Samsung DCS Manual page 52

GPIK: Group Pick Up. Allows calls ringing at a group to be picked up. An extender
can be assigned eg. GPIK 501.
HDSET: * DCS 70 ONLY. Headset Mode. Toggles keyset between Headset & Handset
mode. Key will light when headset mode is set.
HLDPK: Hold Pick Up. Allows a call is on hold to be retrieved by pressing this key
followed by the station number that put the call on hold or the held trunk
number.
IG: In / Out of group. If only IG is entered user must specify which group they wish
to log in/out of. An extender may be assigned to this key eg. IG 501
INQUIRE: Inquire. By pressing this key then entering a trunk number the user can read
the CLIP data for a held call on that trunk.
ISPY: I Spy. Allows station user to view the dialled external number of a busy
extension and gives options to either Barge in or Drop the call. Note: the
station passcode must be changed from the default 1234.
LCR: Lease Cost Route Calls will be made via the most cost effective route, if
programmed.
LISTN: Listen. When on a call using the handset, pressing this key enables the
conversation to be heard through the speaker, the microphone remains muted.
LNR: Last Number Redial.
MMPA: Meet Me Page Answer.
MMPG: Meet Me Page.
MSG: Message Waiting Indication. NOTE: this key is not for SVM-800 message
indication.
MUTE: Mute key. Mutes either the handset or microphone when on a call. The key will
light to indicate the mute condition.
NEW: New Call key:Terminates the existing call, allowing you to make another call.
NIGHT: Night. Allows access to night mode setting (note COS reliant) Lights steady
when system in night mode.
NND: Name Number Display. Pressing this key whilst in conversation will toggle the
display between the CLIP name if any and the CLIP number.
NXT: Next. Displays the CLIP name/number of the waiting call at your station.
OHVA: Off Hook Voice Announcement. Pressing this key after dialling a busy ext on
an external call allows you to communicate with the internal station without
intruding on the conversation.
OPER: Rings assigned operator group. Default 500.
PAGE: Allows a Page call. A valid page zone can be assigned as an extender eg.
PAGE 1 (page zone 1)
PARK: DCS 70 only. Call park / retrieve. Pressing this key places a call on hold in a
park slot; park slot can either be entered after pressing Park key or
programmed as a key extender.
PAUSE: Pause. Inserts a pause (break) in dialled digit stream.
PGPK: Page Pickup Allows a parked call to be picked up when announced via a
page. Pressing this key then a ext number which made the page or the line
number of the parked call will pick up that call
PGMMSG: Program Message. An extender may be programmed to specify a specific
system message number.
REJECT: Blocks an OHVA announcement at the keyset.
RETRY: Retry on Busy. Only for PSTN TKs Retry is given as a soft key option on LCD.
REVW: CLIP Review. Review CLIP information of previous calls.
SETMG: Set Message for ext.
SG: Station Group . Calls a specific group when pressed. eg. SG 501
SNR: Saved Number Redial. Saves a number for dialling later
SP: UCD Supervisor. Enter UCD Supervisor mode. Presents 3 options CALL,
ADMIN , AGENT A Specific group number must be programmed as an
extender eg. SP 510
SPD: Speed Dial. A specific speed dial can be assigned as a key extender eg. SPD
500
SPKR Speaker Key. For use with Falcon Keysets
STORE: Store Clip information in personal speed dial location (uses next free location)
TG: Trunk Group. A specific trunk group can be assigned as a key extender eg. TG
81
Page 43