Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Jet DC-650A
Summary of Contents for Jet DC-650A
- Page 1 This Manual is Bookmarked Operating Instructions and Parts Manual Dust Collector Model: DC-650A/C/ARC/CRC DC-650ARC shown DC-650C shown WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60123 Part No. M-708640 Ph.: 800-274-6848 Revision G1 12/04 www.wmhtoolgroup.com Copyright © WMH Tool Group...
-
Page 2: Warranty And Service
To obtain maximum life and efficiency from your dust collector and to aid in using it safely, please read this manual thoroughly and follow the instructions carefully. -
Page 3: Table Of Contents
DC-650ARC and DC-650CRC ... 11 Setting the Timer ... 11 Maintenance... 12 Cleaning the Filter Bag – DC-650A/ARC ... 12 Removing the Collector Bag – DC-650A/ARC ... 12 Cleaning the Filter – DC-650C/CRC ... 12 Removing the Collector Bag – DC-650C/CRC ... 12 Motor ... -
Page 4: Warnings
5. Do not use this dust collector for other than its intended use. If used for other purposes, WMH Tool Group disclaims any real or implied warranty and holds itself harmless from any injury that may result from that use. - Page 5 22. Do not use the dust collector for anything except wood dust. Materials such as liquids, metal shavings, metal dust, screws, glass, plastic or rock can cause sparks and/or damage when coming into contact with any part of the dust collector.
-
Page 6: Introduction
If there are any questions or comments, please contact either your local supplier or WMH Tool Group. Specifications DC-650 Series Dust Collector Model ...DC-650A/ARC... DC-650C/CRC Stock Number ...708640/708640RC... 708640C/708641RC Blower Wheel Diameter ... 9.5”... 9.5" Sound Rating at 3 feet ... 65-70 dB...65-70 dB Hose Diameter ...4"... -
Page 7: Unpacking
1. Remove all contents from the shipping carton. 2. Report any damage to your distributor. 3. Do not discard any shipping material until after the dust collector has been assembled and is running properly. Contents of the Shipping Carton DC-650A Contents 1 –... -
Page 8: Assembly
If not loosen the screws that secure the support cylinder to the motor and adjust as necessary. Tighten all hardware. If you are assembling the DC-650A/ARC Dust Collector, proceed to the next section. If you are assembling the DC-650C/CRC Dust Collector, proceed to Canister Installation –... -
Page 9: Filter Bag Installation - Dc-650A/Arc
Filter Bag Installation – DC-650A/ARC 1. Thread an M6 hex nut onto the filter bag support rod, followed by an M6 flat washer and M6 lock washer (A, Fig. 5). Thread the support rod (B, Fig. 5) into the motor/fan housing and tighten nut against the housing. -
Page 10: Canister Installation - Dc-650C/Crc
Canister Installation – DC-650C/CRC 1. Place the canister filter so that it fits snugly over the housing and tighten the four knobs (A, Fig. 7). 2. Mount handle (B, Fig. 7) to the arm (C, Fig. 7) with a M8 flat washer (D, Fig. 7), M8 lock washer (E, Fig. -
Page 11: Electrical Connections
(Figure 9) or from a remote control unit (Figure 10). To start the dust collector, press the ON button. If the remote control unit (Figure 10) is used, aim it at the control panel (Figure 9). The machine will remain running until the OFF button is pressed. -
Page 12: Maintenance
Failure to comply may cause serious injury! Cleaning the Filter Bag – DC-650A/ARC Wearing mask/respirator for protection against fine dust particles during cleaning is highly recommended. During first use and after cleaning, the filter bag may allow some dust to escape. -
Page 13: Parts
32 ... TS-155010... Flat Washer ...M16 ...1 33 ... TS-2361061... Lock Washer...M6 ...8 ... DC650AHP ... Hardware Package (for DC-650A/ARC – not shown) ...1 ... DC650C-HP... Hardware Package (for DC-650C/CRC – not shown)...1 ... DC-IGW ... Inlet Guard Warning Label (not shown)...1 ... - Page 14 Index No. Part No. Description Size 35 ... 331010... Shaft ...1 36 ... 331043... Scraper ...2 37 ... 331015... Plate...2 38 ... 331042... Support ...1 39 ... ST049200 ... Tapping Screw...M4x8...4 40 ... 331011... Arm ...1 41 ... TS-1540071... Hex Nut...M10 ...2 42 ...
-
Page 15: Parts Breakdown
Parts Breakdown for DC-650C/CRC Models for DC-650A/ARC Models... -
Page 16: Remote Control Breakdown For Dc-650Arc/Crc
Remote Control Breakdown for DC-650ARC/CRC Index No. Part No. Description Size ... DC650RC-100 ... Receiver Assembly (Items 1-11) ...1 1 ... DCRC-101 ... Label ...1 2 ... DCRC-102 ... Counter Screw...3 3 ... DCRC-103 ... Switch Plate...1 4 ... DCRC-104 ... Seal...1 5 ... -
Page 17: Wiring Diagrams
Wiring Diagrams DC-650A/C Models 115V 230V... -
Page 18: Dc-650Arc/Crc Models
DC-650ARC/CRC Models... - Page 19 Notes...
- Page 20 WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60123 Phone: 800-274-6848 www.wmhtoolgroup.com...