Mobile Home Installation; Fuel Conversion - Jøtul GF 300 DV Installation And Operation Instructions Manual

Mobile Home Installation

The GF 300 DV can be installed for use in a mobile home
in the U.S. and Canada provided:
1. 1. 1. 1. 1. The stove is secured to the floor of the mobile home.
Use Jøtul Floor Bracket Kit #750304.
2. 2. 2. 2. 2. Provision must be made to secure an electrical ground
between the stove and the mobile home chassis.
3. 3. 3. 3. 3. The stove is installed in accordance with Title 24 CFR,
Part 3280- Manufactured Home Construction and
Safety Standard, in the U.S. In Canada, comply with
CSA Z240.4, Gas Equipped Recreational Vehicles and
Mobile Housing.
4 4 4 4 4 . . . . . Always contact your local officials about installation
restrictions and requirements in your area.
THIS APPLIANCE MAY BE INSTALLED AS AN OEM INSTALLA-
TION IN A MANUFACTURED (MOBILE) HOME AND MUST BE
INSTALLED IN ACCORDANCE WITH THE MANUFACTURER'S
INSTRUCTIONS AND THE MANUFACTURED HOME CON-
STRUCTION AND SAFETY STANDARD, TITLE 24 CFR, PART
3280. THIS APPLIANCE IS ONLY FOR USE WITH THE TYPE OF
GAS THAT IS INDICATED ON THE STOVE'S RATING PLATE. A
GAS CONVERSION KIT IS PROVIDED WITH THE GF 300 DV
GAS STOVE.
THIS APPLIANCE MAY BE INSTALLED IN AN AFTERMARKET
PERMANENTLY LOCATED, MANUFACTURED (MOBILE) HOME,
WHERE NOT PROHIBITED BY LOCAL CODES.
CET APPAREIL PEUT ETRE INSTALLE DANS UN MAISON
PREFABRIQUEE (MOBILE) DEJA INSTALLEE A DEMEURE SI LES
REGLEMENTS LOCAUX LE PERMETTENT. CET APPAREIL DOIT
ETRE UTILISE UNIQUEMENT AVEC LES TYPES DE GAS
INDIQUES SUR LA PLAQUE SIGNALETIQUE. NE PAS
L'UTILISER AVEC D'AUTRES GAS SAUF SI UN KITDE CONVER-
SION CERTIFIE EST INSTALLE.

Fuel Conversion

The GF 300 DV gas stove is shipped from the factory
equipped to burn NATURAL GAS only. If PROPANE gas is
to be used as fuel, the appliance must first be converted
for use with propane. Use Propane Conversion Kit 155372,
supplied with the appliance.
Order and install NG Conversion Kit 155373 to change
back to use with natural gas.
16
WARNING:
THE CONVERSION KIT IS TO BE INSTALLED BY AN
AUTHORIZED JØTUL SERVICE TECHNICIAN IN
ACCORDANCE WITH THE MANUFACTURER'S
INSTRUCTION AND ALL CODES AND
REQUIREMENTS OF THE AUTHORITY HAVING
JURISDICTION. FAILURE TO FOLLOW THESE
INSTRUCTIONS COULD RESULT IN SERIOUS INJURY
OR PROPERTY DAMAGE. THE QUALIFIED AGENCY
PERFORMING THIS WORK ASSUMES
RESPONSIBILITY FOR THIS CONVERSION.
IN CANADA:
THE CONVERSION SHALL BE CARRIED OUT IN
ACCORDANCE WITH THE REQUIREMENTS OF THE
PROVINCIAL AUTHORITIES HAVING JURISDICTION
AND IN ACCORDANCE WITH THE REQUIREMENTS
OF THE CAN1-B149.1 AND .2 INSTALLATION CODE.
Tools required:
• 1/2" open ended wrench or deep-well socket, Torx T20
or slotted screwdriver, 4 mm allen wrench.
Conversion Kit Contents:
• 1, regulator tower labeled for propane
• 3, regulator tower screws
• 1, burner orifice ( ( ( ( ( #39 for NG, #53 for LPG)
• 1, pilot orifice (#51 for NG, #30 for LPG)
• Label A - to be completed and applied to
the back of the stove
• Label B - apply to the stove's Rating Plate
• Small valve label - apply to valve body
Conversion instructions are also shipped in the stove
with the conversion kit.
Figure 22. Locate and remove the Air Shutter wingnut
from under the right side of the stove.
Open
Close