Turning Off Image And Sound (Hide); Removing The Trapezoidal Distortion Of The Image; Quick Alignment Function; (Quick Align.) - JVC DLA-M2000LU Operating Instructions Manual

Basic Operations
Projector's buttons
STAND BY
LAMP TEMP
OPERATE
HIDE
HIDE
button
PC
KEYSTONE
KEYSTONE VOLUME
/ button
VIDEO
PRESET MENU
PRESET
button
ESCAPE
button
ESCAPE ENTER
Remote control unit
FREEZE OPERATE
HIDE
HIDE
PRESET
PRESET MENU button
button
ESCAPE
ESCAPE VIC SELECT
button
PC
+
KEYSTONE
DIGITAL ZOOM KEYSTONE VIDEO
/ button
–
U T +
SHIFT ZOOM FOCUS
D W –
+ +
QUICK
SHUTER ALIGN. VOLUME
– –
RM-M2000 REMOTE CONTROL UNIT
34

Turning off Image and Sound (HIDE)

Video image and audio sound can be temporarily turned off.
Press the HIDE button once:
Video image and audio sound instantly turn off.
Press the HIDE button again:
Video image and audio sound come on again.
Remote control unit Projector
HIDE
HIDE
Note
• When the projected image input is changed, the HIDE
function is canceled and the image and sound return.
Removing the Trapezoidal Distortion of
the Image
If the image projected on the screen is distorted in trapezoid
form, correct it with the KEYSTONE buttons on the projector.
When the KEYSTONE button is pressed, "Keystone"
appears on the screen together with the level bar and set
value (–80 to 128). When "15 sec." is displayed in the menu,
"Keystone" will appear in approximately 15 seconds.
Keystone 123
When you press the KEYSTONE button:
The trapezoid form is corrected as shown in the figure.
When you press the KEYSTONE button:
The top bottom inverted trapezoid form is corrected as
shown in the figure.
* To cancel correction and restore the original screen, press
the PRESET button. (Adjusted value:0)
* Press the ESCAPE button to immediately remove the
keystone display.
Remote control unit Projector
KEYSTONE
KEYSTONE
KEYSTONE
KEYSTONE
Notes
• The trapezoidal distortion (keystone) can be adjusted from the
option menu. (Refer to page 52.)
• The range of the trapezoidal distortion adjustment is
approximately 20° in the vertical direction.
• Interference patterns may appear on the screen when
adjusting the keystone. This is not a malfunction.
• Depending on the type of signal, some noise may appear in
the picture when the keystone is adjusted.
This is not a malfunction.
Remote control unit
FREEZE
OPERATE
HIDE
PRESET MENU
ESCAPE VIC SELECT
PC
+
DIGITAL
ZOOM KEYSTONE VIDEO
–
+
U T
ZOOM FOCUS
SHIFT
D W –
+
+
QUICK
SHUTTER ALIGN. VOLUME
– –
RM-M2000 REMOTE CONTROL UNIT
Basic Operations

Quick Alignment Function

(QUICK ALIGN.)

The Quick Alignment function automatically adjusts (sets)
the screen settings of the image input from the PC1 or PC2
input terminals. This can only be performed from the remote
control.
While projecting an image on the screen, press the QUICK
ALIGN. button on the remote control.
Quick alignment is conducted to obtain best image.
* During the automatic alignment, "Quick Alignment" appears
on the screen, and then disappears when the alignment is
completed.
Remote control unit
QUICK
ALIGN.
[Screen display]
Q u i c k A l i g n m e n t
Notes
• This only works for the signals input from the PC1 or PC2 input
terminals. It does not work for the signals input from the AV IN
terminal (VIDEO or Y/C input terminal).
• The quick alignment function is used to automatically adjust
the "Brightness", "Contrast", "Horizontal and vertical
position", "Phase" and "Tracking" of the projected image.
• When using the quick alignment function to automatically
adjust the image, use a bright, still-picture. It may not
function correctly on a dark or motion picture. If the results
obtained with the quick alignment function are not
satisfactory, manually adjust the "Brightness", "Contrast",
"Horizontal and vertical position", "Phase" and "Tracking" of
the projected image.
35