Adjust The Screen Size (Zooming); Adjust Focus; Setting The Screen Aspect Ratio; Turning Off Image (Hide) - JVC DLA-G150CLU Operating Instructions Manual

Basic Operations
Projector's buttons
STAND BY
LAMP TEMP
OPERATE
HIDE
PC
KEYSTONE
VIDEO
PRESET MENU
PRESET button
EXIT button
EXIT ENTER
Remote control unit
QUICK
ALIGN. OPERATE
HIDE
SCREEN W/S button W W
SCREEN SCREEN FREEZE COMP VIDEO
S S
PC1 PC2 DVI Y/C
FOCUS +/– button
ZOOM T/W button T T
DIGITAL
KEYSTONE ZOOM FOCUS
ZOOM
W W
PRESET button PRESET MENU
EXIT button
EXIT ENTER
RM-M160 REMOTE CONTROL UNIT
34
All manuals and user guides at all-guides.com

3. Adjust the Screen Size (Zooming)

How to adjust the projected screen size differs depending on
the lens unit (optional) you are using.
GL-M2910G (without zooming function):
The projected screen size cannot be changed.
GL-M2915SG/GL-M2920ZG/GL-M2930SZG (with
zooming function):
Adjust the projected screen size with the following buttons on
the remote control unit.
Note
• The function of GL-M2915SG is to adjust the view angle
zooming by 2%. (For fine view angle adjustment)
To enlarge the projected screen size
Press the ZOOM W (Wide) button.
To reduce the screen size
Press the ZOOM T (Tele) button.
Remote control unit
T
DIGITAL
ZOOM
W

4. Adjust Focus

Adjust focus with the following buttons on the remote control unit.
To focus on farther points:
Press the FOCUS + button.
To focus on nearer points:
Press the FOCUS – button.
Remote control unit
FOCUS

5. Setting the Screen Aspect Ratio

Set in accordance with the screen aspect ratio that will be
used. When a screen aspect ratio of 16:9 is used, a 4:3
image can be projected within the screen without using the
zoom function.
When using a 16:9 screen:
Press the "W" button.
When using a 4:3 screen:
Press the "S" button.
Remote control unit
W W
SCREEN SCREEN
S S
* There is no button on the unit.
* This setting can also be performed from the menu. (Refer
to page 46.)
• When using a screen with a 16:9 aspect ratio
When set to "S" (4:3)
* If a 4:3 image is projected, some
parts of the top and bottom of the
image may not be displayed.
When set to "W" (16:9)
* A 4:3 image will be displayed in full
in the middle of the screen.
Projector's buttons
Video image can be temporarily turned off.
STAND BY
LAMP TEMP
OPERATE Press the HIDE button once:
HIDE
Video image instantly turn off.
HIDE
button
Press the HIDE button again:
PC
KEYSTONE
KEYSTONE Video image come on again.
/ buttons VIDEO
PRESET MENU
PRESET
button
EXIT
button
EXIT ENTER
Remote control unit
• When the projected image input is changed, the HIDE
HIDE button
QUICK
ALIGN. OPERATE
If the image projected on the screen is distorted in trapezoid
HIDE
W W
form, correct it with the KEYSTONE buttons on the projector.
SCREEN SCREEN FREEZE COMP VIDEO
S S
PC1 PC2 DVI Y/C When the KEYSTONE button is pressed, "Keystone"
KEYSTONE
appears on the screen together with the level bar and set
T T
/ buttons
DIGITAL
KEYSTONE ZOOM FOCUS
ZOOM
value (–80 to 128). When "15 sec." is displayed in the menu,
W W
PRESET button PRESET MENU
"Keystone" will appear in approximately 15 seconds.
EXIT button
EXIT ENTER
When you press the KEYSTONE
The trapezoid form is corrected as shown in the figure.
RM-M160 REMOTE CONTROL UNIT
When you press the KEYSTONE
The top bottom inverted trapezoid form is corrected as
shown in the figure.
* To cancel correction and restore the original screen, press
* Press the EXIT button to immediately remove the keystone
• The trapezoidal distortion (keystone) can be adjusted from
• The range of the trapezoidal distortion adjustment is
• Interference patterns may appear on the screen when
• Depending on the type of signal, some noise may appear in
Basic Operations

Turning off Image (HIDE)

Remote control unit Projector
HIDE
HIDE
Note
function is canceled and the image return.
Removing the Trapezoidal Distortion of
the Image
Keystone 123
button:
button:
the PRESET button. (Adjusted value:0)
display.
Remote control unit Projector
KEYSTONE KEYSTONE
Projected image with trapezoidal distortion
KEYSTONE
KEYSTONE
Notes
the option menu. (Refer to page 54.)
approximately 20° in the vertical direction.
adjusting the keystone. This is not a malfunction.
the picture when the keystone is adjusted.
This is not a malfunction.
35