Table of Contents
Advertisement
6. "P-02" is displayed. Repeat steps 4 thru 5 to program the additional tracks.
7. When the selection of track numbers has been finished, press the PLAY button (
program playback.
8. To cancel the program mode, press the STOP ( ).
To check the programmed order
In the stop mode, press (
been programmed.
To add a track to the end of the programmed order:
In the stop mode, press the PROGRAM button.
Select a track number by pressing (
The current track will be added to the end of the program.
To delete the last track from the programmed order:
In the stop mode, press the CLEAR button to delete the last track from the program.
To clear the programmed order:
Press STOP when the CD is already stopped, or press OPEN/CLOSE, POWER, FM/AM,
PHONO, or AUX
1. Press the "FM/AM" button (1).
Press again to switch between AM and FM
2. Tune to the desired station
using the Radio Tuner Knob (2).
Note: In FM Mode,The "TUNED/ST" indicator
lights up green when tuning the Radio Tuner Knob;
The "TUNED/ST" indicator lights up orange when
a station is correctly tuned in.
Adjusting for Best Reception
AM broadcast: Rotate the unit to find the best position.
FM broadcast: Extend and reposition the FM antenna.
Listening to an External Audio Device (AUX Mode)
In AUX (auxiliary) mode, this unit can play audio from an external audio source (iPod, MP3 Player,
Portable CD Player, etc.)
There are two AUX INs(front and rear). When connecting a device that has a headphone jack, use
the cable with 3.5mm plugs on either end with the front AUX IN jack.
The rear set of AUX IN jacks (red and white) can be used with devices that use RCA connections
(DVD players, etc.).
1. Plug one end of the AUX IN cable (included) into the AUX IN (on the front or back of the unit).
2. Plug the other end of the cable into the headphone jack (or RCA jacks) of the external audio
source.
or
) repeatedly to show the track numbers that have
or
), then press the PROGRAM button.
Listening to the Radio
10
) to start
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the ITVS-750 and is the answer not in the manual?
Questions and answers
Turntable won’t spin
The Innovative Technology ITVS-750 turntable may not spin due to the tone arm balancer being incorrectly adjusted. The silver screw on the back of the turntable acts as a balancer for both the turntable and the tone arm. Adjust this screw using a coin and test by moving the tone arm to the middle of the spindle. The tone arm should move freely to the end of the record without resistance before using the turntable.
This answer is automatically generated
The turntable won't spin.
The Innovative Technology ITVS-750 turntable may not spin due to the following reasons:
1. Tone Arm Balance Issue – The silver screw on the back of the turntable acts as a balancer for both the turntable and the tone arm. If it's not adjusted correctly, the tone arm may not move freely, preventing the turntable from spinning. Adjust the screw with a coin until the tone arm moves freely to the middle of the spindle.
2. Tone Arm Holder Secured – If the tone arm is still secured with the fixed rope, it will not function properly. Ensure the fixed rope is loosened and the tone arm is uplifted.
3. Protective Needle Cover Attached – The white protective needle cover must be removed before use. Gently pull it towards the front of the unit.
4. Power Connection Issue – Ensure the AC power cord is properly connected to a wall outlet.
If the turntable still does not spin after checking these points, further troubleshooting may be needed.
This answer is automatically generated
Need replace volume control switch
Need volume control #e-696oai-03
You can control the volume on the Innovative Technology ITVS-750 by turning the "VOLUME" knob. The volume ranges from 00 to 32.
This answer is automatically generated
When i turn the power on the screen lights up for 1-2 seconds and then no power. Nothing works. Where should I start ruling out things.