Reader Params - Motorola ET1 Integrator Manual

4 - 14 ET1 Enterprise Tablet Integrator Guide
number of times set via UPC/EAN Supplemental Redundancy before transmitting its data to confirm
that there is no supplemental.
•
Supplemental Smart - Enables smart supplementals. In this mode the decoder returns the decoded
value of the main block right away if it does not belong to one of the following supplemental types:
378, 379, 977, 978, 979, 414, 419, 434 or 439. If the bar code starts with one of the prefixes it
searches the image more aggressively for a supplemental. Tries to scan the supplemental if it is
present. If the supplemental scanning failed, then the main bar code is returned.
•
Supplemental 378-379 - Enables (auto-discriminate) supplemental for UPC/EAN codes starting with
378 or 379. Disables reading of supplementals for any other UPC/EAN bar code not starting with 378
or 379. Tries to scan the supplemental if it is present. If the supplemental scanning failed, then the
main bar code is returned.
•
Supplemental 978-979 - Enables (auto-discriminate) supplemental for UPC/EAN codes starting with
978 or 979. Disables reading of supplementals for another UPC/EAN bar code not starting with 978 or
979. Tries to scan the supplemental if it is present. If the supplemental scanning failed, then the main
barcode is returned.
•
Supplemental 414-419-434-439 - Enables (auto-discriminate) supplemental for UPC/EAN codes
starting with 414, 419, 434 or 439. Disables reading of supplementals for another UPC/EAN bar code
not starting with 414, 419, 434 or 439. Tries to scan the supplemental if it is present. If the
supplemental scanning failed, then the main bar code is returned.
•
Supplemental 977 - Enables (auto-discriminate) supplemental for UPC/EAN codes starting with 977.
Disables reading of supplementals for another UPC/EAN barcode not starting with 977. Tries to scan
the supplemental if it is present. If the supplemental scanning failed, then the main bar code is
returned.
•
Retry Count - Retry count for auto-discriminating for supplementals. Possible values are 2 to 20
inclusive. Note that this flag is only considered if Supplemental Mode - UPC EAN is set to one of the
following values: Supplementals Auto, Supplementals Smart, Supplementals 378-379,
Supplementals 978-979, Supplementals 977 or Supplementals 414-419-434-439 (2 to 20, default 10).
•
Bookland - Enable or disable this option. A check in the checkbox indicates that the option is enabled.
•
Coupon - Enables Coupon code decoding. Note that in order to successfully decode Coupon codes, all
of the correct decoders must be enabled. A check in the checkbox indicates that the option is enabled.
•
Convert DataBar To UPC EAN - If this is set it converts DataBar bar codes to UPC/EAN format. For this
setting to work UPC/EAN symbologies must be enabled. A check in the checkbox indicates that the
option is enabled.

Reader Params

Allows the configuration of parameters specific to the selected bar code reader.
•
Beam Timer - Sets the maximum amount of time that the reader remains on (0 - 60,000 ms in
increments of 100 ms). A value of 0 sets the reader to stay on indefinitely (default -15000).
•
Linear Security Level - Sets the number of times a bar code is read to confirm an accurate decode.
•
Security Redundancy and Length - Two times read redundancy based on redundancy flags and
code length.
•
Security Short or Codabar - Two times read redundancy if short bar code or Codabar.
•
Security All Twice - Two times read redundancy for all bar codes (default).
•
Security Long and Short - Two times read redundancy for long bar codes, three times for short bar
codes.
•
Security All Thrice - Three times read redundancy for all bar codes.