Exmark LZUV52 Operator's Manual
Lazer z, lazer z xp
Hide thumbs
Also See for LZUV52:
- Parts manual (40 pages) ,
- Operator's & parts manual (40 pages) ,
- Setup instructions (13 pages)
Related Manuals for Exmark LZUV52
Summary of Contents for Exmark LZUV52
- Page 1 For Ultra Vac Serial Nos. 510,000 & Higher (to fit Units 352,000 & Higher) Part No. 103-8852...
- Page 2 ♦ Keep off mower unless seat platform is provided. ♦ Keep others off mower. Exmark reserves the right to make changes or add improvements to its products at any time without incurring any obligation to make such changes to products manufactured previously. Exmark, or its distributors and dealers, accept no responsibility for variations which may be evident in the actual specifications of its products and the statements and descriptions contained in this publication.
- Page 3 (6) line items or less. If order is received by 3:00 p.m. central time, Exmark ships part(s) direct to dealer or customer, as requested by distributor, same day, overnight UPS Exmark bills the distributor for parts and shipping charges, where applicable.
- Page 4 If additional information is needed, or should you require trained mechanic service, contact your authorized Exmark equipment dealer or distributor. All Exmark equipment dealers and distributors are kept informed of the latest methods of servicing and are equipped to provide prompt and efficient service in the field or at their service stations.
-
Page 5: Table Of Contents
TABLE OF CONTENTS Description Page 1. Safety Safety Alert Symbol ................1 Training ....................1 Preparation ................... 1 Operation................... 2-3 Safety Signs ..................3-4 2. Specifications Model Numbers ..................5 Accessories ..................5 Dimensions................... 5 Bagging System ................... 5 3. Assembly Instructions .1 Assembly Diagram................ -
Page 6: Safety
MAY result in minor or moderate injury. 1.2 TRAINING 1.2.1 Regard the Exmark Ultra Vac as a piece of power equipment and teach this regard to all who operate this unit. 1.2.2 Before operating your Ultra Vac, carefully read and understand this manual and the operator’s manual for your mower in their entirety. -
Page 7: Operation
1.4 OPERATION Although hazard control and accident prevention are partially dependent upon the design and configuration of the equipment, these factors are also dependent upon the awareness, concern, prudence, and proper training of the personnel involved in the operation, transport, maintenance, and storage of the equipment. It is essential that all Operator Safety Mechanisms be connected and in operating condition prior to use for mowing. -
Page 8: Safety Signs
When new components are installed, be sure that current safety signs are affixed to the replaced components. 1.5.4 New safety signs may be obtained from your authorized Exmark equipment dealer or distributor or from Exmark Mfg. Co. Inc. 1.5.5 Safety signs may be affixed by peeling off the backing to expose the adhesive surface. - Page 9 LZUV52 Only PART NO. 103-3508 LOCATION: Top of Blower PART NO. 98-5954 LOCATION: Under Blower Cover PART NO. 103-6606 LOCATION: Top of Front Weight PART NO. 1-653558 PART NO. 1-653554 LOCATION: Top of Idler Arm LOCATION: Rear of Bags PART NO. 103-6607...
-
Page 10: Specifications
SPECIFICATIONS 2.1 MODEL NUMBER: LZUV52 – Fits Lazer Z with 52” deck UV60C – Fits Lazer Z, Lazer Z XP, and Lazer Z XS with 60” deck UV72C – Fits Lazer Z, Lazer Z XP, and Lazer Z XS with 72” deck 2.2 ACCESSORIES... -
Page 11: Assembly Instructions
3. ASSEMBLY INSTRUCTIONS – LAZER Z & LAZER Z XP 3.1 ASSEMBLY DIAGRAM Item Description Item Description 1 Bag Assembly 26 Blocker Plate (small) * 2 Upper Tube 27 Belt Shield Stud 3 Lower Tube 28 3/8-16 x .75 Hex Screw 1-60 only 1-60 only 4 #10-24 CRPH Screw 29 Belt Cover Spacer... -
Page 12: Install Hood Assembly And Bags
3.2 INSTALL THE HOOD ASSEMBLY AND BAGS NOTE: Reference the previous assembly diagrams for the Item numbers called out in the installation instructions. All Lazer Z XP, Lazer Z XS units and Lazer Z Units with SN 510,000 and Higher: (For Lazer Z Units with SN 352,000 –... - Page 13 Lazer Z units with SN 352,000 – 509,999 (Lazer Z XP, Lazer Z XS, and Lazer Z 510,000 units skip to section 3.2.15): 3.2.9 When installing the Ultra Vac onto a liquid cooled Lazer Z, the rear bumper plate must be removed. Remove rear bumper plate. Reattach the lower side bumper bars to the vertical “HOT”...
- Page 14 For installation (or re-installation) of a 2 post foldable ROPS on Lazer Z units with SN 509,999 and Below: 3.2.14 Install the two lower roll bar tubes. a) Align three spacers (Item 47) on each side and tape with masking tape to the rear frame as shown in Figure 3.
