Siemens SINAMICS V20 Inverter Getting Started page 55

Hide thumbs Also See for SINAMICS V20 Inverter:
Table of Contents

Advertisement

Parameter
Description
P1312[0...2]
Starting boost [%]
P1335[0...2]
Slip compensation [%]
P1336[0...2]
Slip limit [%]
r1348
Economy mode factor [%]
P1800[0...2]
Pulse frequency [kHz]
P1820[0...2]
Reverse output phase sequence
0
1
P1900
Select motor data identification
0
2
r1926
Identified gating unit dead time [μs]
P2010[0...1]
USS / MODBUS baudrate
6
7
8
9
Index:
[0]
[1]
P2011[0...1]
USS address
P2021
Modbus address
P2023
RS485 protocol selection
0
1
2
Notice:
After changing P2023, a power-cycle of the inverter (which may take several seconds) is required.
r2110[0...3]
CO: Warning number
P2157[0...2]
Threshold frequency f_2 [Hz]
P2158[0...2]
Delay time of threshold freq f_2 [ms]
P2159[0...2]
Threshold frequency f_3 [Hz]
P2160[0...2]
Delay time of threshold freq f_3 [ms]
P2200[0...2]
BI: Enable PID controller
P2201[0...2]
Fixed PID setpoint 1 [%]
P2202[0...2]
Fixed PID setpoint 2 [%]
P2203[0...2]
Fixed PID setpoint 3 [%]
P2204[0...2]
Fixed PID setpoint 4 [%]
P2205[0...2]
Fixed PID setpoint 5 [%]
P2206[0...2]
Fixed PID setpoint 6 [%]
P2207[0...2]
Fixed PID setpoint 7 [%]
P2208[0...2]
Fixed PID setpoint 8 [%]
P2209[0...2]
Fixed PID setpoint 9 [%]
P2210[0...2]
Fixed PID setpoint 10 [%]
SINAMICS V20 Inverter
Getting Started, 07/2012, A5E03728127
Forward
Reverse the Motor
Disabled
Identification of all parameters in standstill
9600 bps
19200 bps
38400 bps
57600 bps
USS / MODBUS on RS485
USS on RS232 (reserved)
None
USS
Modbus
Range
Factory default
0.0 - 250.0
0.0
0.0 - 600.0
0.0
0 - 600
250
-
-
2 - 16
4
0 - 1
0
0 - 2
0
-
-
6 - 12
8
10
76800 bps
11
93750 bps
12
115200 bps
0 - 31
0
1 - 247
1
0 - 2
1
-
-
0.00 - 599.00
30.00
0 - 10000
10
0.00 - 599.00
30.00
0 - 10000
10
-
0
-200.00 - 200.00
10.00
-200.00 - 200.00
20.00
-200.00 - 200.00
50.00
-200.00 - 200.00
100.00
-200.00 - 200.00
0.00
-200.00 - 200.00
0.00
-200.00 - 200.00
0.00
-200.00 - 200.00
0.00
-200.00 - 200.00
0.00
-200.00 - 200.00
0.00
Parameter list
Acc. level
2
2
2
2
2
2
2
2
2
2
2
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
55

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Sinamics v20

Table of Contents