Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Jet DC-1200A
Summary of Contents for Jet DC-1200A
- Page 1 This Manual is Bookmarked Operating Instructions and Parts Manual Dust Collector Models: DC-1200A/C/RC DC-1200A/RC DC-1200C/RC WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60123 Part No. M-708634 Ph.: 800-274-6848 Revision G 07/04 www.wmhtoolgroup.com Copyright © WMH Tool Group...
-
Page 2: Warranty And Service
This manual has been prepared for the owner and operators of the JET DC-1200 Series Dust Collectors. Its purpose, aside from machine operation, is to promote safety using accepted operating and maintenance procedures. To obtain maximum life and efficiency from your dust collector and to aid in using it safely, please read this manual thoroughly and follow the instructions carefully. -
Page 3: Table Of Contents
DC-1200RC... 13 Setting the Timer ... 13 Maintenance... 14 Cleaning the Filter Bag – DC-1200A/RC... 14 Removing the Collector Bag – DC-1200A/RC ... 14 Cleaning the Filter – DC-1200C/RC... 14 Removing the Collector Bag – DC-1200C/RC ... 14 Motor ... 14 Connecting the Dust Collector to a Machine... -
Page 4: Warnings
5. Do not use this dust collector for other than its intended use. If used for other purposes, WMH Tool Group disclaims any real or implied warranty and holds itself harmless from any injury that may result from that use. - Page 5 22. Do not use the dust collector for anything except wood dust. Materials such as liquids, metal shavings, metal dust, screws, glass, plastic or rock can cause sparks and/or damage when coming into contact with any part of the dust collector.
-
Page 6: Introduction
Introduction This manual is provided by JET covering the safe operation and maintenance procedures for model DC-1200 Series Dust Collectors. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. This machine has been designed and constructed to provide years of trouble free operation if used in accordance to instructions set forth in this manual. -
Page 7: Unpacking
Unpacking DC-1200A/RC Dust Collector 1. Remove all contents from the shipping carton. 2. Report any damage to your distributor. 3. Do not discard any shipping material until after the dust collector has been assembled and is running properly. Contents of the Shipping Carton 1 –... -
Page 8: Dc-1200C/Rc Dust Collector
1. Remove all contents from the shipping carton. 2. Report any damage to your distributor. 3. Do not discard any shipping material until after the dust collector has been assembled and is running properly. Contents of the Shipping Carton Canister Filter Box 1 –... -
Page 9: Assembly
M8 x 16 hex cap screws, four M8 flat washers (B, Fig. 2), and a 13mm wrench. The dust collector must not be connected to the power source during assembly. Failure to comply may result in serious injury! 4. -
Page 10: Connector Housing
(B, Fig. 6). Tighten the clamps to secure the hose. If you are assembling the DC-1200A/RC Dust Collector, proceed to the next section. If you are assembling the DC-1100C/RC Dust Collector, proceed to Collector Bag Installation –... -
Page 11: Filter Bag Installation - Dc-1200A/Rc
Filter Bag Installation – DC-1200A/RC Referring to Figure 7: 1. Place the hanger (A) on the hanger bracket (B). 2. Slide the filter bag loop (C) over the hanger hook. 3. Thread the retainer strap (D) through the loops on the filter bag (E) and fasten to the collector housing (F). -
Page 12: Collector Bag Installation - Dc-1200C/Rc
Collector Bag Installation – DC-1200C/RC 1. Place the ring over the top of the plastic bag and fold over the bag approximately three inches, Figure 9. 2. Insert the snap ring (A, Fig. 10) of the collector bag into the bottom of the housing at an angle. 3. -
Page 13: Electrical Connections
20 amp circuit breaker or fuse. The DC-1200A-3 is rated at 3 Phase 230V/460V, Prewired 230V. If you want to run the DC-1200A-3 on 460V refer to the wiring diagram found on the inside of the switch box cover. -
Page 14: Maintenance
Use the proper type hose to connect the dust collector to the machine being operated. Dryer vent hose is not acceptable for this purpose. Contact your nearest JET distributor for the full line of JET Dust Collector Hoses and Accessories. Customize your installation and obtain maximum performance with JET's dust hoods, hoses, clamps, fittings, and blast gates. -
Page 15: Parts List - Dc-1200A/Rc Dust Collector
... AB430039... Hanger (DC-1200A/RC only)...5 Micron Bag Hanger ...1 24 ... 708698... Filter Bag (DC-1200A/RC only) ...30 Micron Bag ...1 ... 708702... Filter Bag (optional for DC-1200A/RC only) ...5 Micron Bag ...1 25 ... AB410012... Retainer Strap ...1 26 ... 708699A ... Collection Bag (DC-1200A/RC only) ...1 27 ... -
Page 16: Assembly - Dc-1200A/Rc Dust Collector
Assembly – DC-1200A/RC Dust Collector... -
Page 17: Filter Assembly For Dc-1200C/Rc Models
Filter Assembly for DC-1200C/RC Models Index No. Part No. Description Size 1 ... 331050... Handle ...1 2 ... TS-1540071... Hex Nut...M10 ...2 3 ... TS-1550071... Flat Washer ...M10 ...2 4 ... TS-2361101... Lock Washer...M10 ...1 5 ... BR000052... Rivet...5-2 ...3 6 ... -
Page 18: Remote Control Breakdown For Dc-1200Rc
Remote Control Breakdown for DC-1200RC Index No. Part No. Description Size ... DC1200RC-100 ... Receiver Assembly (Items 1-12) ...1 1 ... DCRC-101 ... Label ...1 2 ... DCRC-102 ... Counter Screw...3 3 ... DCRC-103 ... Switch Plate...1 4 ... DCRC-104 ... Seal...1 5 ... -
Page 19: Wiring Diagram
Wiring Diagram DC-1200A-3: 3 Phase 230V/460V DC-1200A-1/DC-1200C... - Page 20 DC-1200RC...