the "Page 2" submenu, select "Page 1" with the cursor button 5 or ∞, and press
the ENTER button.
Options
ENTER
Menu display 15sec ON
Line display 5sec OFF
Lamp time display ON OFF
Keystone ENTER
ENTER
Lamp control ENTER
Page 2
ENTER
ENTER
ENTER
ENTER
Flip H
Flip V
RS-232C [bps]
Sleep time [min]
Page 1
*To adjust multiple items, repeat 3 to 4.
*To reset the keystone (trapezoidal distortion of the picture image) to the original setting, press the PRESET button when
the "Keystone" submenu appears on the screen.
54
All manuals and user guides at all-guides.com
Keystone 123
Lamp control
Normal
LPC
LOC
Page 2
OFF ON
OFF ON
9600 19200
15 30 60 OFF
ENTER
Adjustment item Button
Sets whether to clear the menu display automatically or not.
2 or 3
Menu display 15sec* : Clears the display automatically in about 15 seconds.
ON : Does not automatically clear the menu display.
Sets whether to show the line display (Y/C, VIDEO, COMP, PC1, PC2 or DVI) on top
right of the screen or not when the VIDEO or PC button is pressed.
2 or 3
Line display
5sec* : Shows the line display for about 5 seconds.
OFF : Does not show the line display.
Displays the lamp use time.
ON* : Displays when the lamp use time reaches 1000 hours when set in the LPC or
2 or 3
Lamp time display LOC mode.
OFF : Does not display when the lamp use time reaches 1000 hours when set in the
LPC or LOC mode.3
Press the ENTER button to enter the keystone submenu.
In the keystone submenu, press 2 or 3 to correct trapezoidal distortion of the
projected image. (–80 ↔ 0* ↔ +128)
Keystone ENTER To reset the keystone (trapezoidal distortion of the picture image) to the original
setting (factory set value: 0), press the PRESET button when the "Keystone"
submenu appears on the screen.
To exit the keystone submenu, press the EXIT button.
Press ENTER to enter the lamp control submenu.
Normal* : Used as a normal lamp.
LPC : Automatically controls the power used by the lamp and increases it in
steps. When this mode is used, the brightness starts at approximately
70%. The decrease in brightness is slower than in "Normal" mode and this
mode is best suited when using the projector continuously for long periods
of time.
Lamp control ENTER
* "Lamp replacement" appears on the screen when the lamp use time
exceeds 2000 hours.
LOC : The brightness can be set in seven levels (-6 to 0). Since the brightness
can be set in steps, this is the mode best suited for adjusting multiple
screens. This setting can also be changed while the projector is being
used. To change the setting, choose LOC with the 5/∞ cursors and
choose the level with the 2/3 cursors.
Reverses image right-to-left.
2 or 3
Flip H OFF* : For the front method.
ON : For upside-down hanging from the ceiling.
Inverses image upside-down.
2 or 3
Flip V OFF* : For normal setup.
ON : For upside-down hanging from the ceiling.
Sets the baud rate for transmission.
2 or 3
RS-232C [bps] 9600 : 9600 bps
19200* : 19200 bps
Sets the length of sleep time which automatically brings the projector into stand-by
2 or 3
Sleep time [min]
state. You can select one of the sleep times: 15, 30, 60 and 0 (OFF*) minutes.
* Factory set value
5
Press the EXIT button to return to the previous menu or press the MENU button to
exit the menu mode.
Note
• Refer to "Removing the Trapezoidal Distortion of the Image" on page 35 for more details about adjusting the keystone.
Menu Operations
Adjustment content
55