Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Exmark Manuals
  4. Lawn Mower Accessories
  5. LZUV52
  6. Setup instructions

Exmark LAZER Z LZUV52 Setup Instructions

Ultra vac
Hide thumbs Also See for LAZER Z LZUV52:

Advertisement

Quick Links

Download this manual
Loose Parts
Note: Use the chart below to verify that all parts have been shipped.
109-4231
Dealer Pack
Part #
Description
3296-2
Nut, Nyloc #10-24
3256-61
Washer
32105-13
Screw, HWH #10-24 x 3/4
103-1309
Warranty Registration Form
109-4206
Literature Pack
Part #
Description
109-4207
Manual, Operator's
109-4208
Manual, Parts
Models and Required Completing Kits
Note: Use the chart below to verify the kits required for the unit.
UNIT
Lazer Z 524
(Includes AS)
Lazer Z 524
(Includes AS)
Lazer Z 604
(Includes AS)
Lazer Z 604
(Includes AS)
Lazer Z XS 604
Lazer Z XP 604
Lazer Z 724
Lazer Z 724
Lazer Z XS 724
Lazer Z XP 724
Lazer Z 605 Triton
Lazer Z XS Air Cooled
605 Triton
Lazer Z XS Liquid Cooled 605
Triton
Lazer Z 665 Triton
Lazer Z XS Air Cooled
665 Triton
Lazer Z XS Liquid Cooled 665
Triton
Lazer Z 725 Triton
Lazer Z XS Air Cooled
725 Triton
Lazer Z XS Liquid Cooled 725
Triton
*Units with a 2-post foldable ROPS installed will also require use of 103-5633 Front Weight Kit
Qty
Use
3
3
Installing Tube
3
1
Fill out and return to Exmark
Qty
Use
1
Read before operating machine
1
SERIAL NUMBER
REQ'D TO MOUNT ULTRA VAC
510,000 & Higher
352,000 to 509,999
510,000 & Higher
352,000 to 509,999
440,000 to 599,999
352,000 to 599,999
510,000 & Higher
352,000 to 509,999
440,000 to 599,999
352,000 to 599,999
600,000 & Higher
600,000 & Higher
600,000 & Higher
109-2203 Floor Pan Weight
600,000 & Higher
600,000 & Higher
600,000 & Higher
109-2203 Floor Pan Weight
600,000 & Higher
600,000 & Higher
600,000 & Higher
109-2203 Floor Pan Weight
®
LAZER Z
ULTRA VAC
SETUP INSTRUCTIONS
For Serial Nos. 670,000 and Higher
103-7416 Drive Kit and
103-5633 Front Weight Kit
103-2997 Drive Kit *
109-1179 Drive Kit and
103-5633 Front Weight Kit
109-1189 Drive Kit*
109-1193 Drive Kit and
103-5633 Front Weight Kit
109-1193 Drive Kit*
109-1194 Drive Kit and
103-5633 Front Weight Kit
109-1191 Drive Kit*
109-1194 Drive Kit and
103-5633 Front Weight Kit
109-1194 Drive Kit*
109-1167 Drive Kit
109-1167 Drive Kit
109-1167 Drive Kit and
109-1168 Drive Kit
109-1168 Drive Kit
109-1168 Drive Kit and
109-1169 Drive Kit
109-1169 Drive Kit
109-1169 Drive Kit and
RELEASED Version
Page 1 of 13
109-4232 Rev. A
©Toro 2006-2007

Advertisement

loading

Related Manuals for Exmark LAZER Z LZUV52

Summary of Contents for Exmark LAZER Z LZUV52

  • Page 1 3296-2 Nut, Nyloc #10-24 3256-61 Washer Installing Tube 32105-13 Screw, HWH #10-24 x 3/4 103-1309 Warranty Registration Form Fill out and return to Exmark 109-4206 Literature Pack Part # Description 109-4207 Manual, Operator’s Read before operating machine 109-4208 Manual, Parts Models and Required Completing Kits Note: Use the chart below to verify the kits required for the unit.

  • Page 2: Model Numbers

    Model Numbers LZUV52 – Fits Lazer Z with 52” deck UV60 – Fits Lazer Z, Lazer Z XP, and Lazer Z XS with 60” deck UV6672 – Fits Lazer Z, Lazer XP, and Lazer Z XS with 66” or 72” deck 1.
  • Page 3 Items 21, 22, 26, 29, 30, 37, 38, 39, 44, 46, & 49 not shown *Only required for units with SN 351,999 and below. See Figure 12 for installation of 29 & 30 See Figure 10 for installation of 49 See Figure 5 for installation of 46 See Steps 29 &...

  • Page 4: Install Hood Assembly And Bags

    For Lazer Z XP Lazer Z XS units: Safety 5. Install mount weldment (Item 9) loosely to the Safety Alert Symbol rear bumper using the two holes provided. Secure using (2) 3/8-16 x 1.00 screws (Item 23), This SAFETY ALERT SYMBOL is used (2) 3/8 spring disk washers (Item 25) and (2) 3/8- both in this instruction sheet and on the machine...
  • Page 5 7. Install the frame brackets (Item 16), and ROPS lower roll bar tubes LOOSELY to the mounting CAUTION pads on both sides of the Lazer frame. Use the ROPS mounting hardware, (8) 3/8-16 x 1 ½ POTENTIAL HAZARD screws, (8) 3/8 spring disk washers and (8) 3/8-16 ♦...
  • Page 6 Units without ROPS skip to Step 28: 14. Align three spacers (Item 45) on each side and tape with masking tape to the rear frame as shown in Figure 5. 15. Align lower roll bar tubes along wheel motor channels as shown in Figure 5. 16.
  • Page 7 Installation of Blower Assembly Units SN 352,000-509,999 without splined blade driver: 1. Lower the deck fully. Remove the right hand belt cover. Remove the belt cover mounting stud that protrudes from the deck. 2. Remove the deck drive belt from around the right hand spindle sheave.
  • Page 8 Units SN 600,000 and Lower With Splined Blade 17. Remove the discharge chute from the deck. Discard the mounting hardware, but save the Driver: discharge chute for use during side discharge 9. Lower the deck fully. Remove the right hand belt operation.
  • Page 9 location of the belt cover support holes on the 24. Remove the discharge chute from the deck. Discard the mounting hardware, but save the deck stiffeners. Remove the belt cover. Center discharge chute for use during side discharge punch and drill 3/8” holes. operation.
  • Page 10 33. Install the belt (Item 13) onto the blower by working it around the impeller sheave. WARNING POTENTIAL HAZARD ♦ If the blower intake opening is not correct it will allow objects to be thrown in operator’s or bystander’s direction. Also, contact with blade could occur.
  • Page 11 3. Set deck in lowest cutting position. front panel. Center the weight plate side to side. 4. Slide lower tube onto blower and latch (make sure Mark the position of all four holes using a center that upper tube does not move out of alignment). punch.
  • Page 12 hold the weight securely before lifting. Use Install the Removable Weights caution when positioning your hands so that Note: The removable weights are heavy. Use you do not set the weight down on your hands care when lifting them. Make sure that you can or fingers.

  • Page 13: Operation

    Operation Pre-Start 1. Read the operator’s manual for the mower and Ultra Vac to familiarize yourself with all controls before operating the machine. Make sure that you understand the controls, their locations, their functions, and their safety requirements. 2. Ensure the blower, belt cover, bags, tube and hood are in good condition, properly attached, and latched.

This manual is also suitable for:

Lazer z uv60Lazer z uv6672