Related Manuals for Jet DC-1200C
Summary of Contents for Jet DC-1200C
- Page 1 DC-1200C Dust Collector JET EQUIPMENT & TOOLS, INC. A WMH Company www.jettools.com OWNER'S MANUAL P.O. BOX 1349 Auburn, WA 98071-1349 e-mail jet@jettools.com Phone:253-351-6000 Fax: 1-800-274-6840 M-708634C 1/02...
-
Page 2: Warranty
This manual has been prepared for the owner and operators of JET’S DC-1200C. Its purpose, aside from machine operation, is to promote safety through the use of accepted correct operating and maintenance procedures. Completely read the safety and maintenance instructions before operating or servicing the machine. - Page 3 Use only as described in this manual. Use only manufacturer’s recommended attachments. Do not use with damaged cord or plug. If Dust Collector is not working as it should, has been dropped, damaged, left outdoor, or dropped in water, return it to a service center.
-
Page 4: Table Of Contents
Maintenance... 9 Cleaning the Filter Bag... 9 Removing the Collector Bag... 9 Motor... 9 Connecting the Dust collector to a Machine ... 9 Grounding the Dust Collection System... 9 Parts Breakdown and Parts List ... 10-12 Wiring Diagrams... 12 The specifications in this manual are given as general information and are not binding. JET Equipment &... -
Page 5: Warnings
Remove all contents from the shipping carton. Report any damage to your distributor. Do not discard any shipping material until after the dust collector has been assembled and is running properly. Contents of the Shipping Cartons Canister Filter Box 1. Canister Filter 1. -
Page 6: Assembly
2) to the base using four M8 x 16 hex cap bolts, four M8 flat washers (B, Fig. 2), and a 13mm wrench. WARNING The dust collector must be disconnected from the power source during assembly. Failure to comply may result in serious injury! 3. - Page 7 4. Attach three support brackets (A, Fig. 4) to the base using six M8 x 16 hex cap bolts and six M8 flat washers (B, Fig. 4). Hand tighten only at this time. 5. Install the housing (A, Fig. 5) to two support brackets using four M8 x 16 hex cap bolts, eight M8 flat washers, and four M8 hex nuts (B, Fig.5).
- Page 8 7. Place the ring over the top of the plastic bag and fold over the bag approximately three inches, Figure 7. 8. Insert the snap ring (A, Fig. 8) of the collector bag into the bottom of the housing at an angle. 9.
-
Page 9: Electrical Connections
Failure to comply may result in serious injury! The DC-1200C dust collector is rated at 230V Only and is not supplied with a plug. Use a plug and outlet rated at least 20 amps. - Page 10 Parts Breakdown for DC-1200C Dust Collector w/Canister Filter...
- Page 11 Parts List for the DC-1200C Dust Collector w/Canister Filter Index Part Description 1...708739... Filter..1 2...331010... Shaft..1 3...331012... Scraper..2 4...331015... Plate..2 5...331009... Support..2 6...ST049200 ... Tapping Screw...M4x8... 4 7...331050... Handle..1 8...NH101700...
-
Page 12: Wiring Diagrams
...DC1200A-NP ... Name Plate (not shown) ..1 ...DC1100-HP... Hardware Package (not shown) ..1 ...DC1200A-CS ... Centrifugal Switch (not shown)..1 ...DC1900-53... Warning Label (not shown) ..1 Wiring Diagram For Single Phase 230V Only Dust Collector Size Qty.