- Page 15 For All Lazer Z XP, XS, and Lazer Z Units with a ROPS installed: 3.2.15 Install the upper u-shaped section of the roll bar. (Reference Figure 4 for alignment and installation instructions below): a) Locate the latch pin assemblies (pin and hairpin connected with a lanyard). b) Install a 1/2-13 x 3 1/4 capscrew in the washer on the lanyard of each pin assembly.
-
Page 16: Install Blower Assembly
hook portion over the top mounting tube of the mount weldment. Secure the assembly to the mount using the clevis pins (Item 19) and hairpins (Item 20). 3.2.20 Install the bag assemblies (Item 1) by inserting the hook portion into the slots in the cross bar of the hood assembly. - Page 17 FIGURE 6 BELT ROUTING 3.3.12 Using the knob that was removed with the original belt cover stud and the knob included with the completing kit (Item 40), mount the two belt cover supports (Item 39) to the plastic belt cover (Item 10). Position the belt cover on the mower deck. The lower ends of the belt cover supports should rest on the outside of the deck stiffeners.
-
Page 18: Assemble Tubes
FIGURE 8 3.3.16 Install the belt (Item 13) onto the blower by working it around the impeller sheave. ALL UNITS: 3.3.17 Mount the blower on the deck by sliding the mounting pin into the tube at the rear right corner of the deck. Swing the blower closed. Adjust the position of the front pin to engage the slot in the front of the deck. - Page 19 Lazer Z units prior to 440,000: 3.5.2 Locate the position of the mounting holes. Clamp a weight plate to the front of the floor pan (See Figure 9). The ears on the weight plate should be towards the bottom (upside down from the actual mounted position). Align the bottom edge of the weight plate with the bottom edge of the floor pan front panel.
-
Page 20: Install Removable Weights
Note: The removable weight is heavy. Use care when lifting. Make sure that you can hold the weight securely before lifting. Use caution when positioning your hands so that you do not set the weight down on your hands or fingers. FIGURE 11 (All units with a ROPS) Lazer Z units SN 440,000 and higher:... -
Page 21: Run In - 52" Units Only
3.6.2 Install the removable weight assemblies over the caster arms. On 52 and 60 inch Lazer Z machines one weight has a wide mounting bracket and one has a narrow bracket. They will only fit the machine one way. Weights for the 60 Lazer XP, 60 Lazer XS and all 72s are interchangeable left and right. -
Page 22: Bagger Removal For Side Discharge
4.2.2 To disengage the deck drive and blower, set the throttle to “midway” position. Push in on the PTO switch to the “STOP” position to stop the cutting blades and blower. The cutting blades will require a slightly longer amount of time to come to a complete stop when the blower is installed on the deck. -
Page 23: Transporting
4.3.10 The removable weights must be removed from above the caster wheels (and front of floor pan for units with a 2 post foldable ROPS). To remove the caster weights, loosen the clamping knobs until the weight can be moved relative to the caster arm. - Page 24 WARNING POTENTIAL HAZARD ♦ Loading a unit on a trailer or truck increases the possibility of backward tip-over. WHAT CAN HAPPEN ♦ Backward tip-over of the unit could cause serious injury or death. HOW TO AVOID THE HAZARD ♦ Use extreme caution when operating a unit on a ramp. ♦...
-
Page 25: Maintenance
5. MAINTENANCE: WARNING POTENTIAL HAZARD ♦ While maintenance or adjustments are being made, someone could start the engine. WHAT CAN HAPPEN ♦ Accidental starting of the engine could seriously injure you or other bystanders. HOW TO AVOID THE HAZARD ♦ Remove the key from the ignition switch and pull the wire(s) off the spark plug(s) before you do any maintenance. -
Page 26: Tips And Troubleshooting
6. Tips and Troubleshooting Your Exmark Ultra Vac has been designed to be the most productive bagging system on the market. The following tips have been collected to help you get the most out of your Ultra Vac right from the start. - Page 27 If there is excessive blowout from the deck, check to make sure that the rear screen in the hood is clear of grass build up. It is recommended that the screen and mesh portions of the bags be cleaned regularly to maintain proper air flow. This is especially important in wet conditions.
-
Page 28: Warranty
This warranty extends only to replace or adjust any part manufactured by Exmark and found turf equipment operated under normal conditions. You by us (in the exercise of our reasonable discretion) to be... - Page 29 NOTES...
- Page 30 NOTES...
-
Page 31: Service Record
SERVICE RECORD Date Description of Work Done Service Done By... - Page 32 GRASS CATCHER MICRO-MULCH SYSTEM STEERABLE SULKY SULKY HITCH KIT TURF STRIPER Check us out on the Web: www.exmark.com ©2000-2004 EXMARK MFG. CO. INC. PART NO. 103-8852 INDUSTRIAL PARK BOX 808 (402) 223-6300 BEATRICE, NE 68310 FAX (402) 223-5489 ALL RIGHTS RESERVED PRINTED IN U.S.A.